| Message ID | 20230712113539.4029941-5-quic_ipkumar@quicinc.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add IPQ5332 TSENS support | expand |
On 12/07/2023 15:50, Praveenkumar I wrote: > > On 7/12/2023 5:55 PM, Dmitry Baryshkov wrote: >> On 12/07/2023 14:35, Praveenkumar I wrote: >>> This patch adds thermal zone nodes for sensors present in >>> IPQ5332. >>> >>> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>> --- >>> [v2]: >>> Added passive trips and alignment change. >>> >>> arch/arm64/boot/dts/qcom/ipq5332.dtsi | 78 +++++++++++++++++++++++++++ >>> 1 file changed, 78 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> index 0eef77e36609..a1f59af97ee8 100644 >>> --- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> @@ -480,4 +480,82 @@ timer { >>> <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_LOW)>, >>> <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_LOW)>; >>> }; >>> + >>> + thermal-zones { >>> + rfa-0-thermal { >>> + polling-delay-passive = <0>; >>> + polling-delay = <0>; >>> + thermal-sensors = <&tsens 11>; >>> + >>> + trips { >>> + rfa-0-critical { >>> + temperature = <125000>; >>> + hysteresis = <1000>; >>> + type = "critical"; >>> + }; >>> + }; >>> + }; >>> + >>> + rfa-1-thermal { >>> + polling-delay-passive = <0>; >>> + polling-delay = <0>; >>> + thermal-sensors = <&tsens 12>; >>> + >>> + trips { >>> + rfa-1-critical { >>> + temperature = <125000>; >>> + hysteresis = <1000>; >>> + type = "critical"; >>> + }; >>> + }; >>> + }; >>> + >>> + misc-thermal { >>> + polling-delay-passive = <0>; >>> + polling-delay = <0>; >>> + thermal-sensors = <&tsens 13>; >>> + >>> + trips { >>> + misc-critical { >>> + temperature = <125000>; >>> + hysteresis = <1000>; >>> + type = "critical"; >>> + }; >>> + }; >>> + }; >>> + >>> + cpu-top-thermal { >>> + polling-delay-passive = <0>; >>> + polling-delay = <0>; >>> + thermal-sensors = <&tsens 14>; >>> + >>> + trips { >>> + cpu-top-critical { >>> + temperature = <115000>; >>> + hysteresis = <1000>; >>> + type = "critical"; >>> + }; >>> + >>> + cpu-passive { >>> + temperature = <105000>; >>> + hysteresis = <1000>; >>> + type = "passive"; >> >> cooling device for this trip point? > > CPU Frequency scaling support is not yet added for IPQ5332. Planning to > add the cooling device after that in next set of patches. Ack, thanks. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > > - Praveenkumar > >> >>> + }; >>> + }; >>> + }; >>> + >>> + top-glue-thermal { >>> + polling-delay-passive = <0>; >>> + polling-delay = <0>; >>> + thermal-sensors = <&tsens 15>; >>> + >>> + trips { >>> + top-glue-critical { >>> + temperature = <125000>; >>> + hysteresis = <1000>; >>> + type = "critical"; >>> + }; >>> + }; >>> + }; >>> + }; >>> }; >>
diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi index 0eef77e36609..a1f59af97ee8 100644 --- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi @@ -480,4 +480,82 @@ timer { <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; }; + + thermal-zones { + rfa-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 11>; + + trips { + rfa-0-critical { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + rfa-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 12>; + + trips { + rfa-1-critical { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + misc-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 13>; + + trips { + misc-critical { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + cpu-top-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 14>; + + trips { + cpu-top-critical { + temperature = <115000>; + hysteresis = <1000>; + type = "critical"; + }; + + cpu-passive { + temperature = <105000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + top-glue-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 15>; + + trips { + top-glue-critical { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + }; };
This patch adds thermal zone nodes for sensors present in IPQ5332. Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> --- [v2]: Added passive trips and alignment change. arch/arm64/boot/dts/qcom/ipq5332.dtsi | 78 +++++++++++++++++++++++++++ 1 file changed, 78 insertions(+)