diff mbox series

[v2,14/22] arm64: dts: qcom: sc8280xp*: use pm8350.dtsi

Message ID 20230401220810.3563708-15-dmitry.baryshkov@linaro.org
State New
Headers show
Series arm64: dts: qcom: remove duplication in PMIC declarations | expand

Commit Message

Dmitry Baryshkov April 1, 2023, 10:08 p.m. UTC
Employ PMIC_SID/PMIC_LABEL and switch sc8280xp-pmics to use pm8350.dtsi
in order to reduce duplication and possible discrepancies.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi | 100 ++-----------------
 1 file changed, 9 insertions(+), 91 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
index 6c183b6c9207..69f79ed87f62 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
@@ -7,79 +7,21 @@ 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
-/ {
-	thermal-zones {
-		pm8280_1_thermal: pm8280-1-thermal {
-			polling-delay-passive = <100>;
-			polling-delay = <0>;
-			thermal-sensors = <&pm8280_1_temp_alarm>;
-
-			trips {
-				trip0 {
-					temperature = <95000>;
-					hysteresis = <0>;
-					type = "passive";
-				};
-
-				trip1 {
-					temperature = <115000>;
-					hysteresis = <0>;
-					type = "critical";
-				};
-			};
-		};
-
-		pm8280_2_thermal: pm8280-2-thermal {
-			polling-delay-passive = <100>;
-			polling-delay = <0>;
-			thermal-sensors = <&pm8280_2_temp_alarm>;
-
-			trips {
-				trip0 {
-					temperature = <95000>;
-					hysteresis = <0>;
-					type = "passive";
-				};
-
-				trip1 {
-					temperature = <115000>;
-					hysteresis = <0>;
-					type = "critical";
-				};
-			};
-		};
-	};
-};
-
 /* SID 0 */
 #define PMIC_LABEL pmk8280
 #include "pmk8350.dtsi"
 
-&spmi_bus {
-	pmc8280_1: pmic@1 {
-		compatible = "qcom,pm8350", "qcom,spmi-pmic";
-		reg = <0x1 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
+#define PMIC_SID 1
+#define PMIC_LABEL pmc8280_1
+#define PMIC_NODE pmc82801
+#include "pm8350.dtsi"
 
-		pm8280_1_temp_alarm: temp-alarm@a00 {
-			compatible = "qcom,spmi-temp-alarm";
-			reg = <0xa00>;
-			interrupts-extended = <&spmi_bus 0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
-			#thermal-sensor-cells = <0>;
-		};
-
-		pmc8280_1_gpios: gpio@8800 {
-			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
-			reg = <0x8800>;
-			gpio-controller;
-			gpio-ranges = <&pmc8280_1_gpios 0 0 10>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
+#define PMIC_SID 3
+#define PMIC_LABEL pmc8280_2
+#define PMIC_NODE pmc82802
+#include "pm8350.dtsi"
 
+&spmi_bus {
 	pmc8280c: pmic@2 {
 		compatible = "qcom,pm8350c", "qcom,spmi-pmic";
 		reg = <0x2 SPMI_USID>;
@@ -108,30 +50,6 @@  pmc8280c_lpg: pwm {
 		};
 	};
 
-	pmc8280_2: pmic@3 {
-		compatible = "qcom,pm8350", "qcom,spmi-pmic";
-		reg = <0x3 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pm8280_2_temp_alarm: temp-alarm@a00 {
-			compatible = "qcom,spmi-temp-alarm";
-			reg = <0xa00>;
-			interrupts-extended = <&spmi_bus 0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
-			#thermal-sensor-cells = <0>;
-		};
-
-		pmc8280_2_gpios: gpio@8800 {
-			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
-			reg = <0x8800>;
-			gpio-controller;
-			gpio-ranges = <&pmc8280_2_gpios 0 0 10>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
 	pmr735a: pmic@4 {
 		compatible = "qcom,pmr735a", "qcom,spmi-pmic";
 		reg = <0x4 SPMI_USID>;