@@ -605,9 +605,6 @@ bimc: interconnect@1008000 {
compatible = "qcom,sdm660-bimc";
reg = <0x01008000 0x78000>;
#interconnect-cells = <1>;
- clock-names = "bus", "bus_a";
- clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
- <&rpmcc RPM_SMD_BIMC_A_CLK>;
};
restart@10ac000 {
@@ -619,18 +616,12 @@ cnoc: interconnect@1500000 {
compatible = "qcom,sdm660-cnoc";
reg = <0x01500000 0x10000>;
#interconnect-cells = <1>;
- clock-names = "bus", "bus_a";
- clocks = <&rpmcc RPM_SMD_CNOC_CLK>,
- <&rpmcc RPM_SMD_CNOC_A_CLK>;
};
snoc: interconnect@1626000 {
compatible = "qcom,sdm660-snoc";
reg = <0x01626000 0x7090>;
#interconnect-cells = <1>;
- clock-names = "bus", "bus_a";
- clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
- <&rpmcc RPM_SMD_SNOC_A_CLK>;
};
anoc2_smmu: iommu@16c0000 {
@@ -685,16 +676,12 @@ a2noc: interconnect@1704000 {
compatible = "qcom,sdm660-a2noc";
reg = <0x01704000 0xc100>;
#interconnect-cells = <1>;
- clock-names = "bus",
- "bus_a",
- "ipa",
+ clock-names = "ipa",
"ufs_axi",
"aggre2_ufs_axi",
"aggre2_usb3_axi",
"cfg_noc_usb2_axi";
- clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>,
- <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>,
- <&rpmcc RPM_SMD_IPA_CLK>,
+ clocks = <&rpmcc RPM_SMD_IPA_CLK>,
<&gcc GCC_UFS_AXI_CLK>,
<&gcc GCC_AGGRE2_UFS_AXI_CLK>,
<&gcc GCC_AGGRE2_USB3_AXI_CLK>,
@@ -705,10 +692,8 @@ mnoc: interconnect@1745000 {
compatible = "qcom,sdm660-mnoc";
reg = <0x01745000 0xa010>;
#interconnect-cells = <1>;
- clock-names = "bus", "bus_a", "iface";
- clocks = <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK>,
- <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK_A>,
- <&mmcc AHB_CLK_SRC>;
+ clock-names = "iface";
+ clocks = <&mmcc AHB_CLK_SRC>;
};
tsens: thermal-sensor@10ae000 {
@@ -2264,12 +2249,6 @@ gnoc: interconnect@17900000 {
compatible = "qcom,sdm660-gnoc";
reg = <0x17900000 0xe000>;
#interconnect-cells = <1>;
- /*
- * This one apparently features no clocks,
- * so let's not mess with the driver needlessly
- */
- clock-names = "bus", "bus_a";
- clocks = <&xo_board>, <&xo_board>;
};
apcs_glb: mailbox@17911000 {
These clocks are now handled from within the icc framework and are no longer registered from within the CCF. Remove them. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 29 ++++------------------------- 1 file changed, 4 insertions(+), 25 deletions(-)