[v6,2/8] doc: Add documentation for Coresight CPU debug

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index facc20a..cf90146 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -650,6 +650,13 @@ 
 			/proc/<pid>/coredump_filter.
 			See also Documentation/filesystems/proc.txt.
 
+	coresight_cpu_debug.enable
+			[ARM,ARM64]
+			Format: <bool>
+			Enable/disable the CPU sampling based debugging.
+			0: default value, disable debugging
+			1: enable debugging at boot time
+
 	cpuidle.off=1	[CPU_IDLE]
 			disable the cpuidle sub-system
 
diff --git a/Documentation/trace/coresight-cpu-debug.txt b/Documentation/trace/coresight-cpu-debug.txt
new file mode 100644
index 0000000..e7ad05e
--- /dev/null
+++ b/Documentation/trace/coresight-cpu-debug.txt
@@ -0,0 +1,173 @@ 
+		Coresight CPU Debug Module
+		==========================
+
+   Author:   Leo Yan <leo.yan@linaro.org>
+   Date:     April 5th, 2017
+
+Introduction
+------------
+
+Coresight CPU debug module is defined in ARMv8-a architecture reference manual
+(ARM DDI 0487A.k) Chapter 'Part H: External debug', the CPU can integrate
+debug module and it is mainly used for two modes: self-hosted debug and
+external debug. Usually the external debug mode is well known as the external
+debugger connects with SoC from JTAG port; on the other hand the program can
+explore debugging method which rely on self-hosted debug mode, this document
+is to focus on this part.
+
+The debug module provides sample-based profiling extension, which can be used
+to sample CPU program counter, secure state and exception level, etc; usually
+every CPU has one dedicated debug module to be connected. Based on self-hosted
+debug mechanism, Linux kernel can access these related registers from mmio
+region when the kernel panic happens. The callback notifier for kernel panic
+will dump related registers for every CPU; finally this is good for assistant
+analysis for panic.
+
+
+Implementation
+--------------
+
+- During driver registration, use EDDEVID and EDDEVID1 two device ID
+  registers to decide if sample-based profiling is implemented or not. On some
+  platforms this hardware feature is fully or partialy implemented; and if
+  this feature is not supported then registration will fail.
+
+- When write this doc, the debug driver mainly relies on three sampling
+  registers. The kernel panic callback notifier gathers info from EDPCSR
+  EDVIDSR and EDCIDSR; from EDPCSR we can get program counter, EDVIDSR has
+  information for secure state, exception level, bit width, etc; EDCIDSR is
+  context ID value which contains the sampled value of CONTEXTIDR_EL1.
+
+- The driver supports CPU running mode with either AArch64 or AArch32. The
+  registers naming convention is a bit different between them, AArch64 uses
+  'ED' for register prefix (ARM DDI 0487A.k, chapter H9.1) and AArch32 uses
+  'DBG' as prefix (ARM DDI 0487A.k, chapter G5.1). The driver is unified to
+  use AArch64 naming convention.
+
+- ARMv8-a (ARM DDI 0487A.k) and ARMv7-a (ARM DDI 0406C.b) have different
+  register bits definition. So the driver consolidates two difference:
+
+  If PCSROffset=0b0000. ARMv8-a doesn't apply offset on PCSR, but ARMv7-a
+  defines "PCSR samples are offset by a value that depends on the instruction
+  set state". For ARMv7-a, the driver checks furthermore if CPU runs with ARM
+  or thumb instruction set and calibrate PCSR value, the detailed description
+  for offset is in ARMv7-a ARM (ARM DDI 0406C.b) chapter C11.11.34 "DBGPCSR,
+  Program Counter Sampling Register".
+
+  If PCSROffset=0b0010, ARMv8-a defines "EDPCSR implemented, and samples have
+  no offset applied and do not sample the instruction set state in AArch32
+  state". So for the case when CPU runs with AArch32 state and PCSROffset=
+  0b0010, the driver considers PCSR doesn't really work.
+
+
+Clock and power domain
+----------------------
+
+Before accessing debug registers, we should ensure the clock and power domain
+have been enabled properly. In ARMv8-a ARM (ARM DDI 0487A.k) chapter 'H9.1
+Debug registers', the debug registers are spread into two domains: the debug
+domain and the CPU domain.
+
+                                +---------------+
+                                |               |
+                                |               |
+                     +----------+--+            |
