@@ -1061,9 +1061,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
struct dw_pcie *pci = pcie->pci;
struct device *dev = pci->dev;
- u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
int i, ret;
- u32 val;
for (i = 0; i < ARRAY_SIZE(res->rst); i++) {
ret = reset_control_assert(res->rst[i]);
@@ -1120,6 +1118,33 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
goto err_clk_aux;
}
+ return 0;
+
+err_clk_aux:
+ clk_disable_unprepare(res->ahb_clk);
+err_clk_ahb:
+ clk_disable_unprepare(res->axi_s_clk);
+err_clk_axi_s:
+ clk_disable_unprepare(res->axi_m_clk);
+err_clk_axi_m:
+ clk_disable_unprepare(res->iface);
+err_clk_iface:
+ /*
+ * Not checking for failure, will anyway return
+ * the original failure in 'ret'.
+ */
+ for (i = 0; i < ARRAY_SIZE(res->rst); i++)
+ reset_control_assert(res->rst[i]);
+
+ return ret;
+}
+
+static int qcom_pcie_post_init_2_3_3(struct qcom_pcie *pcie)
+{
+ struct dw_pcie *pci = pcie->pci;
+ u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+ u32 val;
+
writel(SLV_ADDR_SPACE_SZ,
pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
@@ -1147,24 +1172,6 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
PCI_EXP_DEVCTL2);
return 0;
-
-err_clk_aux:
- clk_disable_unprepare(res->ahb_clk);
-err_clk_ahb:
- clk_disable_unprepare(res->axi_s_clk);
-err_clk_axi_s:
- clk_disable_unprepare(res->axi_m_clk);
-err_clk_axi_m:
- clk_disable_unprepare(res->iface);
-err_clk_iface:
- /*
- * Not checking for failure, will anyway return
- * the original failure in 'ret'.
- */
- for (i = 0; i < ARRAY_SIZE(res->rst); i++)
- reset_control_assert(res->rst[i]);
-
- return ret;
}
static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
@@ -1596,6 +1603,7 @@ static const struct qcom_pcie_ops ops_2_4_0 = {
static const struct qcom_pcie_ops ops_2_3_3 = {
.get_resources = qcom_pcie_get_resources_2_3_3,
.init = qcom_pcie_init_2_3_3,
+ .post_init = qcom_pcie_post_init_2_3_3,
.deinit = qcom_pcie_deinit_2_3_3,
.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
};
Currently the Gen2 port in IPQ8074 will cause the system to hang as its using DBI registers in the .init and those are only accesible after phy_power_on(). So solve this by splitting the DBI read/writes to .post_init. Fixes: a0fd361db8e5 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code") Signed-off-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- Changes in v3: * Make sure it applies onto 5.19-rc3 * Update the commit description to make it clear this only affects the Gen2 port Changes in v2: * Rebase onto next-20220621 --- drivers/pci/controller/dwc/pcie-qcom.c | 48 +++++++++++++++----------- 1 file changed, 28 insertions(+), 20 deletions(-)