diff mbox series

[v2,12/15] arm64: dts: qcom: msm8916: specify per-sensor calibration cells

Message ID 20221204055909.1351895-13-dmitry.baryshkov@linaro.org
State Superseded
Headers show
Series thermal/drivers/tsens: specify nvmem cells in DT rather than parsing them manually | expand

Commit Message

Dmitry Baryshkov Dec. 4, 2022, 5:59 a.m. UTC
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 70 ++++++++++++++++++++++++---
 1 file changed, 64 insertions(+), 6 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 2ca8e977fc2a..af7ba66bb7cd 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -442,11 +442,57 @@  qfprom: qfprom@5c000 {
 			reg = <0x0005c000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			tsens_caldata: caldata@d0 {
-				reg = <0xd0 0x8>;
+			tsens_base1: base1@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 7>;
 			};
-			tsens_calsel: calsel@ec {
-				reg = <0xec 0x4>;
+			tsens_s0_p1: s0_p1@d0 {
+				reg = <0xd0 0x2>;
+				bits = <7 5>;
+			};
+			tsens_s0_p2: s0_p2@d1 {
+				reg = <0xd1 0x2>;
+				bits = <4 5>;
+			};
+			tsens_s1_p1: s1_p1@d2 {
+				reg = <0xd2 0x1>;
+				bits = <1 5>;
+			};
+			tsens_s1_p2: s1_p2@d2 {
+				reg = <0xd2 0x2>;
+				bits = <6 5>;
+			};
+			tsens_s2_p1: s2_p1@d3 {
+				reg = <0xd3 0x1>;
+				bits = <3 5>;
+			};
+			tsens_s2_p2: s2_p2@d4 {
+				reg = <0xd4 0x1>;
+				bits = <0 5>;
+			};
+			tsens_s3_p1: s3_p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <5 5>;
+			};
+			tsens_s3_p2: s3_p2@d5 {
+				reg = <0xd5 0x1>;
+				bits = <2 5>;
+			};
+			tsens_s4_p1: s4_p1@d5 {
+				reg = <0xd5 0x2>;
+				bits = <7 5>;
+			};
+			tsens_s4_p2: s4_p2@d6 {
+				reg = <0xd6 0x2>;
+				bits = <4 5>;
+			};
+			tsens_base2: base2@d7 {
+				reg = <0xd7 0x1>;
+				bits = <1 7>;
+			};
+			tsens_mode: mode@ec {
+				reg = <0xef 0x1>;
+				bits = <5 3>;
 			};
 		};
 
@@ -473,8 +519,20 @@  tsens: thermal-sensor@4a9000 {
 			compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
 			reg = <0x004a9000 0x1000>, /* TM */
 			      <0x004a8000 0x1000>; /* SROT */
-			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
-			nvmem-cell-names = "calib", "calib_sel";
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2";
 			#qcom,sensors = <5>;
 			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "uplow";