diff mbox series

[v2,3/3] arm64: dts: qcom: Add support for X1-based Asus Zenbook A14

Message ID 20250402084646.10098-4-alex.vinarskis@gmail.com
State Superseded
Headers show
Series [v2,1/3] dt-bindings: arm: qcom: Add Asus Zenbook A14 | expand

Commit Message

Aleksandrs Vinarskis April 2, 2025, 8:44 a.m. UTC 
Initial support for Asus Zenbook A14. Particular moddel exists
in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).

Mostly similar to other X1-based laptops. Notable differences are:
* Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
  and Qualcomm FastConnect 7800 on UX3407RA
* USB Type-C retimers are Parade PS8833, appear to behave identical
  to Parade PS8830
* gpio90 is TZ protected

Working:
* Keyboard
* Touchpad
* NVME
* Lid switch
* Camera LED
* eDP (FHD OLED, SDC420D) with brightness control
* Bluetooth, WiFi (WCN6855)
* USB Type-A port
* USB Type-C ports in USB2/USB3/DP (both orientations)
* aDSP/cDPS firmware loading, battery info
* Sleep/suspend, nothing visibly broken on resume

Out of scope of this series:
* Audio (Speakers/microphones/headphone jack)
* Camera (OmniVision OV02C10)
* HDMI (Parade PS185HDM)
* EC

Add dtsi and create two configurations for UX3407QA, UX3407RA.
Tested on UX3407QA with X1-26-100.

Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |    2 +
 arch/arm64/boot/dts/qcom/x1-zenbook-a14.dtsi  | 1258 +++++++++++++++++
 .../dts/qcom/x1e80100-asus-zenbook-a14.dts    |   45 +
 .../dts/qcom/x1p42100-asus-zenbook-a14.dts    |   48 +
 4 files changed, 1353 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1-zenbook-a14.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
 create mode 100644 arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts

Comments

Konrad Dybcio April 11, 2025, 11:36 p.m. UTC | #1 
On 4/2/25 10:44 AM, Aleksandrs Vinarskis wrote:
> Initial support for Asus Zenbook A14. Particular moddel exists
> in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).
> 
> Mostly similar to other X1-based laptops. Notable differences are:
> * Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
>   and Qualcomm FastConnect 7800 on UX3407RA
> * USB Type-C retimers are Parade PS8833, appear to behave identical
>   to Parade PS8830
> * gpio90 is TZ protected
> 
> Working:
> * Keyboard
> * Touchpad
> * NVME
> * Lid switch
> * Camera LED
> * eDP (FHD OLED, SDC420D) with brightness control
> * Bluetooth, WiFi (WCN6855)
> * USB Type-A port
> * USB Type-C ports in USB2/USB3/DP (both orientations)
> * aDSP/cDPS firmware loading, battery info
> * Sleep/suspend, nothing visibly broken on resume
> 
> Out of scope of this series:
> * Audio (Speakers/microphones/headphone jack)
> * Camera (OmniVision OV02C10)
> * HDMI (Parade PS185HDM)
> * EC
> 
> Add dtsi and create two configurations for UX3407QA, UX3407RA.
> Tested on UX3407QA with X1-26-100.
> 
> Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
> ---

[...]

> +	/* Left-side display-adjacent port, PS8833 */
> +	typec-mux@8 {
> +		compatible = "parade,ps8830";

What Krzysztof referred to with fallback compatible is this:

diff --git a/Documentation/devicetree/bindings/usb/parade,ps8830.yaml b/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
index 935d57f5d26f..aeb33667818e 100644
--- a/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
+++ b/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
@@ -11,8 +11,11 @@ maintainers:
 
 properties:
   compatible:
-    enum:
-      - parade,ps8830
+    oneOf:
+      - items:
+          - const: parade,ps8833
+          - const: parade,ps8830
+      - const: parade,ps8830


so that in case there are any sw changes down the line, people with older
DT receive the fixes, as if "parade,ps8833" is attributed to a driver, it
will match (due to being the primary entry) and if it's not (like today),
it will fall back to matching the next compatible (and the driver currently
looks for just that)

[...]

