@@ -966,6 +966,23 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
return ret;
}
+static int qcom_pcie_post_init_2_7_0(struct qcom_pcie *pcie)
+{
+ struct dw_pcie *pci = pcie->pci;
+ u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+ u32 val;
+
+ dw_pcie_dbi_ro_wr_en(pci);
+
+ val = readl(pci->dbi_base + offset + PCI_EXP_SLTCAP);
+ val &= ~PCI_EXP_SLTCAP_HPC;
+ writel(val, pci->dbi_base + offset + PCI_EXP_SLTCAP);
+
+ dw_pcie_dbi_ro_wr_dis(pci);
+
+ return 0;
+}
+
static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie)
{
struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
@@ -1272,6 +1289,7 @@ static const struct qcom_pcie_ops ops_2_3_3 = {
static const struct qcom_pcie_ops ops_2_7_0 = {
.get_resources = qcom_pcie_get_resources_2_7_0,
.init = qcom_pcie_init_2_7_0,
+ .post_init = qcom_pcie_post_init_2_7_0,
.deinit = qcom_pcie_deinit_2_7_0,
.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
};
@@ -1280,6 +1298,7 @@ static const struct qcom_pcie_ops ops_2_7_0 = {
static const struct qcom_pcie_ops ops_1_9_0 = {
.get_resources = qcom_pcie_get_resources_2_7_0,
.init = qcom_pcie_init_2_7_0,
+ .post_init = qcom_pcie_post_init_2_7_0,
.deinit = qcom_pcie_deinit_2_7_0,
.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
.config_sid = qcom_pcie_config_sid_1_9_0,
SoCs making use of Qcom PCIe controller IPs v2.7.0 and v1.9.0 do not support hotplug functionality. But the hotplug capability bit is set by default in the hardware. This causes the kernel PCI core to register hotplug service for the controller and send hotplug commands to it. But those commands will timeout generating messages as below during boot and suspend/resume. [ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago) [ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago) [ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago) [ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago) This not only spams the console output but also induces a delay of a couple of seconds. To fix this issue, let's clear the HPC bit in PCI_EXP_SLTCAP register as a part of the post init sequence to not advertise the hotplug capability for the controller. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- drivers/pci/controller/dwc/pcie-qcom.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)