@@ -30,6 +30,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb
new file mode 100644
@@ -0,0 +1,860 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include "sdm845.dtsi"
+
+// Needed for some GPIO (like the volume buttons)
+#include "pm8998.dtsi"
+
+// For LEDs
+#include "pmi8998.dtsi"
+
+/ {
+
+ aliases {
+ hsuart0 = &uart6;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ /*
+ * Apparently RPMh does not provide support for PM8998 S4 because it
+ * is always-on; model it as a fixed regulator.
+ */
+ vreg_s4a_1p8: pm8998-smps4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+
+ gpio_tristate_key: gpio-keys {
+ compatible = "gpio-keys";
+ label = "Tri-state key";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tri_state_key_default>;
+
+ state-top {
+ label = "Tri-state key top";
+ linux,code = <KEY_A>;
+ // gpios = <&tlmm 40 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+ debounce-interval = <500>;
+ linux,can-disable;
+ };
+
+ state-middle {
+ label = "Tri-state key middle";
+ linux,code = <KEY_B>;
+ // gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <52 IRQ_TYPE_EDGE_FALLING>;
+ debounce-interval = <500>;
+ linux,can-disable;
+ };
+
+ state-bottom {
+ label = "Tri-state key bottom";
+ linux,code = <KEY_C>;
+ // gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <126 IRQ_TYPE_EDGE_FALLING>;
+ debounce-interval = <500>;
+ linux,can-disable;
+ };
+ };
+
+ gpio_vol_keys: gpio-keys {
+ compatible = "gpio-keys";
+ label = "Volume keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
+
+ vol-down {
+ label = "Volume down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ };
+
+ vol-up {
+ label = "Volume up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ };
+ };
+
+ extcon_usb1: extcon-usb-1 {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-s11-supply = <&vph_pwr>;
+ vdd-s12-supply = <&vph_pwr>;
+ vdd-s13-supply = <&vph_pwr>;
+ vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+ vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+ vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+ vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+ vdd-l6-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+ vdd-l9-supply = <&vreg_bob>;
+ vdd-l10-l23-l25-supply = <&vreg_bob>;
+ vdd-l13-l19-l21-supply = <&vreg_bob>;
+ vdd-l16-l28-supply = <&vreg_bob>;
+ vdd-l18-l22-supply = <&vreg_bob>;
+ vdd-l20-l24-supply = <&vreg_bob>;
+ vdd-l26-supply = <&vreg_s3a_1p35>;
+ vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s2a_1p125: smps2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ vreg_s3a_1p35: smps3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_s5a_2p04: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_s7a_1p025: smps7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+
+ vdd_qusb_hs0:
+ vdda_hp_pcie_core:
+ vdda_mipi_csi0_0p9:
+ vdda_mipi_csi1_0p9:
+ vdda_mipi_csi2_0p9:
+ vdda_mipi_dsi0_pll:
+ vdda_mipi_dsi1_pll:
+ vdda_qlink_lv:
+ vdda_qlink_lv_ck:
+ vdda_qrefs_0p875:
+ vdda_pcie_core:
+ vdda_pll_cc_ebi01:
+ vdda_pll_cc_ebi23:
+ vdda_sp_sensor:
+ vdda_ufs1_core:
+ vdda_ufs2_core:
+ vdda_usb1_ss_core:
+ vdda_usb2_ss_core:
+ vreg_l1a_0p875: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_10:
+ vreg_l2a_1p2: ldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l3a_1p0: ldo3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_wcss_cx:
+ vdd_wcss_mx:
+ vdda_wcss_pll:
+ vreg_l5a_0p8: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_13:
+ vreg_l6a_1p8: ldo6 {
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <1856000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a_1p2: ldo8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1248000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a_1p8: ldo9 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <2928000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10a_1p8: ldo10 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <2928000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11a_1p0: ldo11 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1048000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_qfprom:
+ vdd_qfprom_sp:
+ vdda_apc1_cs_1p8:
+ vdda_gfx_cs_1p8:
+ vdda_qrefs_1p8:
+ vdda_qusb_hs0_1p8:
+ vddpx_11:
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_2:
+ vreg_l13a_2p95: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14a_1p88: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l15a_1p8: ldo15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16a_2p7: ldo16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a_1p3: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l18a_2p7: ldo18 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l19a_3p0: ldo19 {
