| Message ID | 20240324-x1e80100-phy-edp-compatible-refactor-v5-0-a0db5f3150bc@linaro.org |
|---|---|
| Headers | show |
| Series | phy: qcom: edp: Allow eDP/DP configuring via set_mode op | expand |
On Sun, 24 Mar 2024 20:50:16 +0200, Abel Vesa wrote: > Until now, all platform that supported both eDP and DP had different > compatibles for each mode. Using different compatibles for basically > the same IP block but for a different configuration is bad way all > around. There is a new compute platform from Qualcomm that supports > both eDP and DP with the same PHY. So instead of following the old > method, we should allow the submode to be configured via set_mode from > the controller driver. > > [...] Applied, thanks! [1/2] phy: Add Embedded DisplayPort and DisplayPort submodes commit: 368d67dab4cc4a3ffd39fbd062b2f5796cdbb37b [2/2] phy: qcom: edp: Add set_mode op for configuring eDP/DP submode commit: 6078b8ce070cad3f9a8ecfce65d0f6d595494f02 Best regards,
Until now, all platform that supported both eDP and DP had different compatibles for each mode. Using different compatibles for basically the same IP block but for a different configuration is bad way all around. There is a new compute platform from Qualcomm that supports both eDP and DP with the same PHY. So instead of following the old method, we should allow the submode to be configured via set_mode from the controller driver. The controller part will follow after we conclude the PHY part first. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- Changes in v5: - Dropped the unnecessary ternary operator. - Link to v4: https://lore.kernel.org/r/20240216-x1e80100-phy-edp-compatible-refactor-v4-0-c07fd1a52186@linaro.org Changes in v4: - Added todo comment about setting the value of cfg8 based on swing pre-emph availability, like Konrad suggested - Fixed the condition in qcom_edp_phy_power_on, reported by Dmitry - Link to v3: https://lore.kernel.org/r/20240129-x1e80100-phy-edp-compatible-refactor-v3-0-e71f3359c535@linaro.org Changes in v3: - Dropped needs_swing_pre_emph_cfg as we store the table instead - Picking the table based on is_edp instead of overriding. - Link to v2: https://lore.kernel.org/r/20231222-x1e80100-phy-edp-compatible-refactor-v2-0-ab5786c2359f@linaro.org Changes in v2: - Dropped the dedicated xlate function and added set_mode op instead - Dropped the eDP PHY type and mode addition - Added the DP PHY submodes (eDP and DP) - Removed the device match data storing from the container struct - Link to v1: https://lore.kernel.org/r/20231219-x1e80100-phy-edp-compatible-refactor-v1-0-f9e77752953d@linaro.org Initial attepmpt was here: https://lore.kernel.org/all/20231122-phy-qualcomm-edp-x1e80100-v3-3-576fc4e9559d@linaro.org/ Compared to that version, this one uses the phy-cells method and drops the X1E80100 support. The X1E80100 support will be a separate patchset. --- Abel Vesa (2): phy: Add Embedded DisplayPort and DisplayPort submodes phy: qcom: edp: Add set_mode op for configuring eDP/DP submode drivers/phy/qualcomm/phy-qcom-edp.c | 76 +++++++++++++++++++++++++++---------- include/linux/phy/phy-dp.h | 3 ++ 2 files changed, 59 insertions(+), 20 deletions(-) --- base-commit: 2d5c7b7eb345249cb34d42cbc2b97b4c57ea944e change-id: 20231219-x1e80100-phy-edp-compatible-refactor-8733eca7ccda Best regards,