From patchwork Tue May 17 20:53:36 2022 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Robert Marko X-Patchwork-Id: 573491 Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 9AB95C4332F for ; Tue, 17 May 2022 20:53:54 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1353035AbiEQUxw (ORCPT ); Tue, 17 May 2022 16:53:52 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:46634 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1353027AbiEQUxt (ORCPT ); Tue, 17 May 2022 16:53:49 -0400 Received: from mail-ed1-x536.google.com (mail-ed1-x536.google.com [IPv6:2a00:1450:4864:20::536]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 5BD025251C; Tue, 17 May 2022 13:53:47 -0700 (PDT) Received: by mail-ed1-x536.google.com with SMTP id er5so423689edb.12; Tue, 17 May 2022 13:53:47 -0700 (PDT) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20210112; h=from:to:cc:subject:date:message-id:mime-version :content-transfer-encoding; bh=xhrqAZKki9p8kfD4Aw0S/OFG/2I4dcqP1LgHwfrZxuc=; b=LQ+6xMv7KgxuTtYylKHTvgkLQsnhgx0E9rc9jm2gWRi//6p2ZwydW9H6kYbLq6S3cK Q6PVFLGch2t5azpG4yvNNqgyJKqsOEVP9hPBAdiZc19Bf00tAFQszb5/8Mci3UByepHR xYx92xQ7Xx0+Ae+bUQ9KMDSCBKTP1MMO8A0vdMyrKs+pCVMkt2qPiMcG5zwhRNS2zr9I hXaQhX0ujNi1lRUtP2/GKiVK738OaXdV4IOlPBBQpmPBzoEeXbatN3L67SUoOFl5VyCq Ws1hZQqvhFSZ4ih8OHQBh8yGKs49rzLxYaFaYmwBHSgOuGKUPpObsIyyBLW25TXS/F5C Ippg== X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=1e100.net; s=20210112; h=x-gm-message-state:from:to:cc:subject:date:message-id:mime-version :content-transfer-encoding; bh=xhrqAZKki9p8kfD4Aw0S/OFG/2I4dcqP1LgHwfrZxuc=; b=QA58eFXfxSqGfrPB1cC8UcW7o9XUEHrYj1poraCy2oGHg/UZ4RHQ+cN77xyFouwX1O CRvjUrVt/6VeT6zP6f7nxqb3mE62rB1a7L9Q3m8HpfrTIdlmyJo6PiMehsHolcBiXLlL GFRPV39hfNKdWM7crdHjjgR4zKcHu39X6Sb9rvBqCqvrjvK+/OLpFxMBUJeK2VR8cfdG PWIjG3YMuSgTKm3WeVI+QC02eNAF8ZgcRungYN/nbuIOaNdl855JXdkYqptXEHBKRWnS /KWjzZTREJqSgeI04xGKSAtu8exxlfZg6mBXSF7PjJHnJNt6HErvs/HecFHliD+TJnp7 woDA== X-Gm-Message-State: AOAM530Udh4nFzmMBkDVSjE0XfgtC/mRpwLYUCcUNttlu4Y3SPUuZk/U t4CzQDou++ccoEGNIMjn1Bu8b78ZXXQojg== X-Google-Smtp-Source: ABdhPJxr94OsSk3vgP8X5sjhTKi8QVGU1mtZYIrnirEaGoP1vXVthmq/px+6OPzX+4EbUGtCEdodow== X-Received: by 2002:a05:6402:3322:b0:42a:d1d2:f76e with SMTP id e34-20020a056402332200b0042ad1d2f76emr2504259eda.353.1652820825649; Tue, 17 May 2022 13:53:45 -0700 (PDT) Received: from fedora.robimarko.hr ([188.252.220.143]) by smtp.googlemail.com with ESMTPSA id v22-20020a17090651d600b006f3ef214e10sm120907ejk.118.2022.05.17.13.53.44 (version=TLS1_3 cipher=TLS_AES_256_GCM_SHA384 bits=256/256); Tue, 17 May 2022 13:53:45 -0700 (PDT) From: Robert Marko To: agross@kernel.org, bjorn.andersson@linaro.org, lgirdwood@gmail.com, broonie@kernel.org, robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org, linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Cc: Robert Marko Subject: [PATCH v3 1/6] dt-bindings: regulator: qcom,spmi-regulator: Convert to dtschema Date: Tue, 17 May 2022 22:53:36 +0200 Message-Id: <20220517205341.536587-1-robimarko@gmail.com> X-Mailer: git-send-email 2.36.1 MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-arm-msm@vger.kernel.org Convert the bindings of Qualcomm SPMI regulators to DT schema. Signed-off-by: Robert Marko --- Changes in v3: * Remove quotes around refs * Use much stricter regex for regulator node matching * Add supply matching per compatible * Add blank interrupts and interrupt-names as generic properties Changes in v2: * Remove the forgotten text bindings * Move allOf after patternProperties * Use my private email as the maintainer email I am aware that syscon alone is not really acceptable, its converted directly from the old text bindings. There is also the issue of some