| Message ID | 20230505064039.1630025-6-bhupesh.sharma@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add Qualcomm SM6115 / SM4250 EUD dt-bindings & driver support | expand |
On 5.05.2023 08:40, Bhupesh Sharma wrote: > Since the USB-C type port on the Qualcomm QRB4210-RB2 board > can be set primarily in a 'device' configuration (with the default > DIP switch settings), it makes sense to enable the EUD debug > peripheral on the board by default by setting the USB 'dr_mode' property > as 'otg'. > > Now, the EUD debug peripheral can be enabled by executing: > $ echo 1 > /sys/bus/platform/drivers/qcom_eud/1610000.eud/enable > > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 27 +++++++++++++++++++++++- > 1 file changed, 26 insertions(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts > index 1a0776a0cfd0..0ce72f1ebc10 100644 > --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts > +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts > @@ -30,6 +30,10 @@ vph_pwr: vph-pwr-regulator { > }; > }; > > +&eud { > + status = "okay"; > +}; > + > &qupv3_id_0 { > status = "okay"; > }; > @@ -253,7 +257,28 @@ &usb { > > &usb_dwc3 { > maximum-speed = "super-speed"; > - dr_mode = "peripheral"; > + > + /* > + * There is only one USB DWC3 controller on QRB4210 board and it is connected > + * via a DIP Switch: > + * - to either an USB - C type connector or an USB - A type connector > + * (via a GL3590-S hub), and > + * - to either an USB - A type connector (via a GL3590-S hub) or a connector > + * for further connection with a mezzanine board. > + * > + * All of the above hardware muxes would allow us to hook things up in > + * different ways to some potential benefit for static configurations (for e.g. > + * on one hand we can have two USB - A type connectors and a USB - Ethernet > + * connection available and on the other we can use the USB - C type in > + * peripheral mode). > + * > + * Note that since the USB - C type can be used only in peripehral mode, > + * so hardcoding the mode to 'peripheral' here makes sense. > + * > + * However since we want to use the EUD debug device, we set the mode as > + * 'otg' here. > + */ > + dr_mode = "otg"; > }; > > &usb_hsphy {
diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts index 1a0776a0cfd0..0ce72f1ebc10 100644 --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts @@ -30,6 +30,10 @@ vph_pwr: vph-pwr-regulator { }; }; +&eud { + status = "okay"; +}; + &qupv3_id_0 { status = "okay"; }; @@ -253,7 +257,28 @@ &usb { &usb_dwc3 { maximum-speed = "super-speed"; - dr_mode = "peripheral"; + + /* + * There is only one USB DWC3 controller on QRB4210 board and it is connected + * via a DIP Switch: + * - to either an USB - C type connector or an USB - A type connector + * (via a GL3590-S hub), and + * - to either an USB - A type connector (via a GL3590-S hub) or a connector + * for further connection with a mezzanine board. + * + * All of the above hardware muxes would allow us to hook things up in + * different ways to some potential benefit for static configurations (for e.g. + * on one hand we can have two USB - A type connectors and a USB - Ethernet + * connection available and on the other we can use the USB - C type in + * peripheral mode). + * + * Note that since the USB - C type can be used only in peripehral mode, + * so hardcoding the mode to 'peripheral' here makes sense. + * + * However since we want to use the EUD debug device, we set the mode as + * 'otg' here. + */ + dr_mode = "otg"; }; &usb_hsphy {
Since the USB-C type port on the Qualcomm QRB4210-RB2 board can be set primarily in a 'device' configuration (with the default DIP switch settings), it makes sense to enable the EUD debug peripheral on the board by default by setting the USB 'dr_mode' property as 'otg'. Now, the EUD debug peripheral can be enabled by executing: $ echo 1 > /sys/bus/platform/drivers/qcom_eud/1610000.eud/enable Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> --- arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 27 +++++++++++++++++++++++- 1 file changed, 26 insertions(+), 1 deletion(-)