diff mbox series

[v2,1/2] cpuidle: psci: Move enabling OSI mode after power domains creation

Message ID 20230330084250.32600-2-quic_mkshah@quicinc.com
State Superseded
Headers show
Series Use PSCI OS initiated mode for sc7280 | expand

Commit Message

Maulik Shah March 30, 2023, 8:42 a.m. UTC
A switch from OSI to PC mode is only possible if all CPUs other than the
calling one are OFF, either through a call to CPU_OFF or not yet booted.

Currently OSI mode is enabled before power domains are created. In cases
where CPUidle states are not using hierarchical CPU topology the bail out
path tries to switch back to PC mode which gets denied by firmware since
other CPUs are online at this point and creates inconsistent state as
firmware is in OSI mode and Linux in PC mode.

This change moves enabling OSI mode after power domains are created,
this would makes sure that hierarchical CPU topology is used before
switching firmware to OSI mode.

Fixes: 70c179b49870 ("cpuidle: psci: Allow PM domain to be initialized even if no OSI mode")
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
---
 drivers/cpuidle/cpuidle-psci-domain.c | 29 +++++++--------------------
 1 file changed, 7 insertions(+), 22 deletions(-)

Comments

Sudeep Holla March 31, 2023, 2:27 p.m. UTC | #1
On Thu, Mar 30, 2023 at 06:40:03PM -0700, Wing Li wrote:
> Adding some clarifications.
> 
> On Thu, Mar 30, 2023 at 6:13 AM Sudeep Holla <sudeep.holla@arm.com> wrote:
> 
> > On Thu, Mar 30, 2023 at 02:06:19PM +0200, Ulf Hansson wrote:
> > > On Thu, 30 Mar 2023 at 11:34, Sudeep Holla <sudeep.holla@arm.com> wrote:
> > > >
> > > > On Thu, Mar 30, 2023 at 02:12:49PM +0530, Maulik Shah wrote:
> > > > > A switch from OSI to PC mode is only possible if all CPUs other than
> > the
> > > > > calling one are OFF, either through a call to CPU_OFF or not yet
> > booted.
> > > > >
> > > >
> > > > As per the spec, all cores are in one of the following states:
> > > >  - Running
> > > >  - OFF, either through a call to CPU_OFF or not yet booted
> > > >  - Suspended, through a call to CPU_DEFAULT_SUSPEND
> > > >
> > > > Better to provide full information.
> >
> 
> The spec quoted above only applies when switching from platform-coordinated
> mode to OS-initiated mode.
> 
> For switching from OS-initiated to platform-coordinated, which is the case
> Maulik is referring to, section 5.20.2 of the spec specifies:
> "A switch from OS-initiated mode to platform-coordinated mode is only
> possible if all cores other than the calling one are OFF, either through a
> call to CPU_OFF or not yet booted."
> 
>

My bad, I read/imagined it as PC->OSI mode couple of times even though it
is pretty explicit. Sorry for that. And thanks a lot for pointing that out.
diff mbox series

Patch

diff --git a/drivers/cpuidle/cpuidle-psci-domain.c b/drivers/cpuidle/cpuidle-psci-domain.c
index 11316c3b14ca..d81f6ae35002 100644
--- a/drivers/cpuidle/cpuidle-psci-domain.c
+++ b/drivers/cpuidle/cpuidle-psci-domain.c
@@ -120,20 +120,6 @@  static void psci_pd_remove(void)
 	}
 }
 
-static bool psci_pd_try_set_osi_mode(void)
-{
-	int ret;
-
-	if (!psci_has_osi_support())
-		return false;
-
-	ret = psci_set_osi_mode(true);
-	if (ret)
-		return false;
-
-	return true;
-}
-
 static void psci_cpuidle_domain_sync_state(struct device *dev)
 {
 	/*
@@ -152,15 +138,12 @@  static int psci_cpuidle_domain_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
 	struct device_node *node;
-	bool use_osi;
+	bool use_osi = psci_has_osi_support();
 	int ret = 0, pd_count = 0;
 
 	if (!np)
 		return -ENODEV;
 
-	/* If OSI mode is supported, let's try to enable it. */
-	use_osi = psci_pd_try_set_osi_mode();
-
 	/*
 	 * Parse child nodes for the "#power-domain-cells" property and
 	 * initialize a genpd/genpd-of-provider pair when it's found.
@@ -178,13 +161,18 @@  static int psci_cpuidle_domain_probe(struct platform_device *pdev)
 
 	/* Bail out if not using the hierarchical CPU topology. */
 	if (!pd_count)
-		goto no_pd;
+		goto remove_pd;
 
 	/* Link genpd masters/subdomains to model the CPU topology. */
 	ret = dt_idle_pd_init_topology(np);
 	if (ret)
 		goto remove_pd;
 
+	/* let's try to enable OSI. */
+	ret = psci_set_osi_mode(use_osi);
+	if (ret)
+		goto remove_pd;
+
 	pr_info("Initialized CPU PM domain topology using %s mode\n",
 		use_osi ? "OSI" : "PC");
 	return 0;
@@ -194,9 +182,6 @@  static int psci_cpuidle_domain_probe(struct platform_device *pdev)
 remove_pd:
 	psci_pd_remove();
 	pr_err("failed to create CPU PM domains ret=%d\n", ret);
-no_pd:
-	if (use_osi)
-		psci_set_osi_mode(false);
 	return ret;
 }