MSM8994, MSM8996 and APQ8096 devices using '#address-cells', '#size-cells', some even defining reg property for regulators. Any advice on how to solve these issues is appreciated. --- .../regulator/qcom,spmi-regulator.txt | 347 ------------------ .../regulator/qcom,spmi-regulator.yaml | 341 +++++++++++++++++ 2 files changed, 341 insertions(+), 347 deletions(-) delete mode 100644 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt create mode 100644 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt deleted file mode 100644 index c2a39b121b1b..000000000000 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ /dev/null @@ -1,347 +0,0 @@ -Qualcomm SPMI Regulators - -- compatible: - Usage: required - Value type: - Definition: must be one of: - "qcom,pm8004-regulators" - "qcom,pm8005-regulators" - "qcom,pm8226-regulators" - "qcom,pm8841-regulators" - "qcom,pm8916-regulators" - "qcom,pm8941-regulators" - "qcom,pm8950-regulators" - "qcom,pm8994-regulators" - "qcom,pmi8994-regulators" - "qcom,pm660-regulators" - "qcom,pm660l-regulators" - "qcom,pms405-regulators" - -- interrupts: - Usage: optional - Value type: - Definition: List of OCP interrupts. - -- interrupt-names: - Usage: required if 'interrupts' property present - Value type: - Definition: List of strings defining the names of the - interrupts in the 'interrupts' property 1-to-1. - Supported values are "ocp-", where - corresponds to a voltage switch - type regulator. - -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s4-supply: -- vdd_s5-supply: -- vdd_s6-supply: -- vdd_s7-supply: -- vdd_s8-supply: - Usage: optional (pm8841 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s4-supply: -- vdd_l1_l3-supply: -- vdd_l2-supply: -- vdd_l4_l5_l6-supply: -- vdd_l7-supply: -- vdd_l8_l11_l14_l15_l16-supply: -- vdd_l9_l10_l12_l13_l17_l18-supply: - Usage: optional (pm8916 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_l1_l3-supply: -- vdd_l2_lvs_1_2_3-supply: -- vdd_l4_l11-supply: -- vdd_l5_l7-supply: -- vdd_l6_l12_l14_l15-supply: -- vdd_l8_l16_l18_19-supply: -- vdd_l9_l10_l17_l22-supply: -- vdd_l13_l20_l23_l24-supply: -- vdd_l21-supply: -- vin_5vs-supply: - Usage: optional (pm8941 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s4-supply: -- vdd_s4-supply: -- vdd_s5-supply: -- vdd_s6-supply: -- vdd_l1_l19-supply: -- vdd_l2_l23-supply: -- vdd_l3-supply: -- vdd_l4_l5_l6_l7_l16-supply: -- vdd_l8_l11_l12_l17_l22-supply: -- vdd_l9_l10_l13_l14_l15_l18-supply: -- vdd_l20-supply: -- vdd_l21-supply: - Usage: optional (pm8950 only) - Value type: - Definition: reference to regulator supplying the input pin, as - described in the data sheet - -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s4-supply: -- vdd_s5-supply: -- vdd_s6-supply: -- vdd_s7-supply: -- vdd_s8-supply: -- vdd_s9-supply: -- vdd_s10-supply: -- vdd_s11-supply: -- vdd_s12-supply: -- vdd_l1-supply: -- vdd_l2_l26_l28-supply: -- vdd_l3_l11-supply: -- vdd_l4_l27_l31-supply: -- vdd_l5_l7-supply: -- vdd_l6_l12_l32-supply: -- vdd_l8_l16_l30-supply: -- vdd_l9_l10_l18_l22-supply: -- vdd_l13_l19_l23_l24-supply: -- vdd_l14_l15-supply: -- vdd_l17_l29-supply: -- vdd_l20_l21-supply: -- vdd_l25-supply: -- vdd_lvs_1_2-supply: - Usage: optional (pm8994 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_l1-supply: - Usage: optional (pmi8994 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_l1_l6_l7-supply: -- vdd_l2_l3-supply: -- vdd_l5-supply: -- vdd_l8_l9_l10_l11_l12_l13_l14-supply: -- vdd_l15_l16_l17_l18_l19-supply: -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s5-supply: -- vdd_s6-supply: - Usage: optional (pm660 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_l1_l9_l10-supply: -- vdd_l2-supply: -- vdd_l3_l5_l7_l8-supply: -- vdd_l4_l6-supply: -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s4-supply: -- vdd_s5-supply: - Usage: optional (pm660l only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- vdd_l1_l2-supply: -- vdd_l3_l8-supply: -- vdd_l4-supply: -- vdd_l5_l6-supply: -- vdd_l10_l11_l12_l13-supply: -- vdd_l7-supply: -- vdd_l9-supply: -- vdd_s1-supply: -- vdd_s2-supply: -- vdd_s3-supply: -- vdd_s4-supply: -- vdd_s5-supply - Usage: optional (pms405 only) - Value type: - Definition: Reference to regulator supplying the input pin, as - described in the data sheet. - -- qcom,saw-reg: - Usage: optional - Value type: - Description: Reference to syscon node defining the SAW registers. - - -The regulator node houses sub-nodes for each regulator within the device. Each -sub-node is identified using the node's name, with valid values listed for each -of the PMICs below. - -pm8004: - s2, s5 - -pm8005: - s1, s2, s3, s4 - -pm8841: - s1, s2, s3, s4, s5, s6, s7, s8 - -pm8916: - s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, - l14, l15, l16, l17, l18 - -pm8941: - s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, - l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, - 5vs1, 5vs2 - -pm8994: - s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, - l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, - l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2 - -pmi8994: - s1, s2, s3, l1 - -The content of each sub-node is defined by the standard binding for regulators - -see regulator.txt - with additional custom properties described below: - -- regulator-initial-mode: - Usage: optional - Value type: - Description: 2 = Set initial mode to auto mode (automatically select - between HPM and LPM); not available on boost type - regulators. - - 1 = Set initial mode to high power mode (HPM), also referred - to as NPM. HPM consumes more ground current than LPM, but - it can source significantly higher load current. HPM is not - available on boost type regulators. For voltage switch type - regulators, HPM implies that over current protection and - soft start are active all the time. - - 0 = Set initial mode to low power mode (LPM). - -- qcom,ocp-max-retries: - Usage: optional - Value type: - Description: Maximum number of times to try toggling a voltage switch - off and back on as a result of consecutive over current - events. - -- qcom,ocp-retry-delay: - Usage: optional - Value type: - Description: Time to delay in milliseconds between each voltage switch - toggle after an over current event takes place. - -- qcom,pin-ctrl-enable: - Usage: optional - Value type: - Description: Bit mask specifying which hardware pins should be used to - enable the regulator, if any; supported bits are: - 0 = ignore all hardware enable signals - BIT(0) = follow HW0_EN signal - BIT(1) = follow HW1_EN signal - BIT(2) = follow HW2_EN signal - BIT(3) = follow HW3_EN signal - -- qcom,pin-ctrl-hpm: - Usage: optional - Value type: - Description: Bit mask specifying which hardware pins should be used to - force the regulator into high power mode, if any; - supported bits are: - 0 = ignore all hardware enable signals - BIT(0) = follow HW0_EN signal - BIT(1) = follow HW1_EN signal - BIT(2) = follow HW2_EN signal - BIT(3) = follow HW3_EN signal - BIT(4) = follow PMIC awake state - -- qcom,vs-soft-start-strength: - Usage: optional - Value type: - Description: This property sets the soft start strength for voltage - switch type regulators; supported values are: - 0 = 0.05 uA - 1 = 0.25 uA - 2 = 0.55 uA - 3 = 0.75 uA - -- qcom,saw-slave: - Usage: optional - Value type: - Description: SAW controlled gang slave. Will not be