| Message ID | 20230106080911.256232-1-linmengbo0689@protonmail.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: msm8916-gplus-fl8005a: Add initial device tree | expand |
On 6.01.2023 09:10, Lin, Meng-Bo wrote: > GPLUS FL8005A is a tablet using the MSM8916 SoC released in 2015. > > Add a device tree for with initial support for: > > - GPIO keys > - GPIO LEDs > - pm8916-vibrator > - SDHCI (internal and external storage) > - USB Device Mode > - UART > - WCNSS (WiFi/BT) > - Regulators > > Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8916-gplus-fl8005a.dts | 239 ++++++++++++++++++ > 2 files changed, 240 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 3e79496292e7..086654715fc6 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-gplus-fl8005a.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts > new file mode 100644 > index 000000000000..a8e8d5273e75 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts > @@ -0,0 +1,239 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8916-pm8916.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > + > +/ { > + model = "GPLUS FL8005A"; > + compatible = "gplus,fl8005a", "qcom,msm8916"; > + chassis-type = "tablet"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys_default>; > + > + label = "GPIO Buttons"; > + > + button-volume-up { > + label = "Volume Up"; > + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_leds_default>; > + > + led-red { > + function = LED_FUNCTION_CHARGING; > + color = <LED_COLOR_ID_RED>; > + gpios = <&msmgpio 117 GPIO_ACTIVE_HIGH>; > + retain-state-suspended; > + }; > + > + led-green { > + function = LED_FUNCTION_CHARGING; > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&msmgpio 118 GPIO_ACTIVE_HIGH>; > + retain-state-suspended; > + }; > + }; > + > + usb_id: usb-id { > + compatible = "linux,extcon-usb-gpio"; > + id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_id_default>; > + }; > +}; > + > +&blsp1_uart2 { > + status = "okay"; > +}; > + > +&pm8916_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&pm8916_vib { > + status = "okay"; > +}; > + > +&pronto { > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; Please put pinctrl-names after pinctrl-N, as we're trying to keep things consistent with other similar properties, such as: clocks = .. clock-names = .. > + > + status = "okay"; > +}; > + > +&sdhc_2 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; > + > + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; > + > + status = "okay"; > +}; > + > +&usb { > + extcon = <&usb_id>, <&usb_id>; > + status = "okay"; > +}; > + > +&usb_hs_phy { > + extcon = <&usb_id>; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + l1 { > + regulator-min-microvolt = <1225000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l8 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l10 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-system-load = <200000>; > + regulator-allow-set-load; > + }; > + > + l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&msmgpio { > + gpio_keys_default: gpio-keys-default-state { > + pins = "gpio107"; > + function = "gpio"; > + Stray newlines, please remove. Other than that: Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + gpio_leds_default: gpio-led-default-state { > + pins = "gpio117", "gpio118"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + usb_id_default: usb-id-default-state { > + pins = "gpio110"; > + function = "gpio"; > + > + drive-strength = <8>; > + bias-pull-up; > + }; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 3e79496292e7..086654715fc6 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-gplus-fl8005a.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts new file mode 100644 index 000000000000..a8e8d5273e75 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts @@ -0,0 +1,239 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "GPLUS FL8005A"; + compatible = "gplus,fl8005a", "qcom,msm8916"; + chassis-type = "tablet"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + button-volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_leds_default>; + + led-red { + function = LED_FUNCTION_CHARGING; + color = <LED_COLOR_ID_RED>; + gpios = <&msmgpio 117 GPIO_ACTIVE_HIGH>; + retain-state-suspended; + }; + + led-green { + function = LED_FUNCTION_CHARGING; + color = <LED_COLOR_ID_GREEN>; + gpios = <&msmgpio 118 GPIO_ACTIVE_HIGH>; + retain-state-suspended; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pm8916_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; + + status = "okay"; +}; + +&sdhc_2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; + + status = "okay"; +}; + +&usb { + extcon = <&usb_id>, <&usb_id>; + status = "okay"; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-system-load = <200000>; + regulator-allow-set-load; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + gpio_keys_default: gpio-keys-default-state { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gpio_leds_default: gpio-led-default-state { + pins = "gpio117", "gpio118"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + usb_id_default: usb-id-default-state { + pins = "gpio110"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +};
GPLUS FL8005A is a tablet using the MSM8916 SoC released in 2015. Add a device tree for with initial support for: - GPIO keys - GPIO LEDs - pm8916-vibrator - SDHCI (internal and external storage) - USB Device Mode - UART - WCNSS (WiFi/BT) - Regulators Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8916-gplus-fl8005a.dts | 239 ++++++++++++++++++ 2 files changed, 240 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts