similarity index 91%
rename from arch/arm64/boot/dts/qcom/pm2250.dtsi
rename to arch/arm64/boot/dts/qcom/pm4125.dtsi
@@ -19,7 +19,7 @@ pon@800 {
compatible = "qcom,pm8916-pon";
reg = <0x800>;
- pm2250_pwrkey: pwrkey {
+ pm4125_pwrkey: pwrkey {
compatible = "qcom,pm8941-pwrkey";
interrupts-extended = <&spmi_bus 0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
linux,code = <KEY_POWER>;
@@ -27,7 +27,7 @@ pm2250_pwrkey: pwrkey {
bias-pull-up;
};
- pm2250_resin: resin {
+ pm4125_resin: resin {
compatible = "qcom,pm8941-resin";
interrupts-extended = <&spmi_bus 0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
@@ -43,11 +43,11 @@ rtc@6000 {
interrupts-extended = <&spmi_bus 0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
};
- pm2250_gpios: gpio@c000 {
+ pm4125_gpios: gpio@c000 {
compatible = "qcom,pm2250-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
gpio-controller;
- gpio-ranges = <&pm2250_gpios 0 0 10>;
+ gpio-ranges = <&pm4125_gpios 0 0 10>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
@@ -7,7 +7,7 @@
#include <dt-bindings/leds/common.h>
#include "qcm2290.dtsi"
-#include "pm2250.dtsi"
+#include "pm4125.dtsi"
/ {
model = "Qualcomm Technologies, Inc. Robotics RB1";
@@ -226,7 +226,7 @@ &mdss {
};
&mdss_dsi0 {
- vdda-supply = <&pm2250_l5>;
+ vdda-supply = <&pm4125_l5>;
status = "okay";
};
@@ -239,7 +239,7 @@ &mdss_dsi0_phy {
status = "okay";
};
-&pm2250_resin {
+&pm4125_resin {
linux,code = <KEY_VOLUMEDOWN>;
status = "okay";
};
@@ -263,23 +263,23 @@ regulators {
compatible = "qcom,rpm-pm2250-regulators";
vdd_s3-supply = <&vph_pwr>;
vdd_s4-supply = <&vph_pwr>;
- vdd_l1_l2_l3_l5_l6_l7_l8_l9_l10_l11_l12-supply = <&pm2250_s3>;
+ vdd_l1_l2_l3_l5_l6_l7_l8_l9_l10_l11_l12-supply = <&pm4125_s3>;
vdd_l4_l17_l18_l19_l20_l21_l22-supply = <&vph_pwr>;
- vdd_l13_l14_l15_l16-supply = <&pm2250_s4>;
+ vdd_l13_l14_l15_l16-supply = <&pm4125_s4>;
/*
* S1 - VDD_APC
* S2 - VDD_CX
*/
- pm2250_s3: s3 {
+ pm4125_s3: s3 {
/* 0.4V-1.6625V -> 1.3V (Power tree requirements) */
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
regulator-boot-on;
};
- pm2250_s4: s4 {
+ pm4125_s4: s4 {
/* 1.2V-2.35V -> 2.05V (Power tree requirements) */
regulator-min-microvolt = <2072000>;
regulator-max-microvolt = <2072000>;
@@ -288,7 +288,7 @@ pm2250_s4: s4 {
/* L1 - VDD_MX */
- pm2250_l2: l2 {
+ pm4125_l2: l2 {
/* LPDDR4X VDD2 */
regulator-min-microvolt = <1136000>;
regulator-max-microvolt = <1136000>;
@@ -296,7 +296,7 @@ pm2250_l2: l2 {
regulator-boot-on;
};
- pm2250_l3: l3 {
+ pm4125_l3: l3 {
/* LPDDR4X VDDQ */
regulator-min-microvolt = <616000>;
regulator-max-microvolt = <616000>;
@@ -304,14 +304,14 @@ pm2250_l3: l3 {
regulator-boot-on;
};
- pm2250_l4: l4 {
+ pm4125_l4: l4 {
/* max = 3.05V -> max = 2.7 to disable 3V signaling (SDHCI2) */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2700000>;
regulator-allow-set-load;
};
- pm2250_l5: l5 {
+ pm4125_l5: l5 {
/* CSI/DSI */
regulator-min-microvolt = <1232000>;
regulator-max-microvolt = <1232000>;
@@ -319,7 +319,7 @@ pm2250_l5: l5 {
regulator-boot-on;
};
- pm2250_l6: l6 {
+ pm4125_l6: l6 {
/* DRAM PLL */
regulator-min-microvolt = <928000>;
regulator-max-microvolt = <928000>;
@@ -327,7 +327,7 @@ pm2250_l6: l6 {
regulator-boot-on;
};
- pm2250_l7: l7 {
+ pm4125_l7: l7 {
/* Wi-Fi CX/MX */
regulator-min-microvolt = <664000>;
regulator-max-microvolt = <664000>;
@@ -338,20 +338,20 @@ pm2250_l7: l7 {
* L9 - VDD_LPI_MX
*/
- pm2250_l10: l10 {
+ pm4125_l10: l10 {
/* Wi-Fi RFA */
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
};
- pm2250_l11: l11 {
+ pm4125_l11: l11 {
/* GPS RF1 */
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
