| Message ID | 20201007174736.292968-2-caleb@connolly.tech |
|---|---|
| State | New |
| Headers | show |
| Series | [1/5] drm/panel/oneplus6: Add panel-oneplus6 | expand |
Hi Caleb. I have missed to provice review feedback so here goes. There is some improvements that can be made as the infrastructure has evolved since the driver was started. But despite the number of comments below it is all trivial and the driver looks good in general. I look forward to see the next revision. Sam On Wed, Oct 07, 2020 at 05:49:08PM +0000, Caleb Connolly wrote: > This commit adds support for the display panels used in the OnePlus 6 / > T devices. > > The OnePlus 6/T devices use different panels however they are > functionally identical with much of the commands being shared. The > panels don't appear to be used by any other devices some combine them as > one driver that is specific to the devices. > > The panels are: samsung,sofef00 > and samsung,s6e3fc2x01 > > Signed-off-by: Caleb Connolly <caleb@connolly.tech> > --- > drivers/gpu/drm/panel/Kconfig | 12 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-oneplus6.c | 418 +++++++++++++++++++++++++ It would be better to name the driver after the panels and not their user. So something like panel-samsung-sofef00. It is OK to name it after one panel and let it support mroe than one panel. The Kconfig description could then expain where it is used. > 3 files changed, 431 insertions(+) > create mode 100644 drivers/gpu/drm/panel/panel-oneplus6.c > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > index de2f2a452be5..d72862265400 100644 > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -229,6 +229,18 @@ config DRM_PANEL_OLIMEX_LCD_OLINUXINO > Say Y here if you want to enable support for Olimex Ltd. > LCD-OLinuXino panel. > > +config DRM_PANEL_ONEPLUS6 > + tristate "OnePlus 6/6T Samsung AMOLED DSI command mode panels" > + depends on OF > + depends on DRM_MIPI_DSI > + depends on BACKLIGHT_CLASS_DEVICE > + select VIDEOMODE_HELPERS > + help > + Say Y or M here if you want to enable support for the Samsung AMOLED > + command mode panels found in the OnePlus 6/6T smartphones. > + > + The panels are 2280x1080@60Hz and 2340x1080@60Hz respectively > + > config DRM_PANEL_ORISETECH_OTM8009A > tristate "Orise Technology otm8009a 480x800 dsi 2dl panel" > depends on OF > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > index e45ceac6286f..017539056f53 100644 > --- a/drivers/gpu/drm/panel/Makefile > +++ b/drivers/gpu/drm/panel/Makefile > @@ -21,6 +21,7 @@ obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o > obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o > obj-$(CONFIG_DRM_PANEL_NOVATEK_NT39016) += panel-novatek-nt39016.o > obj-$(CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO) += panel-olimex-lcd-olinuxino.o > +obj-$(CONFIG_DRM_PANEL_ONEPLUS6) += panel-oneplus6.o > obj-$(CONFIG_DRM_PANEL_ORISETECH_OTM8009A) += panel-orisetech-otm8009a.o > obj-$(CONFIG_DRM_PANEL_OSD_OSD101T2587_53TS) += panel-osd-osd101t2587-53ts.o > obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o > diff --git a/drivers/gpu/drm/panel/panel-oneplus6.c b/drivers/gpu/drm/panel/panel-oneplus6.c > new file mode 100644 > index 000000000000..5e212774b1e0 > --- /dev/null > +++ b/drivers/gpu/drm/panel/panel-oneplus6.c > @@ -0,0 +1,418 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* Copyright (c) 2020 Caleb Connolly <caleb@connolly.tech> > + * Generated with linux-mdss-dsi-panel-driver-generator from vendor device tree: > + * Copyright (c) 2020, The Linux Foundation. All rights reserved. > + * > + * Caleb Connolly <caleb@connolly.tech> > + */ > + > +#include <linux/delay.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/regulator/consumer.h> > + > +#include <video/mipi_display.h> > + > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_modes.h> > +#include <drm/drm_panel.h> > +#include <linux/backlight.h> Keep all linux include together. > + > +struct oneplus6_panel { > + struct drm_panel panel; > + struct mipi_dsi_device *dsi; > + struct backlight_device *backlight; Use drm_panel backlight support - so you can drop this variable and simplify some of the code below. > + struct regulator *supply; > + struct gpio_desc *reset_gpio; > + struct gpio_desc *enable_gpio; The enable_gpio is not used. > + const struct drm_display_mode *mode; > + bool prepared; > + bool enabled; > +}; > + > +static inline > +struct oneplus6_panel *to_oneplus6_panel(struct drm_panel *panel) > +{ > + return container_of(panel, struct oneplus6_panel, panel); > +} > + > +#define dsi_dcs_write_seq(dsi, seq...) do { \ > + static const u8 d[] = { seq }; \ > + int ret; \ > + ret = mipi_dsi_dcs_write_buffer(dsi, d, ARRAY_SIZE(d)); \ > + if (ret < 0) \ > + return ret; \ > + } while (0) > + > +static void oneplus6_panel_reset(struct oneplus6_panel *ctx) > +{ > + gpiod_set_value_cansleep(ctx->reset_gpio, 1); > + usleep_range(5000, 6000); > +} IT is not obvious if this helper reset the panel or de-assert the reset signal. It does not help me that there is only one helper despite both operatiosn are needed. > + > +static int oneplus6_panel_on(struct oneplus6_panel *ctx) > +{ > + struct mipi_dsi_device *dsi = ctx->dsi; > + struct device *dev = &dsi->dev; > + int ret; > + > + dsi->mode_flags |= MIPI_DSI_MODE_LPM; > + > + ret = mipi_dsi_dcs_exit_sleep_mode(dsi); > + if (ret < 0) { > + dev_err(dev, "Failed to exit sleep mode: %d\n", ret); > + return ret; > + } > + usleep_range(10000, 11000); > + > + dsi_dcs_write_seq(dsi, 0xf0, 0x5a, 0x5a); > + > + ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK); > + if (ret < 0) { > + dev_err(dev, "Failed to set tear on: %d\n", ret); > + return ret; > + } > + > + dsi_dcs_write_seq(dsi, 0xf0, 0xa5, 0xa5); > + dsi_dcs_write_seq(dsi, 0xf0, 0x5a, 0x5a); > + dsi_dcs_write_seq(dsi, 0xb0, 0x07); > + dsi_dcs_write_seq(dsi, 0xb6, 0x12); > + dsi_dcs_write_seq(dsi, 0xf0, 0xa5, 0xa5); > + dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x20); > + dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_POWER_SAVE, 0x00); > + > + ret = mipi_dsi_dcs_set_display_on(dsi); > + if (ret < 0) { > + dev_err(dev, "Failed to set display on: %d\n", ret); > + return ret; > + } > + > + return 0; > +} > + > +static int oneplus6_panel_off(struct oneplus6_panel *ctx) > +{ > + struct mipi_dsi_device *dsi = ctx->dsi; > + struct device *dev = &dsi->dev; > + int ret; > + > + dsi->mode_flags &= ~MIPI_DSI_MODE_LPM; > + > + ret = mipi_dsi_dcs_set_display_off(dsi); > + if (ret < 0) { > + dev_err(dev, "Failed to set display off: %d\n", ret); > + return ret; > + } > + msleep(40); > + > + ret = mipi_dsi_dcs_enter_sleep_mode(dsi); > + if (ret < 0) { > + dev_err(dev, "Failed to enter sleep mode: %d\n", ret); > + return ret; > + } > + msleep(160); > + > + return 0; > +} > + > +static int oneplus6_panel_prepare(struct drm_panel *panel) > +{ > + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); > + struct device *dev = &ctx->dsi->dev; > + int ret; > + > + if (ctx->prepared) > + return 0; > + Do you not need to do a regulator_enable() here to get power supply to the panel? > + oneplus6_panel_reset(ctx); > + > + ret = oneplus6_panel_on(ctx); > + if (ret < 0) { > + dev_err(dev, "Failed to initialize panel: %d\n", ret); > + gpiod_set_value_cansleep(ctx->reset_gpio, 0); > + return ret; > + } > + > + ctx->prepared = true; > + return 0; > +} > + > +static int oneplus6_panel_unprepare(struct drm_panel *panel) > +{ > + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); > + struct device *dev = &ctx->dsi->dev; > + int ret; > + > + if (!ctx->prepared) > + return 0; > + > + ret = regulator_enable(ctx->supply); Looks strange that the power supply is enabled here - was it not enabled before to use the panel? > + if (ret < 0) { > + dev_err(dev, "Failed to enable regulator: %d\n", ret); > + return ret; > + } > + > + ret = oneplus6_panel_off(ctx); > + if (ret < 0) > + dev_err(dev, "Failed to un-initialize panel: %d\n", ret); > + > + gpiod_set_value_cansleep(ctx->reset_gpio, 0); > + regulator_disable(ctx->supply); > + > + ctx->prepared = false; > + return 0; > +} > + > + > +static int oneplus6_panel_enable(struct drm_panel *panel) > +{ > + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); > + int ret; > + > + if (ctx->enabled) > + return 0; > + > + ret = backlight_enable(ctx->backlight); > + if (ret < 0) { > + dev_err(&ctx->dsi->dev, "Failed to enable backlight: %d\n", ret); > + return ret; > + } > + > + ctx->enabled = true; > + return 0; > +} > + > +static int oneplus6_panel_disable(struct drm_panel *panel) > +{ > + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); > + int ret; > + > + if (!ctx->enabled) > + return 0; > + > + ret = backlight_disable(ctx->backlight); > + if (ret < 0) { > + dev_err(&ctx->dsi->dev, "Failed to disable backlight: %d\n", ret); > + return ret; > + } > + > + ctx->enabled = false; > + return 0; > +} When backlight support in drm_panel is used the two enabled/disable functions can be dropped and the enabled flag is then no longer sued and can be dropped too. > + > + > +static const struct drm_display_mode enchilada_panel_mode = { > + .clock = (1080 + 112 + 16 + 36) * (2280 + 36 + 8 + 12) * 60 / 1000, > + .hdisplay = 1080, > + .hsync_start = 1080 + 112, > + .hsync_end = 1080 + 112 + 16, > + .htotal = 1080 + 112 + 16 + 36, > + .vdisplay = 2280, > + .vsync_start = 2280 + 36, > + .vsync_end = 2280 + 36 + 8, > + .vtotal = 2280 + 36 + 8 + 12, > + .width_mm = 68, > + .height_mm = 145, > +}; > + > +static const struct drm_display_mode fajita_panel_mode = { > + .clock = (1080 + 72 + 16 + 36) * (2340 + 32 + 4 + 18) * 60 / 1000, > + .hdisplay = 1080, > + .hsync_start = 1080 + 72, > + .hsync_end = 1080 + 72 + 16, > + .htotal = 1080 + 72 + 16 + 36, > + .vdisplay = 2340, > + .vsync_start = 2340 + 32, > + .vsync_end = 2340 + 32 + 4, > + .vtotal = 2340 + 32 + 4 + 18, > + .width_mm = 68, > + .height_mm = 145, > +}; > + > +static int oneplus6_panel_get_modes(struct drm_panel *panel, > + struct drm_connector *connector) Some indent looks fishy here. Try to check the driver using checkpatch --strict - it should be clean. > +{ > + struct drm_display_mode *mode; > + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); > + > + mode = drm_mode_duplicate(connector->dev, ctx->mode); > + if (!mode) > + return -ENOMEM; > + > + drm_mode_set_name(mode); > + > + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; > + connector->display_info.width_mm = mode->width_mm; > + connector->display_info.height_mm = mode->height_mm; > + drm_mode_probed_add(connector, mode); > + > + return 1; > +} > + > +static const struct drm_panel_funcs oneplus6_panel_panel_funcs = { > + .disable = oneplus6_panel_disable, > + .enable = oneplus6_panel_enable, > + .prepare = oneplus6_panel_prepare, > + .unprepare = oneplus6_panel_unprepare, > + .get_modes = oneplus6_panel_get_modes, > +}; > + > +static int oneplus6_panel_bl_get_brightness(struct backlight_device *bl) > +{ > + struct mipi_dsi_device *dsi = bl_get_data(bl); > + int err; > + u16 brightness = bl->props.brightness; No need to read the brightness here. It will be set if mipi_dsi_dcs_get_display_brightness() succeeds. > + > + err = mipi_dsi_dcs_get_display_brightness(dsi, &brightness); > + if (err < 0) { > + return err; > + } > + > + return brightness & 0xff; > +} > + > +static int oneplus6_panel_bl_update_status(struct backlight_device *bl) > +{ > + struct mipi_dsi_device *dsi = bl_get_data(bl); > + int err; > + unsigned short brightness; > + Use backlight_get_brightness() to get the current brightness from the backlight device. Do not access the properties direct. > + // This panel needs the high and low bytes swapped for the brightness value > + brightness = ((bl->props.brightness<<8)&0xff00)|((bl->props.brightness>>8)&0x00ff); > + > + err = mipi_dsi_dcs_set_display_brightness(dsi, brightness); > + if (err < 0) { > + return err; > + } > + > + return 0; > +} > + > +static const struct backlight_ops oneplus6_panel_bl_ops = { > + .update_status = oneplus6_panel_bl_update_status, > + .get_brightness = oneplus6_panel_bl_get_brightness, > +}; > + > +static struct backlight_device * > +oneplus6_panel_create_backlight(struct mipi_dsi_device *dsi) > +{ > + struct device *dev = &dsi->dev; > + struct backlight_properties props = { const > + .type = BACKLIGHT_PLATFORM, > + .scale = BACKLIGHT_SCALE_LINEAR, > + .brightness = 255, > + .max_brightness = 512, > + }; > + > + return devm_backlight_device_register(dev, dev_name(dev), dev, dsi, > + &oneplus6_panel_bl_ops, &props); > +} > + > + > +static int oneplus6_panel_probe(struct mipi_dsi_device *dsi) > +{ > + struct device *dev = &dsi->dev; > + struct oneplus6_panel *ctx; > + int ret; > + > + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); > + if (!ctx) > + return -ENOMEM; > + > + ctx->mode = of_device_get_match_data(dev); > + > + if (!ctx->mode) { > + dev_err(dev, "Missing device mode\n"); > + return -ENODEV; > + } > + > + ctx->supply = devm_regulator_get(dev, "vddio"); > + if (IS_ERR(ctx->supply)) { > + ret = PTR_ERR(ctx->supply); > + dev_err(dev, "Failed to get vddio regulator: %d\n", ret); > + return ret; > + } > + > + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > + if (IS_ERR(ctx->reset_gpio)) { > + ret = PTR_ERR(ctx->reset_gpio); > + dev_warn(dev, "Failed to get reset-gpios: %d\n", ret); > + return ret; > + } > + > + ctx->backlight = oneplus6_panel_create_backlight(dsi); > + if (IS_ERR(ctx->backlight)) { > + ret = PTR_ERR(ctx->backlight); > + dev_err(dev, "Failed to create backlight: %d\n", ret); > + return ret; > + } > + > + ctx->dsi = dsi; > + mipi_dsi_set_drvdata(dsi, ctx); > + > + dsi->lanes = 4; > + dsi->format = MIPI_DSI_FMT_RGB888; > + > + drm_panel_init(&ctx->panel, dev, &oneplus6_panel_panel_funcs, > + DRM_MODE_CONNECTOR_DSI); > + When using backlight support from drm_panel remember to assing pane-backlight after drm_panel_init() > + ret = drm_panel_add(&ctx->panel); > + if (ret < 0) { > + dev_err(dev, "Failed to add panel: %d\n", ret); > + return ret; > + } > + > + ret = mipi_dsi_attach(dsi); > + if (ret < 0) { > + dev_err(dev, "Failed to attach to DSI host: %d\n", ret); > + return ret; > + } > + > + dev_info(dev, "Successfully added oneplus6 panel"); This is just noide, drop it. > + > + return 0; > +} > + > +static int oneplus6_panel_remove(struct mipi_dsi_device *dsi) > +{ > + struct oneplus6_panel *ctx = mipi_dsi_get_drvdata(dsi); > + int ret; > + > + ret = mipi_dsi_detach(dsi); > + if (ret < 0) > + dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret); > + > + drm_panel_remove(&ctx->panel); > + > + return 0; > +} > + > +static const struct of_device_id oneplus6_panel_of_match[] = { > + { > + .compatible = "samsung,sofef00", > + .data = &enchilada_panel_mode, > + }, > + { > + .compatible = "samsung,s6e3fc2x01", > + .data = &fajita_panel_mode, > + }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, oneplus6_panel_of_match); > + > +static struct mipi_dsi_driver oneplus6_panel_driver = { > + .probe = oneplus6_panel_probe, > + .remove = oneplus6_panel_remove, > + .driver = { > + .name = "panel-oneplus6", > + .of_match_table = oneplus6_panel_of_match, > + }, > +}; > + > +module_mipi_dsi_driver(oneplus6_panel_driver); > + > +MODULE_AUTHOR("Caleb Connolly <caleb@connolly.tech>"); > +MODULE_DESCRIPTION("DRM driver for Samsung AMOLED DSI panels found in OnePlus 6/6T phones"); > +MODULE_LICENSE("GPL v2"); > -- > 2.28.0 >
Hi Sam, Thanks a lot for the feedback! I'll get those issues resolved for the next revision. Caleb On 2020-10-18 14:35, Sam Ravnborg wrote: > Hi Caleb. > > I have missed to provice review feedback so here goes. > There is some improvements that can be made as the infrastructure has > evolved since the driver was started. > But despite the number of comments below it is all trivial and the > driver looks good in general. > > I look forward to see the next revision. > > Sam > > On Wed, Oct 07, 2020 at 05:49:08PM +0000, Caleb Connolly wrote: >> This commit adds support for the display panels used in the OnePlus 6 / >> T devices. >> >> The OnePlus 6/T devices use different panels however they are >> functionally identical with much of the commands being shared. The >> panels don't appear to be used by any other devices some combine them as >> one driver that is specific to the devices. >> >> The panels are: samsung,sofef00 >> and samsung,s6e3fc2x01 >> >> Signed-off-by: Caleb Connolly <caleb@connolly.tech> >> --- >> drivers/gpu/drm/panel/Kconfig | 12 + >> drivers/gpu/drm/panel/Makefile | 1 + >> drivers/gpu/drm/panel/panel-oneplus6.c | 418 +++++++++++++++++++++++++ > It would be better to name the driver after the panels and not their > user. So something like panel-samsung-sofef00. > It is OK to name it after one panel and let it support mroe than one > panel. The Kconfig description could then expain where it is used. > > >> 3 files changed, 431 insertions(+) >> create mode 100644 drivers/gpu/drm/panel/panel-oneplus6.c >> >> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig >> index de2f2a452be5..d72862265400 100644 >> --- a/drivers/gpu/drm/panel/Kconfig >> +++ b/drivers/gpu/drm/panel/Kconfig >> @@ -229,6 +229,18 @@ config DRM_PANEL_OLIMEX_LCD_OLINUXINO >> Say Y here if you want to enable support for Olimex Ltd. >> LCD-OLinuXino panel. >> >> +config DRM_PANEL_ONEPLUS6 >> + tristate "OnePlus 6/6T Samsung AMOLED DSI command mode panels" >> + depends on OF >> + depends on DRM_MIPI_DSI >> + depends on BACKLIGHT_CLASS_DEVICE >> + select VIDEOMODE_HELPERS >> + help >> + Say Y or M here if you want to enable support for the Samsung AMOLED >> + command mode panels found in the OnePlus 6/6T smartphones. >> + >> + The panels are 2280x1080@60Hz and 2340x1080@60Hz respectively >> + >> config DRM_PANEL_ORISETECH_OTM8009A >> tristate "Orise Technology otm8009a 480x800 dsi 2dl panel" >> depends on OF >> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile >> index e45ceac6286f..017539056f53 100644 >> --- a/drivers/gpu/drm/panel/Makefile >> +++ b/drivers/gpu/drm/panel/Makefile >> @@ -21,6 +21,7 @@ obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o >> obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o >> obj-$(CONFIG_DRM_PANEL_NOVATEK_NT39016) += panel-novatek-nt39016.o >> obj-$(CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO) += panel-olimex-lcd-olinuxino.o >> +obj-$(CONFIG_DRM_PANEL_ONEPLUS6) += panel-oneplus6.o >> obj-$(CONFIG_DRM_PANEL_ORISETECH_OTM8009A) += panel-orisetech-otm8009a.o >> obj-$(CONFIG_DRM_PANEL_OSD_OSD101T2587_53TS) += panel-osd-osd101t2587-53ts.o >> obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o >> diff --git a/drivers/gpu/drm/panel/panel-oneplus6.c b/drivers/gpu/drm/panel/panel-oneplus6.c >> new file mode 100644 >> index 000000000000..5e212774b1e0 >> --- /dev/null >> +++ b/drivers/gpu/drm/panel/panel-oneplus6.c >> @@ -0,0 +1,418 @@ >> +// SPDX-License-Identifier: GPL-2.0-only >> +/* Copyright (c) 2020 Caleb Connolly <caleb@connolly.tech> >> + * Generated with linux-mdss-dsi-panel-driver-generator from vendor device tree: >> + * Copyright (c) 2020, The Linux Foundation. All rights reserved. >> + * >> + * Caleb Connolly <caleb@connolly.tech> >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/gpio/consumer.h> >> +#include <linux/module.h> >> +#include <linux/of.h> >> +#include <linux/of_device.h> >> +#include <linux/regulator/consumer.h> >> + >> +#include <video/mipi_display.h> >> + >> +#include <drm/drm_mipi_dsi.h> >> +#include <drm/drm_modes.h> >> +#include <drm/drm_panel.h> >> +#include <linux/backlight.h> > Keep all linux include together. > >> + >> +struct oneplus6_panel { >> + struct drm_panel panel; >> + struct mipi_dsi_device *dsi; >> + struct backlight_device *backlight; > Use drm_panel backlight support - so you can drop this variable and > simplify some of the code below. > >> + struct regulator *supply; >> + struct gpio_desc *reset_gpio; >> + struct gpio_desc *enable_gpio; > The enable_gpio is not used. > >> + const struct drm_display_mode *mode; >> + bool prepared; >> + bool enabled; >> +}; >> + >> +static inline >> +struct oneplus6_panel *to_oneplus6_panel(struct drm_panel *panel) >> +{ >> + return container_of(panel, struct oneplus6_panel, panel); >> +} >> + >> +#define dsi_dcs_write_seq(dsi, seq...) do { \ >> + static const u8 d[] = { seq }; \ >> + int ret; \ >> + ret = mipi_dsi_dcs_write_buffer(dsi, d, ARRAY_SIZE(d)); \ >> + if (ret < 0) \ >> + return ret; \ >> + } while (0) >> + >> +static void oneplus6_panel_reset(struct oneplus6_panel *ctx) >> +{ >> + gpiod_set_value_cansleep(ctx->reset_gpio, 1); >> + usleep_range(5000, 6000); >> +} > IT is not obvious if this helper reset the panel or de-assert the reset > signal. It does not help me that there is only one helper despite both > operatiosn are needed. > >> + >> +static int oneplus6_panel_on(struct oneplus6_panel *ctx) >> +{ >> + struct mipi_dsi_device *dsi = ctx->dsi; >> + struct device *dev = &dsi->dev; >> + int ret; >> + >> + dsi->mode_flags |= MIPI_DSI_MODE_LPM; >> + >> + ret = mipi_dsi_dcs_exit_sleep_mode(dsi); >> + if (ret < 0) { >> + dev_err(dev, "Failed to exit sleep mode: %d\n", ret); >> + return ret; >> + } >> + usleep_range(10000, 11000); >> + >> + dsi_dcs_write_seq(dsi, 0xf0, 0x5a, 0x5a); >> + >> + ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK); >> + if (ret < 0) { >> + dev_err(dev, "Failed to set tear on: %d\n", ret); >> + return ret; >> + } >> + >> + dsi_dcs_write_seq(dsi, 0xf0, 0xa5, 0xa5); >> + dsi_dcs_write_seq(dsi, 0xf0, 0x5a, 0x5a); >> + dsi_dcs_write_seq(dsi, 0xb0, 0x07); >> + dsi_dcs_write_seq(dsi, 0xb6, 0x12); >> + dsi_dcs_write_seq(dsi, 0xf0, 0xa5, 