> +	eusb6_repeater: redriver@4f {
> +		compatible = "nxp,ptn3222";
> +		reg = <0x4f>;
> +		#phy-cells = <0>;
> +
> +		vdd3v3-supply = <&vreg_l13b_3p0>;
> +		vdd1v8-supply = <&vreg_l4b_1p8>;
> +
> +		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
> +
> +		pinctrl-0 = <&eusb6_reset_n>;
> +		pinctrl-names = "default";
> +	};
> +
> +	/* EC */

It's customary to leave the i2c address to make it slightly easier for
the next tinkerer ;)

[...]

> +&uart14 {
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "qcom,wcn7850-bt";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_en_default>;
> +		enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
> +		max-speed = <3000000>;

You'll need to provide some supplies, coming out of a pwrseq device, see
e.g. the QCP

Konrad
Aleksandrs Vinarskis April 12, 2025, 11:47 a.m. UTC | #2 
On Sat, 12 Apr 2025 at 01:36, Konrad Dybcio
<konrad.dybcio@oss.qualcomm.com> wrote:
>
> On 4/2/25 10:44 AM, Aleksandrs Vinarskis wrote:
> > Initial support for Asus Zenbook A14. Particular moddel exists
> > in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).
> >
> > Mostly similar to other X1-based laptops. Notable differences are:
> > * Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
> >   and Qualcomm FastConnect 7800 on UX3407RA
> > * USB Type-C retimers are Parade PS8833, appear to behave identical
> >   to Parade PS8830
> > * gpio90 is TZ protected
> >
> > Working:
> > * Keyboard
> > * Touchpad
> > * NVME
> > * Lid switch
> > * Camera LED
> > * eDP (FHD OLED, SDC420D) with brightness control
> > * Bluetooth, WiFi (WCN6855)
> > * USB Type-A port
> > * USB Type-C ports in USB2/USB3/DP (both orientations)
> > * aDSP/cDPS firmware loading, battery info
> > * Sleep/suspend, nothing visibly broken on resume
> >
> > Out of scope of this series:
> > * Audio (Speakers/microphones/headphone jack)
> > * Camera (OmniVision OV02C10)
> > * HDMI (Parade PS185HDM)
> > * EC
> >
> > Add dtsi and create two configurations for UX3407QA, UX3407RA.
> > Tested on UX3407QA with X1-26-100.
> >
> > Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
> > ---
>
> [...]
>
> > +     /* Left-side display-adjacent port, PS8833 */
> > +     typec-mux@8 {
> > +             compatible = "parade,ps8830";
>
> What Krzysztof referred to with fallback compatible is this:
>
> diff --git a/Documentation/devicetree/bindings/usb/parade,ps8830.yaml b/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
> index 935d57f5d26f..aeb33667818e 100644
> --- a/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
> +++ b/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
> @@ -11,8 +11,11 @@ maintainers:
>
>  properties:
>    compatible:
> -    enum:
> -      - parade,ps8830
> +    oneOf:
> +      - items:
> +          - const: parade,ps8833
> +          - const: parade,ps8830
> +      - const: parade,ps8830
>
>
> so that in case there are any sw changes down the line, people with older
> DT receive the fixes, as if "parade,ps8833" is attributed to a driver, it
> will match (due to being the primary entry) and if it's not (like today),
> it will fall back to matching the next compatible (and the driver currently
> looks for just that)
>

Hi,

Thanks, was not aware of that, found it in the examples now, will update.
As Krzysztof suggested to drop the patch adding compatible from
driver's code, If I understand correctly I also need the following dts
change, could you please confirm:

```
compatible = "parade,ps8833", "parade,ps8830";
```

> [...]
>
> > +     eusb6_repeater: redriver@4f {
> > +             compatible = "nxp,ptn3222";
> > +             reg = <0x4f>;
> > +             #phy-cells = <0>;
> > +
> > +             vdd3v3-supply = <&vreg_l13b_3p0>;
> > +             vdd1v8-supply = <&vreg_l4b_1p8>;
> > +
> > +             reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
> > +
> > +             pinctrl-0 = <&eusb6_reset_n>;
> > +             pinctrl-names = "default";
> > +     };
> > +
> > +     /* EC */
>
> It's customary to leave the i2c address to make it slightly easier for
> the next tinkerer ;)

I am unsure about the address. There are multiple addresses showing up
when discovering the bus, 0x1d, 0x5b, 0x61, 0x6a. Did a quick SMBUS
analysis, they all have non-zero registers responding... My best guess
right now is its 0x5b, as messing with it enabled backlight and broke
the keyboard. Will add that one.

