@@ -370,8 +370,26 @@ &qupv3_id_1 {
&remoteproc_mpss {
status = "okay";
compatible = "qcom,sc7180-mss-pil";
+ reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
+ reg-names = "qdsp6", "rmb";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+ <&gcc GCC_MSS_NAV_AXI_CLK>,
+ <&gcc GCC_MSS_SNOC_AXI_CLK>,
+ <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo";
+
iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
memory-region = <&mba_mem &mpss_mem>;
+
+ resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+ <&pdc_reset PDC_MODEM_SYNC_RESET>;
+ reset-names = "mss_restart", "pdc_reset";
+
+ qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
+ qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
};
&sdhc_1 {
@@ -851,12 +851,30 @@ &qupv3_id_1 {
&remoteproc_mpss {
status = "okay";
compatible = "qcom,sc7180-mss-pil";
+ reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
+ reg-names = "qdsp6", "rmb";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+ <&gcc GCC_MSS_NAV_AXI_CLK>,
+ <&gcc GCC_MSS_SNOC_AXI_CLK>,
+ <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo";
+
iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
memory-region = <&mba_mem &mpss_mem>;
/* This gets overridden for SKUs with LTE support. */
firmware-name = "qcom/sc7180-trogdor/modem-nolte/mba.mbn",
"qcom/sc7180-trogdor/modem-nolte/qdsp6sw.mbn";
+
+ resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+ <&pdc_reset PDC_MODEM_SYNC_RESET>;
+ reset-names = "mss_restart", "pdc_reset";
+
+ qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
+ qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
};
&sdhc_1 {
@@ -1929,8 +1929,7 @@ pri_mi2s_mclk_active: pri-mi2s-mclk-active-state {
remoteproc_mpss: remoteproc@4080000 {
compatible = "qcom,sc7180-mpss-pas";
- reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
- reg-names = "qdsp6", "rmb";
+ reg = <0 0x04080000 0 0x4040>;
interrupts-extended = <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>,
<&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
@@ -1941,14 +1940,8 @@ remoteproc_mpss: remoteproc@4080000 {
interrupt-names = "wdog", "fatal", "ready", "handover",
"stop-ack", "shutdown-ack";
- clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
- <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
- <&gcc GCC_MSS_NAV_AXI_CLK>,
- <&gcc GCC_MSS_SNOC_AXI_CLK>,
- <&gcc GCC_MSS_MFAB_AXIS_CLK>,
- <&rpmhcc RPMH_CXO_CLK>;
- clock-names = "iface", "bus", "nav", "snoc_axi",
- "mnoc_axi", "xo";
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
power-domains = <&rpmhpd SC7180_CX>,
<&rpmhpd SC7180_MX>,
@@ -1962,13 +1955,6 @@ remoteproc_mpss: remoteproc@4080000 {
qcom,smem-states = <&modem_smp2p_out 0>;
qcom,smem-state-names = "stop";
- resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
- <&pdc_reset PDC_MODEM_SYNC_RESET>;
- reset-names = "mss_restart", "pdc_reset";
-
- qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
- qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
-
status = "disabled";
glink-edge {
The SC7180 MPSS/MSS remote processor can be brought to life using two different bindings: 1. qcom,sc7180-mpss-pas - currently used in DTSI 2. qcom,sc7180-mss-pil Move the properties related to qcom,sc7180-mss-pil (qcom,halt-regs, qcom,spare-regs, resets, additional clocks and regs) to specific boards using the PIL, to silence DT schema warnings. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Changes since v2: 1. New patch. --- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 18 ++++++++++++++++++ arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 18 ++++++++++++++++++ arch/arm64/boot/dts/qcom/sc7180.dtsi | 20 +++----------------- 3 files changed, 39 insertions(+), 17 deletions(-)