0xa5); >> + dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x20); >> + dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_POWER_SAVE, 0x00); >> + >> + ret = mipi_dsi_dcs_set_display_on(dsi); >> + if (ret < 0) { >> + dev_err(dev, "Failed to set display on: %d\n", ret); >> + return ret; >> + } >> + >> + return 0; >> +} >> + >> +static int oneplus6_panel_off(struct oneplus6_panel *ctx) >> +{ >> + struct mipi_dsi_device *dsi = ctx->dsi; >> + struct device *dev = &dsi->dev; >> + int ret; >> + >> + dsi->mode_flags &= ~MIPI_DSI_MODE_LPM; >> + >> + ret = mipi_dsi_dcs_set_display_off(dsi); >> + if (ret < 0) { >> + dev_err(dev, "Failed to set display off: %d\n", ret); >> + return ret; >> + } >> + msleep(40); >> + >> + ret = mipi_dsi_dcs_enter_sleep_mode(dsi); >> + if (ret < 0) { >> + dev_err(dev, "Failed to enter sleep mode: %d\n", ret); >> + return ret; >> + } >> + msleep(160); >> + >> + return 0; >> +} >> + >> +static int oneplus6_panel_prepare(struct drm_panel *panel) >> +{ >> + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); >> + struct device *dev = &ctx->dsi->dev; >> + int ret; >> + >> + if (ctx->prepared) >> + return 0; >> + > Do you not need to do a regulator_enable() here to get power supply to > the panel? > >> + oneplus6_panel_reset(ctx); >> + >> + ret = oneplus6_panel_on(ctx); >> + if (ret < 0) { >> + dev_err(dev, "Failed to initialize panel: %d\n", ret); >> + gpiod_set_value_cansleep(ctx->reset_gpio, 0); >> + return ret; >> + } >> + >> + ctx->prepared = true; >> + return 0; >> +} >> + >> +static int oneplus6_panel_unprepare(struct drm_panel *panel) >> +{ >> + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); >> + struct device *dev = &ctx->dsi->dev; >> + int ret; >> + >> + if (!ctx->prepared) >> + return 0; >> + >> + ret = regulator_enable(ctx->supply); > Looks strange that the power supply is enabled here - was it not enabled > before to use the panel? > >> + if (ret < 0) { >> + dev_err(dev, "Failed to enable regulator: %d\n", ret); >> + return ret; >> + } >> + >> + ret = oneplus6_panel_off(ctx); >> + if (ret < 0) >> + dev_err(dev, "Failed to un-initialize panel: %d\n", ret); >> + >> + gpiod_set_value_cansleep(ctx->reset_gpio, 0); >> + regulator_disable(ctx->supply); >> + >> + ctx->prepared = false; >> + return 0; >> +} >> + >> + >> +static int oneplus6_panel_enable(struct drm_panel *panel) >> +{ >> + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); >> + int ret; >> + >> + if (ctx->enabled) >> + return 0; >> + >> + ret = backlight_enable(ctx->backlight); >> + if (ret < 0) { >> + dev_err(&ctx->dsi->dev, "Failed to enable backlight: %d\n", ret); >> + return ret; >> + } >> + >> + ctx->enabled = true; >> + return 0; >> +} >> + >> +static int oneplus6_panel_disable(struct drm_panel *panel) >> +{ >> + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); >> + int ret; >> + >> + if (!ctx->enabled) >> + return 0; >> + >> + ret = backlight_disable(ctx->backlight); >> + if (ret < 0) { >> + dev_err(&ctx->dsi->dev, "Failed to disable backlight: %d\n", ret); >> + return ret; >> + } >> + >> + ctx->enabled = false; >> + return 0; >> +} > When backlight support in drm_panel is used the two enabled/disable > functions can be dropped and the enabled flag is then no longer sued and > can be dropped too. > >> + >> + >> +static const struct drm_display_mode enchilada_panel_mode = { >> + .clock = (1080 + 112 + 16 + 36) * (2280 + 36 + 8 + 12) * 60 / 1000, >> + .hdisplay = 1080, >> + .hsync_start = 1080 + 112, >> + .hsync_end = 1080 + 112 + 16, >> + .htotal = 1080 + 112 + 16 + 36, >> + .vdisplay = 2280, >> + .vsync_start = 2280 + 36, >> + .vsync_end = 2280 + 36 + 8, >> + .vtotal = 2280 + 36 + 8 + 12, >> + .width_mm = 68, >> + .height_mm = 145, >> +}; >> + >> +static const struct drm_display_mode fajita_panel_mode = { >> + .clock = (1080 + 72 + 16 + 36) * (2340 + 32 + 4 + 18) * 60 / 1000, >> + .hdisplay = 1080, >> + .hsync_start = 1080 + 72, >> + .hsync_end = 1080 + 72 + 16, >> + .htotal = 1080 + 72 + 16 + 36, >> + .vdisplay = 2340, >> + .vsync_start = 2340 + 32, >> + .vsync_end = 2340 + 32 + 4, >> + .vtotal = 2340 + 32 + 4 + 18, >> + .width_mm = 68, >> + .height_mm = 145, >> +}; >> + >> +static int oneplus6_panel_get_modes(struct drm_panel *panel, >> + struct drm_connector *connector) > Some indent looks fishy here. > Try to check the driver using checkpatch --strict - it should be clean. >> +{ >> + struct drm_display_mode *mode; >> + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); >> + >> + mode = drm_mode_duplicate(connector->dev, ctx->mode); >> + if (!mode) >> + return -ENOMEM; >> + >> + drm_mode_set_name(mode); >> + >> + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; >> + connector->display_info.width_mm = mode->width_mm; >> + connector->display_info.height_mm = mode->height_mm; >> + drm_mode_probed_add(connector, mode); >> + >> + return 1; >> +} >> + >> +static const struct drm_panel_funcs oneplus6_panel_panel_funcs = { >> + .disable = oneplus6_panel_disable, >> + .enable = oneplus6_panel_enable, >> + .prepare = oneplus6_panel_prepare, >> + .unprepare = oneplus6_panel_unprepare, >> + .get_modes = oneplus6_panel_get_modes, >> +}; >> + >> +static int oneplus6_panel_bl_get_brightness(struct backlight_device *bl) >> +{ >> + struct mipi_dsi_device *dsi = bl_get_data(bl); >> + int err; >> + u16 brightness = bl->props.brightness; > No need to read the brightness here. It will be set if > mipi_dsi_dcs_get_display_brightness() succeeds. >> + >> + err = mipi_dsi_dcs_get_display_brightness(dsi, &brightness); >> + if (err < 0) { >> + return err; >> + } >> + >> + return brightness & 0xff; >> +} >> + >> +static int oneplus6_panel_bl_update_status(struct backlight_device *bl) >> +{ >> + struct mipi_dsi_device *dsi = bl_get_data(bl); >> + int err; >> + unsigned short brightness; >> + > Use backlight_get_brightness() to get the current brightness from the > backlight device. Do not access the properties direct. >> + // This panel needs the high and low bytes swapped for the brightness value >> + brightness = ((bl->props.brightness<<8)&0xff00)|((bl->props.brightness>>8)&0x00ff); >> + >> + err = mipi_dsi_dcs_set_display_brightness(dsi, brightness); >> + if (err < 0) { >> + return err; >> + } >> + >> + return 0; >> +} >> + >> +static const struct backlight_ops oneplus6_panel_bl_ops = { >> + .update_status = oneplus6_panel_bl_update_status, >> + .get_brightness = oneplus6_panel_bl_get_brightness, >> +}; >> + >> +static struct backlight_device * >> +oneplus6_panel_create_backlight(struct mipi_dsi_device *dsi) >> +{ >> + struct device *dev = &dsi->dev; >> + struct backlight_properties props = { > const >> + .type = BACKLIGHT_PLATFORM, >> + .scale = BACKLIGHT_SCALE_LINEAR, >> + .brightness = 255, >> + .max_brightness = 512, >> + }; >> + >> + return devm_backlight_device_register(dev, dev_name(dev), dev, dsi, >> + &oneplus6_panel_bl_ops, &props); >> +} >> + >> + >> +static int oneplus6_panel_probe(struct mipi_dsi_device *dsi) >> +{ >> + struct device *dev = &dsi->dev; >> + struct oneplus6_panel *ctx; >> + int ret; >> + >> + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); >> + if (!ctx) >> + return -ENOMEM; >> + >> + ctx->mode = of_device_get_match_data(dev); >> + >> + if (!ctx->mode) { >> + dev_err(dev, "Missing device mode\n"); >> + return -ENODEV; >> + } >> + >> + ctx->supply = devm_regulator_get(dev, "vddio"); >> + if (IS_ERR(ctx->supply)) { >> + ret = PTR_ERR(ctx->supply); >> + dev_err(dev, "Failed to get vddio regulator: %d\n", ret); >> + return ret; >> + } >> + >> + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); >> + if (IS_ERR(ctx->reset_gpio)) { >> + ret = PTR_ERR(ctx->reset_gpio); >> + dev_warn(dev, "Failed to get reset-gpios: %d\n", ret); >> + return ret; >> + } >> + >> + ctx->backlight = oneplus6_panel_create_backlight(dsi); >> + if (IS_ERR(ctx->backlight)) { >> + ret = PTR_ERR(ctx->backlight); >> + dev_err(dev, "Failed to create backlight: %d\n", ret); >> + return ret; >> + } >> + >> + ctx->dsi = dsi; >> + mipi_dsi_set_drvdata(dsi, ctx); >> + >> + dsi->lanes = 4; >> + dsi->format = MIPI_DSI_FMT_RGB888; >> + >> + drm_panel_init(&ctx->panel, dev, &oneplus6_panel_panel_funcs, >> + DRM_MODE_CONNECTOR_DSI); >> + > When using backlight support from drm_panel remember to assing > pane-backlight after drm_panel_init() > >> + ret = drm_panel_add(&ctx->panel); >> + if (ret < 0) { >> + dev_err(dev, "Failed to add panel: %d\n", ret); >> + return ret; >> + } >> + >> + ret = mipi_dsi_attach(dsi); >> + if (ret < 0) { >> + dev_err(dev, "Failed to attach to DSI host: %d\n", ret); >> + return ret; >> + } >> + >> + dev_info(dev, "Successfully added oneplus6 panel"); > This is just noide, drop it. >> + >> + return 0; >> +} >> + >> +static int oneplus6_panel_remove(struct mipi_dsi_device *dsi) >> +{ >> + struct oneplus6_panel *ctx = mipi_dsi_get_drvdata(dsi); >> + int ret; >> + >> + ret = mipi_dsi_detach(dsi); >> + if (ret < 0) >> + dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret); >> + >> + drm_panel_remove(&ctx->panel); >> + >> + return 0; >> +} >> + >> +static const struct of_device_id oneplus6_panel_of_match[] = { >> + { >> + .compatible = "samsung,sofef00", >> + .data = &enchilada_panel_mode, >> + }, >> + { >> + .compatible = "samsung,s6e3fc2x01", >> + .data = &fajita_panel_mode, >> + }, >> + { /* sentinel */ } >> +}; >> +MODULE_DEVICE_TABLE(of, oneplus6_panel_of_match); >> + >> +static struct mipi_dsi_driver oneplus6_panel_driver = { >> + .probe = oneplus6_panel_probe, >> + .remove = oneplus6_panel_remove, >> + .driver = { >> + .name = "panel-oneplus6", >> + .of_match_table = oneplus6_panel_of_match, >> + }, >> +}; >> + >> +module_mipi_dsi_driver(oneplus6_panel_driver); >> + >> +MODULE_AUTHOR("Caleb Connolly <caleb@connolly.tech>"); >> +MODULE_DESCRIPTION("DRM driver for Samsung AMOLED DSI panels found in OnePlus 6/6T phones"); >> +MODULE_LICENSE("GPL v2"); >> -- >> 2.28.0 >>
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index de2f2a452be5..d72862265400 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -229,6 +229,18 @@ config DRM_PANEL_OLIMEX_LCD_OLINUXINO Say Y here if you want to enable support for Olimex Ltd. LCD-OLinuXino panel. +config DRM_PANEL_ONEPLUS6 + tristate "OnePlus 6/6T Samsung AMOLED DSI command mode panels" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + select VIDEOMODE_HELPERS + help + Say Y or M here if you want to enable support for the Samsung AMOLED + command mode panels found in the OnePlus 6/6T smartphones. + + The panels are 2280x1080@60Hz and 2340x1080@60Hz respectively + config DRM_PANEL_ORISETECH_OTM8009A tristate "Orise Technology otm8009a 480x800 dsi 2dl panel" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index e45ceac6286f..017539056f53 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -21,6 +21,7 @@ obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o obj-$(CONFIG_DRM_PANEL_NOVATEK_NT39016) += panel-novatek-nt39016.o