configured. - -- qcom,saw-leader: - Usage: optional - Value type: - Description: SAW controlled gang leader. Will be configured as - SAW regulator. - -Example: - - regulators { - compatible = "qcom,pm8941-regulators"; - vdd_l1_l3-supply = <&s1>; - - s1: s1 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1400000>; - }; - - ... - - l1: l1 { - regulator-min-microvolt = <1225000>; - regulator-max-microvolt = <1300000>; - }; - - .... - }; - -Example 2: - - saw3: syscon@9A10000 { - compatible = "syscon"; - reg = <0x9A10000 0x1000>; - }; - - ... - - spm-regulators { - compatible = "qcom,pm8994-regulators"; - qcom,saw-reg = <&saw3>; - s8 { - qcom,saw-slave; - }; - s9 { - qcom,saw-slave; - }; - s10 { - qcom,saw-slave; - }; - pm8994_s11_saw: s11 { - qcom,saw-leader; - regulator-always-on; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1140000>; - }; - }; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml new file mode 100644 index 000000000000..7f51e305eaae --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml @@ -0,0 +1,341 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SPMI Regulators + +maintainers: + - Robert Marko + +properties: + compatible: + enum: + - qcom,pm660-regulators + - qcom,pm660l-regulators + - qcom,pm8004-regulators + - qcom,pm8005-regulators + - qcom,pm8226-regulators + - qcom,pm8841-regulators + - qcom,pm8916-regulators + - qcom,pm8941-regulators + - qcom,pm8950-regulators + - qcom,pm8994-regulators + - qcom,pmi8994-regulators + - qcom,pms405-regulators + + interrupts: true + + interrupt-names: true + + qcom,saw-reg: + description: Reference to syscon node defining the SAW registers + $ref: /schemas/types.yaml#/definitions/phandle + +patternProperties: + "^(5vs[1-2]|(l|s)[1-9][0-9]?|lvs[1-3])$": + description: List of regulators and its properties + type: object + $ref: regulator.yaml# + + properties: + qcom,ocp-max-retries: + description: + Maximum number of times to try toggling a voltage switch off and + back on as a result of consecutive over current events + $ref: /schemas/types.yaml#/definitions/uint32 + + qcom,ocp-retry-delay: + description: + Time to delay in milliseconds between each voltage switch toggle + after an over current event takes place + $ref: /schemas/types.yaml#/definitions/uint32 + + qcom,pin-ctrl-enable: + description: + Bit mask specifying which hardware pins should be used to enable the + regulator, if any. + Supported bits are + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + + qcom,pin-ctrl-hpm: + description: + Bit mask specifying which hardware pins should be used to force the + regulator into high power mode, if any. + Supported bits are + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + BIT(4) = follow PMIC awake state + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + + qcom,vs-soft-start-strength: + description: + This property sets the soft start strength for voltage switch type + regulators. + Supported values are + 0 = 0.05 uA + 1 = 0.25 uA + 2 = 0.55 uA + 3 = 0.75 uA + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + + qcom,saw-slave: + description: SAW controlled gang slave. Will not be configured. + type: boolean + + qcom,saw-leader: + description: + SAW controlled gang leader. Will be configured as SAW regulator. + type: boolean + + unevaluatedProperties: false + +required: + - compatible + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,pm660-regulators + then: + properties: + vdd_l15_l16_l17_l18_l19-supply: true + vdd_l1_l6_l7-supply: true + vdd_l2_l3-supply: true + vdd_l5-supply: true + vdd_l8_l9_l10_l11_l12_l13_l14-supply: true + patternProperties: + "^vdd_s[1-6]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm660l-regulators + then: + properties: + vdd_l1_l9_l10-supply: true + vdd_l2-supply: true + vdd_l3_l5_l7_l8-supply: true + vdd_l4_l6-supply: true + patternProperties: + "^vdd_s[1-5]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8004-regulators + then: + patternProperties: + "^vdd_s[25]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8005-regulators + then: + patternProperties: + "^vdd_s[1-4]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8226-regulators + then: + properties: + vdd_l10_l11_l13-supply: true + vdd_l12_l14-supply: true + vdd_l15_l16_l17_l18-supply: true + vdd_l19_l20_l21_l22_l23_l28-supply: true + vdd_l1_l2_l4_l5-supply: true + vdd_l25-supply: true + vdd_l3_l24_l26-supply: true + vdd_l6_l7_l8_l9_l27-supply: true + vdd_lvs1-supply: true + patternProperties: + "^vdd_s[1-5]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8841-regulators + then: + patternProperties: + "^vdd_s[1-8]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8916-regulators + then: + properties: + vdd_l1_l3-supply: true + vdd_l4_l5_l6-supply: true + vdd_l8_l11_l14_l15_l16-supply: true + vdd_l9_l10_l12_l13_l17_l18-supply: true + patternProperties: + "^vdd_l[27]-supply$": true + "^vdd_s[1-4]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8941-regulators + then: + properties: + interrupts: + items: + - description: Over-current protection interrupt for 5V S1 + - description: Over-current protection interrupt for 5V S2 + interrupt-names: + items: + - const: ocp-5vs1 + - const: ocp-5vs2 + vdd_l13_l20_l23_l24-supply: true + vdd_l1_l3-supply: true + vdd_l21-supply: true + vdd_l2_lvs_1_2_3-supply: true + vdd_l4_l11-supply: true + vdd_l5_l7-supply: true + vdd_l6_l12_l14_l15-supply: true + vdd_l8_l16_l18_19-supply: true + vdd_l9_l10_l17_l22-supply: true + vin_5vs-supply: true + patternProperties: + "^vdd_s[1-3]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8950-regulators + then: + properties: + vdd_l1_l19-supply: true + vdd_l20-supply: true + vdd_l21-supply: true + vdd_l2_l23-supply: true + vdd_l3-supply: true + vdd_l4_l5_l6_l7_l16-supply: true + vdd_l8_l11_l12_l17_l22-supply: true + vdd_l9_l10_l13_l14_l15_l18-supply: true + patternProperties: + "^vdd_s[1-6]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8994-regulators + then: + properties: + vdd_l1-supply: true + vdd_l13_l19_l23_l24-supply: true + vdd_l14_l15-supply: true + vdd_l17_l29-supply: true + vdd_l20_l21-supply: true + vdd_l25-supply: true + vdd_l2_l26_l28-supply: true + vdd_l3_l11-supply: true + vdd_l4_l27_l31-supply: true + vdd_l5_l7-supply: true + vdd_l6_l12_l32-supply: true + vdd_l8_l16_l30-supply: true + vdd_l9_l10_l18_l22-supply: true + vdd_lvs_1_2-supply: true + patternProperties: + "^vdd_s[1-9][0-2]?-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pmi8994-regulators + then: + properties: + vdd_l1-supply: true + patternProperties: + "^vdd_s[1-3]-supply$": true + - if: + properties: + compatible: + contains: + enum: + - qcom,pms405-regulators + then: + properties: + vdd_s3-supply: true + +unevaluatedProperties: false + +examples: + - | + regulators { + compatible = "qcom,pm8941-regulators"; + vdd_l1_l3-supply = <&s1>; + + s1: s1 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1400000>; + }; + + l1: l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1300000>; + }; + }; + + - | + saw3: syscon@9a10000 { + compatible = "syscon"; + reg = <0x9a10000 0x1000>; + }; + + regulators { + compatible = "qcom,pm8994-regulators"; + qcom,saw-reg = <&saw3>; + + s8 { + qcom,saw-slave; + }; + + s9 { + qcom,saw-slave; + }; + + s10 { + qcom,saw-slave; + }; + + pm8994_s11_saw: s11 { + qcom,saw-leader; + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1140000>; + }; + }; +...