>
> [...]
>
> > +&uart14 {
> > +     status = "okay";
> > +
> > +     bluetooth {
> > +             compatible = "qcom,wcn7850-bt";
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&bt_en_default>;
> > +             enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
> > +             max-speed = <3000000>;
>
> You'll need to provide some supplies, coming out of a pwrseq device, see
> e.g. the QCP
>

I assume you are referring to change like this [1]. There were some
discussions on whether the supplies are modelled correctly as it seems
to be different when using m.2 card, so as I was not sure about this
platform I did not add it. At least in the variant that I have, the
wcn6855 is soldered onboard, so I would assume so is the wcn7850
variant.
It seems that the two use quite different supplies - are the platform
dependent, or only wlan card dependent? Ie. Can I just copy pwrseq for
wcn6855 from a different platform?

For  wcn7850's pwrseq, I can add similarly to other platforms, but
cannot verify it. Should I still add it in this case?

A bit unrelated question: in the meantime I managed to bring-up the
sound on Zenbook as well. Would it be more correct to wait for this
series to land, and then send it separately, or is it okay to add it
in directly on re-spin?

Thank you,
Alex

https://lore.kernel.org/all/20250331204610.526672-2-alex.vinarskis@gmail.com/

> Konrad
Konrad Dybcio April 14, 2025, 9:49 a.m. UTC | #3 
On 4/12/25 1:47 PM, Aleksandrs Vinarskis wrote:
> On Sat, 12 Apr 2025 at 01:36, Konrad Dybcio
> <konrad.dybcio@oss.qualcomm.com> wrote:
>>
>> On 4/2/25 10:44 AM, Aleksandrs Vinarskis wrote:
>>> Initial support for Asus Zenbook A14. Particular moddel exists
>>> in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).
>>>
>>> Mostly similar to other X1-based laptops. Notable differences are:
>>> * Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
>>>   and Qualcomm FastConnect 7800 on UX3407RA
>>> * USB Type-C retimers are Parade PS8833, appear to behave identical
>>>   to Parade PS8830
>>> * gpio90 is TZ protected
>>>
>>> Working:
>>> * Keyboard
>>> * Touchpad
>>> * NVME
>>> * Lid switch
>>> * Camera LED
>>> * eDP (FHD OLED, SDC420D) with brightness control
>>> * Bluetooth, WiFi (WCN6855)
>>> * USB Type-A port
>>> * USB Type-C ports in USB2/USB3/DP (both orientations)
>>> * aDSP/cDPS firmware loading, battery info
>>> * Sleep/suspend, nothing visibly broken on resume
>>>
>>> Out of scope of this series:
>>> * Audio (Speakers/microphones/headphone jack)
>>> * Camera (OmniVision OV02C10)
>>> * HDMI (Parade PS185HDM)
>>> * EC
>>>
>>> Add dtsi and create two configurations for UX3407QA, UX3407RA.
>>> Tested on UX3407QA with X1-26-100.
>>>
>>> Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
>>> ---
>>
>> [...]
>>
>>> +     /* Left-side display-adjacent port, PS8833 */
>>> +     typec-mux@8 {
>>> +             compatible = "parade,ps8830";
>>
>> What Krzysztof referred to with fallback compatible is this:
>>
>> diff --git a/Documentation/devicetree/bindings/usb/parade,ps8830.yaml b/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
>> index 935d57f5d26f..aeb33667818e 100644
>> --- a/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
>> +++ b/Documentation/devicetree/bindings/usb/parade,ps8830.yaml
>> @@ -11,8 +11,11 @@ maintainers:
>>
>>  properties:
>>    compatible:
>> -    enum:
>> -      - parade,ps8830
>> +    oneOf:
>> +      - items:
>> +          - const: parade,ps8833
>> +          - const: parade,ps8830
>> +      - const: parade,ps8830
>>
>>
>> so that in case there are any sw changes down the line, people with older
>> DT receive the fixes, as if "parade,ps8833" is attributed to a driver, it
>> will match (due to being the primary entry) and if it's not (like today),
>> it will fall back to matching the next compatible (and the driver currently
>> looks for just that)
>>
> 
> Hi,
> 
> Thanks, was not aware of that, found it in the examples now, will update.
> As Krzysztof suggested to drop the patch adding compatible from
> driver's code, If I understand correctly I also need the following dts
> change, could you please confirm:
> 
> ```
> compatible = "parade,ps8833", "parade,ps8830";
> ```

Yep!