obj-$(CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO) += panel-olimex-lcd-olinuxino.o +obj-$(CONFIG_DRM_PANEL_ONEPLUS6) += panel-oneplus6.o obj-$(CONFIG_DRM_PANEL_ORISETECH_OTM8009A) += panel-orisetech-otm8009a.o obj-$(CONFIG_DRM_PANEL_OSD_OSD101T2587_53TS) += panel-osd-osd101t2587-53ts.o obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o diff --git a/drivers/gpu/drm/panel/panel-oneplus6.c b/drivers/gpu/drm/panel/panel-oneplus6.c new file mode 100644 index 000000000000..5e212774b1e0 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-oneplus6.c @@ -0,0 +1,418 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* Copyright (c) 2020 Caleb Connolly <caleb@connolly.tech> + * Generated with linux-mdss-dsi-panel-driver-generator from vendor device tree: + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + * + * Caleb Connolly <caleb@connolly.tech> + */ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <linux/backlight.h> + +struct oneplus6_panel { + struct drm_panel panel; + struct mipi_dsi_device *dsi; + struct backlight_device *backlight; + struct regulator *supply; + struct gpio_desc *reset_gpio; + struct gpio_desc *enable_gpio; + const struct drm_display_mode *mode; + bool prepared; + bool enabled; +}; + +static inline +struct oneplus6_panel *to_oneplus6_panel(struct drm_panel *panel) +{ + return container_of(panel, struct oneplus6_panel, panel); +} + +#define dsi_dcs_write_seq(dsi, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = mipi_dsi_dcs_write_buffer(dsi, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ + } while (0) + +static void oneplus6_panel_reset(struct oneplus6_panel *ctx) +{ + gpiod_set_value_cansleep(ctx->reset_gpio, 1); + usleep_range(5000, 6000); +} + +static int oneplus6_panel_on(struct oneplus6_panel *ctx) +{ + struct mipi_dsi_device *dsi = ctx->dsi; + struct device *dev = &dsi->dev; + int ret; + + dsi->mode_flags |= MIPI_DSI_MODE_LPM; + + ret = mipi_dsi_dcs_exit_sleep_mode(dsi); + if (ret < 0) { + dev_err(dev, "Failed to exit sleep mode: %d\n", ret); + return ret; + } + usleep_range(10000, 11000); + + dsi_dcs_write_seq(dsi, 0xf0, 0x5a, 0x5a); + + ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK); + if (ret < 0) { + dev_err(dev, "Failed to set tear on: %d\n", ret); + return ret; + } + + dsi_dcs_write_seq(dsi, 0xf0, 0xa5, 0xa5); + dsi_dcs_write_seq(dsi, 0xf0, 0x5a, 0x5a); + dsi_dcs_write_seq(dsi, 0xb0, 0x07); + dsi_dcs_write_seq(dsi, 0xb6, 0x12); + dsi_dcs_write_seq(dsi, 0xf0, 0xa5, 0xa5); + dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x20); + dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_POWER_SAVE, 0x00); + + ret = mipi_dsi_dcs_set_display_on(dsi); + if (ret < 0) { + dev_err(dev, "Failed to set display on: %d\n", ret); + return ret; + } + + return 0; +} + +static int oneplus6_panel_off(struct oneplus6_panel *ctx) +{ + struct mipi_dsi_device *dsi = ctx->dsi; + struct device *dev = &dsi->dev; + int ret; + + dsi->mode_flags &= ~MIPI_DSI_MODE_LPM; + + ret = mipi_dsi_dcs_set_display_off(dsi); + if (ret < 0) { + dev_err(dev, "Failed to set display off: %d\n", ret); + return ret; + } + msleep(40); + + ret = mipi_dsi_dcs_enter_sleep_mode(dsi); + if (ret < 0) { + dev_err(dev, "Failed to enter sleep mode: %d\n", ret); + return ret; + } + msleep(160); + + return 0; +} + +static int oneplus6_panel_prepare(struct drm_panel *panel) +{ + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); + struct device *dev = &ctx->dsi->dev; + int ret; + + if (ctx->prepared) + return 0; + + oneplus6_panel_reset(ctx); + + ret = oneplus6_panel_on(ctx); + if (ret < 0) { + dev_err(dev, "Failed to initialize panel: %d\n", ret); + gpiod_set_value_cansleep(ctx->reset_gpio, 0); + return ret; + } + + ctx->prepared = true; + return 0; +} + +static int oneplus6_panel_unprepare(struct drm_panel *panel) +{ + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); + struct device *dev = &ctx->dsi->dev; + int ret; + + if (!ctx->prepared) + return 0; + + ret = regulator_enable(ctx->supply); + if (ret < 0) { + dev_err(dev, "Failed to enable regulator: %d\n", ret); + return ret; + } + + ret = oneplus6_panel_off(ctx); + if (ret < 0) + dev_err(dev, "Failed to un-initialize panel: %d\n", ret); + + gpiod_set_value_cansleep(ctx->reset_gpio, 0); + regulator_disable(ctx->supply); + + ctx->prepared = false; + return 0; +} + + +static int oneplus6_panel_enable(struct drm_panel *panel) +{ + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); + int ret; + + if (ctx->enabled) + return 0; + + ret = backlight_enable(ctx->backlight); + if (ret < 0) { + dev_err(&ctx->dsi->dev, "Failed to enable backlight: %d\n", ret); + return ret; + } + + ctx->enabled = true; + return 0; +} + +static int oneplus6_panel_disable(struct drm_panel *panel) +{ + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); + int ret; + + if (!ctx->enabled) + return 0; + + ret = backlight_disable(ctx->backlight); + if (ret < 0) { + dev_err(&ctx->dsi->dev, "Failed to disable backlight: %d\n", ret); + return ret; + } + + ctx->enabled = false; + return 0; +} + + +static const struct drm_display_mode enchilada_panel_mode = { + .clock = (1080 + 112 + 16 + 36) * (2280 + 36 + 8 + 12) * 60 / 1000, + .hdisplay = 1080, + .hsync_start = 1080 + 112, + .hsync_end = 1080 + 112 + 16, + .htotal = 1080 + 112 + 16 + 36, + .vdisplay = 2280, + .vsync_start = 2280 + 36, + .vsync_end = 2280 + 36 + 8, + .vtotal = 2280 + 36 + 8 + 12, + .width_mm = 68, + .height_mm = 145, +}; + +static const struct drm_display_mode fajita_panel_mode = { + .clock = (1080 + 72 + 16 + 36) * (2340 + 32 + 4 + 18) * 60 / 1000, + .hdisplay = 1080, + .hsync_start = 1080 + 72, + .hsync_end = 1080 + 72 + 16, + .htotal = 1080 + 72 + 16 + 36, + .vdisplay = 2340, + .vsync_start = 2340 + 32, + .vsync_end = 2340 + 32 + 4, + .vtotal = 2340 + 32 + 4 + 18, + .width_mm = 68, + .height_mm = 145, +}; + +static int oneplus6_panel_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct drm_display_mode *mode; + struct oneplus6_panel *ctx = to_oneplus6_panel(panel); + + mode = drm_mode_duplicate(connector->dev, ctx->mode); + if (!mode) + return -ENOMEM; + + drm_mode_set_name(mode); + + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; + drm_mode_probed_add(connector, mode); + + return 1; +} + +static const struct drm_panel_funcs oneplus6_panel_panel_funcs = { + .disable = oneplus6_panel_disable, + .enable = oneplus6_panel_enable, + .prepare = oneplus6_panel_prepare, + .unprepare = oneplus6_panel_unprepare, + .get_modes = oneplus6_panel_get_modes, +}; + +static int oneplus6_panel_bl_get_brightness(struct backlight_device *bl) +{ + struct mipi_dsi_device *dsi = bl_get_data(bl); + int err; + u16 brightness = bl->props.brightness; + + err = mipi_dsi_dcs_get_display_brightness(dsi, &brightness); + if (err < 0) { + return err; + } + + return brightness & 0xff; +} + +static int oneplus6_panel_bl_update_status(struct backlight_device *bl) +{ + struct mipi_dsi_device *dsi = bl_get_data(bl); + int err; + unsigned short brightness; + + // This panel needs the high and low bytes swapped for the brightness value + brightness = ((bl->props.brightness<<8)&0xff00)|((bl->props.brightness>>8)&0x00ff); + + err = mipi_dsi_dcs_set_display_brightness(dsi, brightness); + if (err < 0) { + return err; + } + + return 0; +} + +static const struct backlight_ops oneplus6_panel_bl_ops = { + .update_status = oneplus6_panel_bl_update_status, + .get_brightness = oneplus6_panel_bl_get_brightness, +}; + +static struct backlight_device * +oneplus6_panel_create_backlight(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct backlight_properties props = { + .type = BACKLIGHT_PLATFORM, + .scale = BACKLIGHT_SCALE_LINEAR, + .brightness = 255, + .max_brightness = 512, + }; + + return devm_backlight_device_register(dev, dev_name(dev), dev, dsi, + &oneplus6_panel_bl_ops, &props); +} + + +static int oneplus6_panel_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct oneplus6_panel *ctx; + int ret; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + ctx->mode = of_device_get_match_data(dev); + + if (!ctx->mode) { + dev_err(dev, "Missing device mode\n"); + return -ENODEV; + } + + ctx->supply = devm_regulator_get(dev, "vddio"); + if (IS_ERR(ctx->supply)) { + ret = PTR_ERR(ctx->supply); + dev_err(dev, "Failed to get vddio regulator: %d\n", ret); + return ret; + } + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(ctx->reset_gpio)) { + ret = PTR_ERR(ctx->reset_gpio); + dev_warn(dev, "Failed to get reset-gpios: %d\n", ret); + return ret; + } + + ctx->backlight = oneplus6_panel_create_backlight(dsi); + if (IS_ERR(ctx->backlight)) { + ret = PTR_ERR(ctx->backlight); + dev_err(dev, "Failed to create backlight: %d\n", ret); + return ret; + } + + ctx->dsi = dsi; + mipi_dsi_set_drvdata(dsi, ctx); + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + + drm_panel_init(&ctx->panel, dev, &oneplus6_panel_panel_funcs, + DRM_MODE_CONNECTOR_DSI); + + ret = drm_panel_add(&ctx->panel); + if (ret < 0) { + dev_err(dev, "Failed to add panel: %d\n", ret); + return ret; + } + + ret = mipi_dsi_attach(dsi); + if (ret < 0) { + dev_err(dev, "Failed to attach to DSI host: %d\n", ret); + return ret; + } + + dev_info(dev, "Successfully added oneplus6 panel"); + + return 0; +} + +static int oneplus6_panel_remove(struct mipi_dsi_device *dsi) +{ + struct oneplus6_panel *ctx = mipi_dsi_get_drvdata(dsi); + int ret; + + ret = mipi_dsi_detach(dsi); + if (ret < 0) + dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret); + + drm_panel_remove(&ctx->panel); + + return 0; +} + +static const struct of_device_id oneplus6_panel_of_match[] = { + { + .compatible = "samsung,sofef00", + .data = &enchilada_panel_mode, + }, + { + .compatible = "samsung,s6e3fc2x01", + .data = &fajita_panel_mode, + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, oneplus6_panel_of_match); + +static struct mipi_dsi_driver oneplus6_panel_driver = { + .probe = oneplus6_panel_probe, + .remove = oneplus6_panel_remove, + .driver = { + .name = "panel-oneplus6", + .of_match_table = oneplus6_panel_of_match, + }, +}; + +module_mipi_dsi_driver(oneplus6_panel_driver); + +MODULE_AUTHOR("Caleb Connolly <caleb@connolly.tech>"); +MODULE_DESCRIPTION("DRM driver for Samsung AMOLED DSI panels found in OnePlus 6/6T phones"); +MODULE_LICENSE("GPL v2");
This commit adds support for the display panels used in the OnePlus 6 / T devices. The OnePlus 6/T devices use different panels however they are functionally identical with much of the commands being shared. The panels don't appear to be used by any other devices some combine them as one driver that is specific to the devices. The panels are: samsung,sofef00 and samsung,s6e3fc2x01 Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-oneplus6.c | 418 +++++++++++++++++++++++++ 3 files changed, 431 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-oneplus6.c