@@ -2732,14 +2732,14 @@ dpu_intf0_out: endpoint {
port@1 {
reg = <1>;
dpu_intf1_out: endpoint {
- remote-endpoint = <&dsi0_in>;
+ remote-endpoint = <&mdss_dsi0_in>;
};
};
port@2 {
reg = <2>;
dpu_intf2_out: endpoint {
- remote-endpoint = <&dsi1_in>;
+ remote-endpoint = <&mdss_dsi1_in>;
};
};
@@ -2783,7 +2783,7 @@ opp-460000000 {
};
};
- dsi0: dsi@ae94000 {
+ mdss_dsi0: dsi@ae94000 {
compatible = "qcom,mdss-dsi-ctrl";
reg = <0 0x0ae94000 0 0x400>;
reg-names = "dsi_ctrl";
@@ -2807,7 +2807,7 @@ dsi0: dsi@ae94000 {
operating-points-v2 = <&dsi_opp_table>;
power-domains = <&rpmhpd SC8180X_MMCX>;
- phys = <&dsi0_phy>;
+ phys = <&mdss_dsi0_phy>;
phy-names = "dsi";
status = "disabled";
@@ -2818,14 +2818,14 @@ ports {
port@0 {
reg = <0>;
- dsi0_in: endpoint {
+ mdss_dsi0_in: endpoint {
remote-endpoint = <&dpu_intf1_out>;
};
};
port@1 {
reg = <1>;
- dsi0_out: endpoint {
+ mdss_dsi0_out: endpoint {
};
};
};
@@ -2850,7 +2850,7 @@ opp-358000000 {
};
};
- dsi0_phy: dsi-phy@ae94400 {
+ mdss_dsi0_phy: dsi-phy@ae94400 {
compatible = "qcom,dsi-phy-7nm";
reg = <0 0x0ae94400 0 0x200>,
<0 0x0ae94600 0 0x280>,
@@ -2869,7 +2869,7 @@ dsi0_phy: dsi-phy@ae94400 {
status = "disabled";
};
- dsi1: dsi@ae96000 {
+ mdss_dsi1: dsi@ae96000 {
compatible = "qcom,mdss-dsi-ctrl";
reg = <0 0x0ae96000 0 0x400>;
reg-names = "dsi_ctrl";
@@ -2893,7 +2893,7 @@ dsi1: dsi@ae96000 {
operating-points-v2 = <&dsi_opp_table>;
power-domains = <&rpmhpd SC8180X_MMCX>;
- phys = <&dsi1_phy>;
+ phys = <&mdss_dsi1_phy>;
phy-names = "dsi";
status = "disabled";
@@ -2904,20 +2904,20 @@ ports {
port@0 {
reg = <0>;
- dsi1_in: endpoint {
+ mdss_dsi1_in: endpoint {
remote-endpoint = <&dpu_intf2_out>;
};
};
port@1 {
reg = <1>;
- dsi1_out: endpoint {
+ mdss_dsi1_out: endpoint {
};
};
};
};
- dsi1_phy: dsi-phy@ae96400 {
+ mdss_dsi1_phy: dsi-phy@ae96400 {
compatible = "qcom,dsi-phy-7nm";
reg = <0 0x0ae96400 0 0x200>,
<0 0x0ae96600 0 0x280>,
Currently in board files MDSS and DSI nodes stay apart, because labels for DSI nodes do not have the mdss_ prefix. It was found that grouping all display-related notes is more useful. To keep all display-related nodes close in the board files, change DSI node labels from dsi_* to mdss_dsi_*. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sc8180x.dtsi | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)