>>> +     eusb6_repeater: redriver@4f {
>>> +             compatible = "nxp,ptn3222";
>>> +             reg = <0x4f>;
>>> +             #phy-cells = <0>;
>>> +
>>> +             vdd3v3-supply = <&vreg_l13b_3p0>;
>>> +             vdd1v8-supply = <&vreg_l4b_1p8>;
>>> +
>>> +             reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
>>> +
>>> +             pinctrl-0 = <&eusb6_reset_n>;
>>> +             pinctrl-names = "default";
>>> +     };
>>> +
>>> +     /* EC */
>>
>> It's customary to leave the i2c address to make it slightly easier for
>> the next tinkerer ;)
> 
> I am unsure about the address. There are multiple addresses showing up
> when discovering the bus, 0x1d, 0x5b, 0x61, 0x6a. Did a quick SMBUS
> analysis, they all have non-zero registers responding... My best guess
> right now is its 0x5b, as messing with it enabled backlight and broke
> the keyboard. Will add that one.

It may be that there are also some 'dumb' devices, like program-and-forget
regulators or similar components, that aren't even described in your [SD]SDT

>>> +&uart14 {
>>> +     status = "okay";
>>> +
>>> +     bluetooth {
>>> +             compatible = "qcom,wcn7850-bt";
>>> +             pinctrl-names = "default";
>>> +             pinctrl-0 = <&bt_en_default>;
>>> +             enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
>>> +             max-speed = <3000000>;
>>
>> You'll need to provide some supplies, coming out of a pwrseq device, see
>> e.g. the QCP
>>
> 
> I assume you are referring to change like this [1]. There were some
> discussions on whether the supplies are modelled correctly as it seems
> to be different when using m.2 card, so as I was not sure about this
> platform I did not add it. At least in the variant that I have, the
> wcn6855 is soldered onboard, so I would assume so is the wcn7850
> variant.
> It seems that the two use quite different supplies - are the platform
> dependent, or only wlan card dependent? Ie. Can I just copy pwrseq for
> wcn6855 from a different platform?

The power sequencer is a description of the hardware that's part of the
same die as the wifi logic, IIUC

The inputs are most likely fixed per SoC+PMIC combo for various reasons

> For  wcn7850's pwrseq, I can add similarly to other platforms, but
> cannot verify it. Should I still add it in this case?

Let's not introduce it then

> A bit unrelated question: in the meantime I managed to bring-up the
> sound on Zenbook as well. Would it be more correct to wait for this
> series to land, and then send it separately, or is it okay to add it
> in directly on re-spin?