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l20a_2p95: ldo20 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l21a_2p95: ldo21 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l22a_2p85: ldo22 {
+ regulator-min-microvolt = <2864000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l23a_3p3: ldo23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_qusb_hs0_3p1:
+ vreg_l24a_3p075: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l25a_3p3: ldo25 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_hp_pcie_1p2:
+ vdda_hv_ebi0:
+ vdda_hv_ebi1:
+ vdda_hv_ebi2:
+ vdda_hv_ebi3:
+ vdda_mipi_csi_1p25:
+ vdda_mipi_dsi0_1p2:
+ vdda_mipi_dsi1_1p2:
+ vdda_pcie_1p2:
+ vdda_ufs1_1p2:
+ vdda_ufs2_1p2:
+ vdda_usb1_ss_1p2:
+ vdda_usb2_ss_1p2:
+ vreg_l26a_1p2: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l28a_3p0: ldo28 {
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_lvs1a_1p8: lvs1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_lvs2a_1p8: lvs2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+
+ pmi8998-rpmh-regulators {
+ compatible = "qcom,pmi8998-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-allow-bypass;
+ };
+ };
+
+ pm8005-rpmh-regulators {
+ compatible = "qcom,pm8005-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s3c_0p6: smps3 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ };
+ };
+};
+
+/* Reserved memory changes */
+/*
+ * The rmtfs memory region in downstream is 'dynamically allocated'
+ * but given the same address every time. hard code it here as this address is
+ * where the modem firmware expects it to be.
+ */
+/delete-node/ &rmtfs_mem;
+
+/ {
+ reserved-memory {
+ rmtfs_mem: memory@f5b01000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0 0xf5b01000 0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ /*
+ * This must be reserved as the device will
+ * crash if memory is allocated here.
+ */
+ removed_region: memory@88f00000 {
+ no-map;
+ reg = <0 0x88f00000 0 0x1c00000>;
+ };
+
+ ramoops: ramoops@ac300000 {
+ compatible = "ramoops";
+ reg = <0 0xac300000 0 0x400000>;
+ record-size = <0x40000>;
+ console-size = <0x40000>;
+ ftrace-size = <0x40000>;
+ pmsg-size = <0x200000>;
+ devinfo-size = <0x1000>;
+ ecc-size = <16>;
+ };
+ };
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <GCC_LPASS_Q6_AXI_CLK>,
+ <GCC_LPASS_SWAY_CLK>;
+};
+
+&gpu {
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
+ };
+};
+
+&adsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
+};
+
+&cdsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
+};
+
+/* Modem/wifi*/
+&mss_pil {
+ status = "okay";
+ firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
+};
+
+&uart6 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ /* In subdir qca/ in /lib/firmware */
+ firmware-name = "oneplus6/crnv21.bin";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&qup_uart6_default {
+ pinmux {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
+ };
+
+ cts {
+ pins = "gpio45";
+ bias-pull-down;
+ };
+
+ rts-tx {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vdda_ufs1_core>;
+ vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+ status = "okay";
+
+ /* disable USB3 clock requirement as we are in USB 2 mode */
+ qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+ /*
+ * Can't detect USB cable being plugged / unplugged, so this is needed
+ * for gadget mode
+ */
+ dr_mode = "peripheral";
+
+ /* fastest mode for USB 2 */
+ maximum-speed = "high-speed";
+
+ extcon = <&extcon_usb1>;
+
+ /* Remove USB3 phy */
+ phys = <&usb_1_hsphy>;
+ phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vdda_usb1_ss_core>;
+ vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+ vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&wifi {
+ status = "okay";
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+ qcom,snoc-host-cap-8bit-quirk;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ display_panel: panel@0 {
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ vddio-supply = <&vreg_l14a_1p88>;
+
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
+
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+};
+
+&dsi0_out {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+ status = "okay";
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+/* GENI device - does i2c, uart, spi and all that stuff */
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ bq27541_battery: bq27541-battery@55 {
+ status = "okay";
+ compatible = "ti,bq27541";
+ reg = <0x55>;
+ };
+};
+
+&i2c12 {
+ status = "okay";
+
+ touchscreen: synaptics-rmi4-i2c@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts-extended = <&tlmm 125 0x2008>; // IRQF_ONESHOT | IRQF_TRIGGER_LOW
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_default_pins &ts_enable_1p8>;
+
+ vdd-supply = <&vreg_l28a_3p0>;
+ vio-supply = <&vreg_l6a_1p8>;
+
+ syna,reset-delay-ms = <200>;
+ syna,startup-delay-ms = <200>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4_f12: rmi4-f12@12 {
+ reg = <0x12>;
+ touchscreen-x-mm = <68>;
+ touchscreen-y-mm = <144>;
+ syna,sensor-type = <1>;
+ syna,rezero-wait-ms = <200>;
+ };
+ };
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_i2c12_default {
+ mux {
+ pins = "gpio49", "gpio50";
+ function = "qup12";
+ };
+ config {
+ pins = "gpio49", "gpio50";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_i2c10_default {
+ pinconf {
+ pins = "gpio55", "gpio56";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_uart9_default {
+ pinconf-tx {
+ pins = "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+&pm8998_gpio {
+ volume_down_gpio: pm8998_gpio5 {
+ pinconf {
+ pins = "gpio5";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <0>;
+ };
+ };
+
+ volume_up_gpio: pm8998_gpio6 {
+ pinconf {
+ pins = "gpio6";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <0>;
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ sdc2_clk: sdc2-clk {
+ pinconf {
+ pins = "sdc2_clk";
+ bias-disable;
+
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16 on clk, cmd, and data pins.
+ */
+ drive-strength = <16>;
+ };
+ };
+
+ sdc2_cmd: sdc2-cmd {
+ pinconf {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ };
+
+ sdc2_data: sdc2-data {
+ pinconf {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ };
+
+ tri_state_key_default: tri_state_key_default {
+ mux {
+ pins = "gpio40", "gpio42", "gpio26";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio40", "gpio42", "gpio26";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ts_default_pins: ts-int {
+ mux {
+ pins = "gpio99", "gpio125";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio99", "gpio125";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ ts_enable_1p8: ts-1p8 {
+ mux {
+ pins = "gpio88";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio88";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ panel_reset_pins: panel-reset {
+ mux {
+ pins = "gpio6", "gpio25", "gpio26";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio6", "gpio25", "gpio26";
+ drive-strength = <8>;
+ bias-disable = <0>;
+ };
+ };
+
+ panel_te_pin: panel-te {
+ mux {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ };
+
+ config {
+ pins = "gpio10";
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+ };
+
+ panel_esd_pin: panel-esd {
+ mux {
+ pins = "gpio30";
+ function = "gpio";
+ };
+ config {
+ pins = "gpio30";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6 (enchilada) specific device tree
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "sdm845-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 6";
+ compatible = "oneplus,enchilada", "oneplus,oneplus6", "qcom,sdm845";
+};
+
+&display_panel {
+ status = "okay";
+
+ compatible = "samsung,sofef00";
+};
new file mode 100644
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6T (fajita) specific device tree
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "sdm845-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 6T";
+ compatible = "oneplus,fajita", "oneplus,oneplus6", "qcom,sdm845";
+};
+
+&display_panel {
+ status = "okay";
+
+ compatible = "samsung,s6e3fc2x01";
+};
Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based on the sdm845-mtp DT. Support includes: * Both display panels work * Touch screen support with rmi4 * RTC support * Remoteprocs boot and can be interacted with over QRTR. * WLAN + Bluetooth both work, although bluetooth doesn't appear in rfkill. * Volume / power buttons and OnePlus Tri-State switch are functional * USB gadget support is forced as it doesn't seem to be able to detect USB cable connect/disconnect, perhaps to do with OnePlus' propriatery fast charge IC. The device successfully boots into Phosh using postmarketOS. Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 860 ++++++++++++++++++ .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 + .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 19 + 4 files changed, 900 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts