new file mode 100644
@@ -0,0 +1,153 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm5.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC ADC Thermal Monitoring
+maintainers:
+ - Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+
+properties:
+ compatible:
+ const: qcom,spmi-adc-tm5
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ "#thermal-sensor-cells":
+ const: 1
+ description:
+ Number of cells required to uniquely identify the thermal sensors. Since
+ we have multiple sensors this is set to 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ qcom,avg-samples:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Number of samples to be used for measurement.
+ enum:
+ - 1
+ - 2
+ - 4
+ - 8
+ - 16
+ default: 1
+
+ qcom,decimation:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: This parameter is used to decrease ADC sampling rate.
+ Quicker measurements can be made by reducing decimation ratio.
+ enum:
+ - 250
+ - 420
+ - 840
+ default: 840
+
+patternProperties:
+ "^([-a-z0-9]*)@[0-7]$":
+ type: object
+ description:
+ Represent one thermal sensor.
+
+ properties:
+ reg:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM
+ minimum: 0
+ maximum: 7
+
+ io-channels:
+ description:
+ From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor
+
+ qcom,ratiometric:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Channel calibration type.
+ If this property is specified VADC will use the VDD reference
+ (1.875V) and GND for channel calibration. If property is not found,
+ channel will be calibrated with 0V and 1.25V reference channels,
+ also known as absolute calibration.
+
+ qcom,hw-settle-time-us:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Time between AMUX getting configured and the ADC starting conversion.
+ enum: [15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 8000, 16000, 32000, 64000, 128000]
+
+ qcom,pre-scaling:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Used for scaling the channel input signal before the
+ signal is fed to VADC. The configuration for this node is to know the
+ pre-determined ratio and use it for post scaling. It is a pair of
+ integers, denoting the numerator and denominator of the fraction by
+ which input signal is multiplied. For example, <1 3> indicates the
+ signal is scaled down to 1/3 of its value before ADC measurement. If
+ property is not found default value depending on chip will be used.
+ items:
+ - const: 1
+ - enum: [ 1, 3, 4, 6, 20, 8, 10 ]
+
+ required:
+ - reg
+ - io-channels
+
+ additionalProperties:
+ false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - "#address-cells"
+ - "#size-cells"
+ - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/iio/qcom,spmi-vadc.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spmi_bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pm8150b_adc: adc@3100 {
+ reg = <0x3100>;
+ compatible = "qcom,spmi-adc5";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ /* Other propreties are omitted */
+ conn-therm@4f {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ };
+ };
+
+ pm8150b_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ conn-therm@0 {
+ reg = <0>;
+ io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+ };
+ };
+...