Let's get what we have merged first

Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index adb4d026bcc4..baa99f9e43ab 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -297,6 +297,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e78100-lenovo-thinkpad-t14s.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e78100-lenovo-thinkpad-t14s-oled.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-asus-vivobook-s15.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-asus-zenbook-a14.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-dell-xps13-9345.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-hp-omnibook-x14.dtb
@@ -304,4 +305,5 @@  dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-lenovo-yoga-slim7x.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-microsoft-romulus13.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-microsoft-romulus15.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-qcp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-asus-zenbook-a14.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1-zenbook-a14.dtsi b/arch/arm64/boot/dts/qcom/x1-zenbook-a14.dtsi
new file mode 100644
index 000000000000..fa556a52b857
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1-zenbook-a14.dtsi
@@ -0,0 +1,1258 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1e80100-pmics.dtsi"
+
+/ {
+	model = "ASUS Zenbook A14";
+	chassis-type = "laptop";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			label = "lid";
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&cam_indicator_en>;
+		pinctrl-names = "default";
+
+		led-camera-indicator {
+			label = "white:camera-indicator";
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			/* Reuse as a panic indicator until we get a "camera on" trigger */
+			panic-indicator;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Left-side display-adjacent port */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss0_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
+					};
+				};
+			};
+		};
+
+		/* Left-side user-adjacent port */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss1_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss1_con_sbu_out>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&misc_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vreg_vph_pwr>;
+		vdd-bob2-supply = <&vreg_vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vreg_vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vreg_vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vreg_vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vreg_vph_pwr>;
+		vdd-s2-supply = <&vreg_vph_pwr>;
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vreg_vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p9: ldo1 {
+			regulator-name = "vreg_l1j_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* ELAN, 04F3:3315 */
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* Left-side display-adjacent port, PS8833 */
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK3>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* ASUSTeK, 0B05:4543 */
+	hdtl@17 {
+		compatible = "hid-over-i2c";
+		reg = <0x17>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 95 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&hdtl_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	/* EC */
+};
+
+&i2c7 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* Left-side user-adjacent port, PS8833 */
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+		vdd-supply = <&vreg_rtmr1_1p15>;
+		vdd33-supply = <&vreg_rtmr1_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+		vddar-supply = <&vreg_rtmr1_1p15>;
+		vddat-supply = <&vreg_rtmr1_1p15>;
+		vddio-supply = <&vreg_rtmr1_1p8>;
+
+		reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr1_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss1_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss1_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss1_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* ASUSTeK, 0B05:0220 */
+	keyboard@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	compatible = "qcom,x1e80100-dp";
+	/delete-property/ #sound-dai-cells;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+			power-supply = <&vreg_edp_3p3>;
+
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp3_out: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>;
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+
+	usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>;
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-disable;
+		input-disable;
+		output-enable;
+		drive-push-pull;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&pm8550ve_9_gpios {
+	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>;
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_3_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <1>;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_5_gpios {
+	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>;
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&spi10 {
+	status = "disabled";
+
+	/* Unknown device */
+};
+
+&tlmm {
+	gpio-reserved-ranges = <44 4>,  /* SPI11, TZ Protected */
+			       <90 1>;	/* Unknown, TZ Protected */
+
+	bt_en_default: bt-en-sleep {
+		pins = "gpio116";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	cam_indicator_en: cam-indicator-en-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	hdtl_default: hdtl-default-state {
+		pins = "gpio95";
+		function = "gpio";
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	rtmr1_default: rtmr1-reset-n-active-state {
+		pins = "gpio176";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-disable;
+	};
+
+	usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state {
+		pins = "gpio188";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state {
+		pins = "gpio175";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state {
+		pins = "gpio186";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart21 {
+	compatible = "qcom,geni-debug-uart";
+
+	status = "okay";
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&retimer_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_1_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&retimer_ss1_ss_in>;
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p9>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p9>;
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts b/arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
new file mode 100644
index 000000000000..0b70ab396cf4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e80100-asus-zenbook-a14.dts
@@ -0,0 +1,45 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "x1e80100.dtsi"
+#include "x1-zenbook-a14.dtsi"
+
+/ {
+	model = "ASUS Zenbook A14 (UX3407RA)";
+	compatible = "asus,zenbook-a14-ux3407ra", "qcom,x1e80100";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qcdxkmsuc8380.mbn";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qcadsp8380.mbn",
+			"qcom/x1e80100/ASUSTeK/zenbook-a14/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qccdsp8380.mbn",
+			"qcom/x1e80100/ASUSTeK/zenbook-a14/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en_default>;
+		enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+		max-speed = <3000000>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts b/arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
new file mode 100644
index 000000000000..48d2eefeadc3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1p42100-asus-zenbook-a14.dts
@@ -0,0 +1,48 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "x1p42100.dtsi"
+#include "x1-zenbook-a14.dtsi"
+
+/delete-node/ &pmc8380_6;
+/delete-node/ &pmc8380_6_thermal;
+
+/ {
+	model = "ASUS Zenbook A14 (UX3407QA)";
+	compatible = "asus,zenbook-a14-ux3407qa", "qcom,x1p42100";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1e80100/ASUSTeK/zenbook-a14/qcdxkmsucpurwa.mbn";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1p42100/ASUSTeK/zenbook-a14/qcadsp8380.mbn",
+			"qcom/x1p42100/ASUSTeK/zenbook-a14/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1p42100/ASUSTeK/zenbook-a14/qccdsp8380.mbn",
+			"qcom/x1p42100/ASUSTeK/zenbook-a14/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn6855-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en_default>;
+		enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+		max-speed = <3000000>;
+	};
+};