+          dbg_clk -->|          |**|            |<-- cpu_clk
+                     |    Debug |**|   CPU      |
+           dbg_pd -->|          |**|            |<-- cpu_pd
+                     +----------+--+            |
+                                |               |
+                                |               |
+                                +---------------+
+
+For debug domain, the user uses DT binding "clocks" and "power-domains" to
+specify the corresponding clock source and power supply for the debug logic.
+The driver calls the pm_runtime_{put|get} operations as needed to handle the
+debug power domain.
+
+For CPU domain, the different SoC designs have different power management
+schemes and finally this heavily impacts external debug module. So we can
+divide into below cases:
+
+- On systems with a sane power controller which can behave correctly with
+  respect to CPU power domain, the CPU power domain can be controlled by
+  register EDPRCR in driver. The driver firstly writes bit EDPRCR.COREPURQ
+  to power up the CPU, and then writes bit EDPRCR.CORENPDRQ for emulation
+  of CPU power down. As result, this can ensure the CPU power domain is
+  powered on properly during the period when access debug related registers;
+
+- Some designs will power down an entire cluster if all CPUs on the cluster
+  are powered down - including the parts of the debug registers that should
+  remain powered in the debug power domain. The bits in EDPRCR are not
+  respected in these cases, so these designs do not really support debug over
+  power down in the way that the CoreSight / Debug designers anticipated.
+  This means that even checking EDPRSR has the potential to cause a bus hang
+  if the target register is unpowered.
+
+  In this case, accessing to the debug registers while they are not powered
+  is a recipe for disaster; so we need preventing CPU low power states at boot
+  time or when user enable module at the run time. Please see chapter
+  "How to use the module" for detailed usage info for this.
+
+
+Device Tree Bindings
+--------------------
+
+See Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt for details.
+
+
+How to use the module
+---------------------
+
+If you want to enable debugging functionality at boot time, you can add
+"coresight_cpu_debug.enable=1" to the kernel command line parameter.
+
+The driver also can work as module, so can enable the debugging when insmod
+module:
+# insmod coresight_cpu_debug.ko debug=1
+
+When boot time or insmod module you have not enabled the debugging, the driver
+uses the debugfs file system to provide a knob to dynamically enable or disable
+debugging:
+
+To enable it, write a '1' into /sys/kernel/debug/coresight_cpu_debug/enable:
+# echo 1 > /sys/kernel/debug/coresight_cpu_debug/enable
+
+To disable it, write a '0' into /sys/kernel/debug/coresight_cpu_debug/enable:
+# echo 0 > /sys/kernel/debug/coresight_cpu_debug/enable
+
+As explained in chapter "Clock and power domain", if you are working on one
+platform which has idle states to power off debug logic and the power
+controller cannot work well for the request from EDPRCR, then you should
+firstly constraint CPU idle states before enable CPU debugging feature; so can
+ensure the accessing to debug logic.
+
+If you want to limit idle states at boot time, you can use "nohlt" or
+"cpuidle.off=1" in the kernel command line.
+
+At the runtime you can disable idle states with below methods:
+
+Set latency request to /dev/cpu_dma_latency to disable all CPUs specific idle
+states (if latency = 0uS then disable all idle states):
+# echo "what_ever_latency_you_need_in_uS" > /dev/cpu_dma_latency
+
+Disable specific CPU's specific idle state:
+# echo 1 > /sys/devices/system/cpu/cpu$cpu/cpuidle/state$state/disable
+
+
+Output format
+-------------
+
+Here is an example of the debugging output format:
+
+ARM external debug module:
+CPU[0]:
+ EDPRSR:  0000000b (Power:On DLK:Unlock)
+ EDPCSR:  [<ffff00000808eb54>] handle_IPI+0xe4/0x150
+ EDCIDSR: 00000000
+ EDVIDSR: 90000000 (State:Non-secure Mode:EL1/0 Width:64bits VMID:0)
+CPU[1]:
+ EDPRSR:  0000000b (Power:On DLK:Unlock)
+ EDPCSR:  [<ffff0000087a64c0>] debug_notifier_call+0x108/0x288
+ EDCIDSR: 00000000
+ EDVIDSR: 90000000 (State:Non-secure Mode:EL1/0 Width:64bits VMID:0)