| Message ID | 1481292919-26587-8-git-send-email-benjamin.gaignard@st.com |
|---|---|
| State | New |
| Headers | show |
On Fri, Dec 09, 2016 at 03:15:18PM +0100, Benjamin Gaignard wrote: > Add Timers and it sub-nodes into DT for stm32f429 family. > > version 6: > - split patch in two: one for SoC family and one for stm32f469 > discovery board. > > version 5: > - rename gptimer node to timers > - re-order timers node par addresses > > version 4: > - remove unwanted indexing in pwm@ and timer@ node name > - use "reg" instead of additional parameters to set timer > configuration > > version 3: > - use "st,stm32-timer-trigger" in DT > > version 2: > - use parameters to describe hardware capabilities > - do not use references for pwm and iio timer subnodes > > Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> > --- > arch/arm/boot/dts/stm32f429.dtsi | 275 +++++++++++++++++++++++++++++++++++++++ > 1 file changed, 275 insertions(+) > > diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi > index bca491d..d0fb9cc 100644 > --- a/arch/arm/boot/dts/stm32f429.dtsi > +++ b/arch/arm/boot/dts/stm32f429.dtsi > @@ -355,6 +355,21 @@ > slew-rate = <2>; > }; > }; > + > + pwm1_pins: pwm@1 { No reg prop, so should not have a unit-address. Given the names in the define below, seems like "timer1" would be appropriate. > + pins { > + pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>, > + <STM32F429_PB13_FUNC_TIM1_CH1N>, > + <STM32F429_PB12_FUNC_TIM1_BKIN>; > + }; > + }; > + > + pwm3_pins: pwm@3 { > + pins { > + pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>, > + <STM32F429_PB5_FUNC_TIM3_CH2>; > + }; > + }; > }; > > rcc: rcc@40023810 { > @@ -426,6 +441,266 @@ > interrupts = <80>; > clocks = <&rcc 0 38>; > }; > + > + timers2: timers@40000000 { timer@... It may be more than just a timer, there's not a better generic name. > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40000000 0x400>; > + clocks = <&rcc 0 128>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <1>; > + status = "disabled"; > + }; > + }; > + > + timers3: timers@40000400 { ditto > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40000400 0x400>; > + clocks = <&rcc 0 129>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <2>; > + status = "disabled"; > + }; > + }; > + > + timers4: timers@40000800 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40000800 0x400>; > + clocks = <&rcc 0 130>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <3>; > + status = "disabled"; > + }; > + }; > + > + timers5: timers@40000C00 { timer@... And use lowercase hex. > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40000C00 0x400>; ditto > + clocks = <&rcc 0 131>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <4>; > + status = "disabled"; > + }; > + }; > + > + timers6: timers@40001000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40001000 0x400>; > + clocks = <&rcc 0 132>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <5>; > + status = "disabled"; > + }; > + }; > + > + timers7: timers@40001400 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40001400 0x400>; > + clocks = <&rcc 0 133>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <6>; > + status = "disabled"; > + }; > + }; > + > + timers12: timers@40001800 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40001800 0x400>; > + clocks = <&rcc 0 134>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <9>; > + status = "disabled"; > + }; > + }; > + > + timers13: timers@40001C00 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40001C00 0x400>; > + clocks = <&rcc 0 135>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + }; > + > + timers14: timers@40002000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40002000 0x400>; > + clocks = <&rcc 0 136>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + }; > + > + timers1: timers@40010000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40010000 0x400>; > + clocks = <&rcc 0 160>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <0>; > + status = "disabled"; > + }; > + }; > + > + timers8: timers@40010400 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40010400 0x400>; > + clocks = <&rcc 0 161>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <7>; > + status = "disabled"; > + }; > + }; > + > + timers9: timers@40014000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40014000 0x400>; > + clocks = <&rcc 0 176>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + > + timer { > + compatible = "st,stm32-timer-trigger"; > + reg = <8>; > + status = "disabled"; > + }; > + }; > + > + timers10: timers@40014400 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40014400 0x400>; > + clocks = <&rcc 0 177>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + }; > + > + timers11: timers@40014800 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-timers"; > + reg = <0x40014800 0x400>; > + clocks = <&rcc 0 178>; > + clock-names = "clk_int"; > + status = "disabled"; > + > + pwm { > + compatible = "st,stm32-pwm"; > + status = "disabled"; > + }; > + }; > }; > }; > > -- > 1.9.1 >
2016-12-12 19:59 GMT+01:00 Rob Herring <robh@kernel.org>: > On Fri, Dec 09, 2016 at 03:15:18PM +0100, Benjamin Gaignard wrote: >> Add Timers and it sub-nodes into DT for stm32f429 family. >> >> version 6: >> - split patch in two: one for SoC family and one for stm32f469 >> discovery board. >> >> version 5: >> - rename gptimer node to timers >> - re-order timers node par addresses >> >> version 4: >> - remove unwanted indexing in pwm@ and timer@ node name >> - use "reg" instead of additional parameters to set timer >> configuration >> >> version 3: >> - use "st,stm32-timer-trigger" in DT >> >> version 2: >> - use parameters to describe hardware capabilities >> - do not use references for pwm and iio timer subnodes >> >> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> >> --- >> arch/arm/boot/dts/stm32f429.dtsi | 275 +++++++++++++++++++++++++++++++++++++++ >> 1 file changed, 275 insertions(+) >> >> diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi >> index bca491d..d0fb9cc 100644 >> --- a/arch/arm/boot/dts/stm32f429.dtsi >> +++ b/arch/arm/boot/dts/stm32f429.dtsi >> @@ -355,6 +355,21 @@ >> slew-rate = <2>; >> }; >> }; >> + >> + pwm1_pins: pwm@1 { > > No reg prop, so should not have a unit-address. Given the names in the > define below, seems like "timer1" would be appropriate. > >> + pins { >> + pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>, >> + <STM32F429_PB13_FUNC_TIM1_CH1N>, >> + <STM32F429_PB12_FUNC_TIM1_BKIN>; >> + }; >> + }; >> + >> + pwm3_pins: pwm@3 { >> + pins { >> + pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>, >> + <STM32F429_PB5_FUNC_TIM3_CH2>; >> + }; >> + }; >> }; >> >> rcc: rcc@40023810 { >> @@ -426,6 +441,266 @@ >> interrupts = <80>; >> clocks = <&rcc 0 38>; >> }; >> + >> + timers2: timers@40000000 { > > timer@... > > It may be more than just a timer, there's not a better generic name. > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000000 0x400>; >> + clocks = <&rcc 0 128>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <1>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers3: