@@ -115,46 +115,54 @@ examples:
- |
#include <dt-bindings/clock/qcom,gcc-msm8916.h>
#include <dt-bindings/interrupt-controller/irq.h>
-
- audio-codec@f000{
- compatible = "qcom,pm8916-wcd-analog-codec";
- reg = <0xf000 0x200>;
- reg-names = "pmic-codec-core";
- clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
- clock-names = "mclk";
- qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
- qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
- interrupt-parent = <&spmi_bus>;
- interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x2 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x3 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x4 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x5 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x6 IRQ_TYPE_NONE>,
- <0x1 0xf0 0x7 IRQ_TYPE_NONE>,
- <0x1 0xf1 0x0 IRQ_TYPE_NONE>,
- <0x1 0xf1 0x1 IRQ_TYPE_NONE>,
- <0x1 0xf1 0x2 IRQ_TYPE_NONE>,
- <0x1 0xf1 0x3 IRQ_TYPE_NONE>,
- <0x1 0xf1 0x4 IRQ_TYPE_NONE>,
- <0x1 0xf1 0x5 IRQ_TYPE_NONE>;
- interrupt-names = "cdc_spk_cnp_int",
- "cdc_spk_clip_int",
- "cdc_spk_ocp_int",
- "mbhc_ins_rem_det1",
- "mbhc_but_rel_det",
- "mbhc_but_press_det",
- "mbhc_ins_rem_det",
- "mbhc_switch_int",
- "cdc_ear_ocp_int",
- "cdc_hphr_ocp_int",
- "cdc_hphl_ocp_det",
- "cdc_ear_cnp_int",
- "cdc_hphr_cnp_int",
- "cdc_hphl_cnp_int";
- vdd-cdc-io-supply = <&pm8916_l5>;
- vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
- vdd-micbias-supply = <&pm8916_l13>;
- #sound-dai-cells = <1>;
+ #include <dt-bindings/spmi/spmi.h>
+
+ pmic@1 {
+ compatible = "qcom,pm8916", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ audio-codec@f000 {
+ compatible = "qcom,pm8916-wcd-analog-codec";
+ reg = <0xf000>;
+ reg-names = "pmic-codec-core";
+ clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
+ clock-names = "mclk";
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ interrupt-parent = <&spmi_bus>;
+ interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x2 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x3 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x4 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x5 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x6 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x7 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x0 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x1 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x2 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x3 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x4 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x5 IRQ_TYPE_NONE>;
+ interrupt-names = "cdc_spk_cnp_int",
+ "cdc_spk_clip_int",
+ "cdc_spk_ocp_int",
+ "mbhc_ins_rem_det1",
+ "mbhc_but_rel_det",
+ "mbhc_but_press_det",
+ "mbhc_ins_rem_det",
+ "mbhc_switch_int",
+ "cdc_ear_ocp_int",
+ "cdc_hphr_ocp_int",
+ "cdc_hphl_ocp_det",
+ "cdc_ear_cnp_int",
+ "cdc_hphr_cnp_int",
+ "cdc_hphl_cnp_int";
+ vdd-cdc-io-supply = <&pm8916_l5>;
+ vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
+ vdd-micbias-supply = <&pm8916_l13>;
+ #sound-dai-cells = <1>;
+ };
};
SPMI devices typically have a single address cell and no size cell, i.e. reg = <0xf000> for the audio codec instead of reg = <0xf000 0x200>. The example is a bit misleading because it uses the latter. Copying this into the device tree would be incorrect and was fixed before for pm8916.dtsi in commit c2f0cbb57dba ("arm64: dts: qcom: pm8916: Remove invalid reg size from wcd_codec"). Make the example more clear by adding the outer "pmic" node which specifies the same #address/size-cells that would be used in the real deivce tree. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> --- .../sound/qcom,pm8916-wcd-analog-codec.yaml | 92 ++++++++++++---------- 1 file changed, 50 insertions(+), 42 deletions(-)