};
- pm2250_l12: l12 {
+ pm4125_l12: l12 {
/* USB PHYs */
regulator-min-microvolt = <928000>;
regulator-max-microvolt = <928000>;
@@ -359,7 +359,7 @@ pm2250_l12: l12 {
regulator-boot-on;
};
- pm2250_l13: l13 {
+ pm4125_l13: l13 {
/* USB/QFPROM/PLLs */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
@@ -367,7 +367,7 @@ pm2250_l13: l13 {
regulator-boot-on;
};
- pm2250_l14: l14 {
+ pm4125_l14: l14 {
/* SDHCI1 VQMMC */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
@@ -376,7 +376,7 @@ pm2250_l14: l14 {
regulator-always-on;
};
- pm2250_l15: l15 {
+ pm4125_l15: l15 {
/* WCD/DSI/BT VDDIO */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
@@ -385,38 +385,38 @@ pm2250_l15: l15 {
regulator-boot-on;
};
- pm2250_l16: l16 {
+ pm4125_l16: l16 {
/* GPS RF2 */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
- pm2250_l17: l17 {
+ pm4125_l17: l17 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
- pm2250_l18: l18 {
+ pm4125_l18: l18 {
/* VDD_PXn */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
- pm2250_l19: l19 {
+ pm4125_l19: l19 {
/* VDD_PXn */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
- pm2250_l20: l20 {
+ pm4125_l20: l20 {
/* SDHCI1 VMMC */
regulator-min-microvolt = <2400000>;
regulator-max-microvolt = <3600000>;
regulator-allow-set-load;
};
- pm2250_l21: l21 {
+ pm4125_l21: l21 {
/* SDHCI2 VMMC */
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <3300000>;
@@ -424,7 +424,7 @@ pm2250_l21: l21 {
regulator-boot-on;
};
- pm2250_l22: l22 {
+ pm4125_l22: l22 {
/* Wi-Fi */
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3312000>;
@@ -433,8 +433,8 @@ pm2250_l22: l22 {
};
&sdhc_1 {
- vmmc-supply = <&pm2250_l20>;
- vqmmc-supply = <&pm2250_l14>;
+ vmmc-supply = <&pm4125_l20>;
+ vqmmc-supply = <&pm4125_l14>;
pinctrl-0 = <&sdc1_state_on>;
pinctrl-1 = <&sdc1_state_off>;
pinctrl-names = "default", "sleep";
@@ -446,8 +446,8 @@ &sdhc_1 {
};
&sdhc_2 {
- vmmc-supply = <&pm2250_l21>;
- vqmmc-supply = <&pm2250_l4>;
+ vmmc-supply = <&pm4125_l21>;
+ vqmmc-supply = <&pm4125_l4>;
cd-gpios = <&tlmm 88 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&sdc2_state_on &sd_det_in_on>;
pinctrl-1 = <&sdc2_state_off &sd_det_in_off>;
@@ -518,8 +518,8 @@ &usb {
};
&usb_qmpphy {
- vdda-phy-supply = <&pm2250_l12>;
- vdda-pll-supply = <&pm2250_l13>;
+ vdda-phy-supply = <&pm4125_l12>;
+ vdda-pll-supply = <&pm4125_l13>;
status = "okay";
};
@@ -528,17 +528,17 @@ &usb_dwc3 {
};
&usb_hsphy {
- vdd-supply = <&pm2250_l12>;
- vdda-pll-supply = <&pm2250_l13>;
- vdda-phy-dpdm-supply = <&pm2250_l21>;
+ vdd-supply = <&pm4125_l12>;
+ vdda-pll-supply = <&pm4125_l13>;
+ vdda-phy-dpdm-supply = <&pm4125_l21>;
status = "okay";
};
&wifi {
- vdd-0.8-cx-mx-supply = <&pm2250_l7>;
- vdd-1.8-xo-supply = <&pm2250_l13>;
- vdd-1.3-rfa-supply = <&pm2250_l10>;
- vdd-3.3-ch0-supply = <&pm2250_l22>;
+ vdd-0.8-cx-mx-supply = <&pm4125_l7>;
+ vdd-1.8-xo-supply = <&pm4125_l13>;
+ vdd-1.3-rfa-supply = <&pm4125_l10>;
+ vdd-3.3-ch0-supply = <&pm4125_l22>;
qcom,ath10k-calibration-variant = "Thundercomm_RB1";
status = "okay";
};
According to all the documentation there is no such thing as PM2250, it has been replaced with PM4125. Use correct name for the PMIC. Note, this doesn't change the compatible strings. There was a previous argument regarding renaming of compat strings. Fixes: c309b9a54039 ("arm64: dts: qcom: Add initial PM2250 device tree") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- .../boot/dts/qcom/{pm2250.dtsi => pm4125.dtsi} | 8 +-- arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 78 +++++++++++----------- 2 files changed, 43 insertions(+), 43 deletions(-)