timers@40000400 { > > ditto > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000400 0x400>; >> + clocks = <&rcc 0 129>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <2>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers4: timers@40000800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000800 0x400>; >> + clocks = <&rcc 0 130>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <3>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers5: timers@40000C00 { > > timer@... > > And use lowercase hex. > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000C00 0x400>; > > ditto > >> + clocks = <&rcc 0 131>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <4>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers6: timers@40001000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001000 0x400>; >> + clocks = <&rcc 0 132>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <5>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers7: timers@40001400 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001400 0x400>; >> + clocks = <&rcc 0 133>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <6>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers12: timers@40001800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001800 0x400>; >> + clocks = <&rcc 0 134>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <9>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers13: timers@40001C00 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001C00 0x400>; >> + clocks = <&rcc 0 135>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers14: timers@40002000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40002000 0x400>; >> + clocks = <&rcc 0 136>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers1: timers@40010000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40010000 0x400>; >> + clocks = <&rcc 0 160>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <0>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers8: timers@40010400 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40010400 0x400>; >> + clocks = <&rcc 0 161>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <7>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers9: timers@40014000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40014000 0x400>; >> + clocks = <&rcc 0 176>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <8>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers10: timers@40014400 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40014400 0x400>; >> + clocks = <&rcc 0 177>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers11: timers@40014800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40014800 0x400>; >> + clocks = <&rcc 0 178>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> }; >> }; >> >> -- >> 1.9.1 >> -- Benjamin Gaignard Graphic Study Group Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog
diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi index bca491d..d0fb9cc 100644 --- a/arch/arm/boot/dts/stm32f429.dtsi +++ b/arch/arm/boot/dts/stm32f429.dtsi @@ -355,6 +355,21 @@ slew-rate = <2>; }; }; + + pwm1_pins: pwm@1 { + pins { + pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>, + <STM32F429_PB13_FUNC_TIM1_CH1N>, + <STM32F429_PB12_FUNC_TIM1_BKIN>; + }; + }; + + pwm3_pins: pwm@3 { + pins { + pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>, + <STM32F429_PB5_FUNC_TIM3_CH2>; + }; + }; }; rcc: rcc@40023810 { @@ -426,6 +441,266 @@ interrupts = <80>; clocks = <&rcc 0 38>; }; + + timers2: timers@40000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000000 0x400>; + clocks = <&rcc 0 128>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <1>; + status = "disabled"; + }; + }; + + timers3: timers@40000400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000400 0x400>; + clocks = <&rcc 0 129>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <2>; + status = "disabled"; + }; + }; + + timers4: timers@40000800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000800 0x400>; + clocks = <&rcc 0 130>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <3>; + status = "disabled"; + }; + }; + + timers5: timers@40000C00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000C00 0x400>; + clocks = <&rcc 0 131>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <4>; + status = "disabled"; + }; + }; + + timers6: timers@40001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001000 0x400>; + clocks = <&rcc 0 132>; + clock-names = "clk_int"; + status = "disabled"; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <5>; + status = "disabled"; + }; + }; + + timers7: timers@40001400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001400 0x400>; + clocks = <&rcc 0 133>; + clock-names = "clk_int"; + status = "disabled"; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <6>; + status = "disabled"; + }; + }; + + timers12: timers@40001800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001800 0x400>; + clocks = <&rcc 0 134>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <9>; + status = "disabled"; + }; + }; + + timers13: timers@40001C00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001C00 0x400>; + clocks = <&rcc 0 135>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + timers14: timers@40002000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40002000 0x400>; + clocks = <&rcc 0 136>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + timers1: timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 160>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <0>; + status = "disabled"; + }; + }; + + timers8: timers@40010400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010400 0x400>; + clocks = <&rcc 0 161>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <7>; + status = "disabled"; + }; + }; + + timers9: timers@40014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014000 0x400>; + clocks = <&rcc 0 176>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-timer-trigger"; + reg = <8>; + status = "disabled"; + }; + }; + + timers10: timers@40014400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014400 0x400>; + clocks = <&rcc 0 177>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + timers11: timers@40014800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014800 0x400>; + clocks = <&rcc 0 178>; + clock-names = "clk_int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; }; };
Add Timers and it sub-nodes into DT for stm32f429 family. version 6: - split patch in two: one for SoC family and one for stm32f469 discovery board. version 5: - rename gptimer node to timers - re-order timers node par addresses version 4: - remove unwanted indexing in pwm@ and timer@ node name - use "reg" instead of additional parameters to set timer configuration version 3: - use "st,stm32-timer-trigger" in DT version 2: - use parameters to describe hardware capabilities - do not use references for pwm and iio timer subnodes Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> --- arch/arm/boot/dts/stm32f429.dtsi | 275 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 275 insertions(+) -- 1.9.1