@@ -5,6 +5,7 @@
*/
#include <net/mac80211.h>
+#include <net/cfg80211.h>
#include <linux/etherdevice.h>
#include "mac.h"
@@ -8670,11 +8671,13 @@ ath12k_mac_vdev_start_restart(struct ath12k_link_vif *arvif,
struct ath12k_base *ab = ar->ab;
struct wmi_vdev_start_req_arg arg = {};
const struct cfg80211_chan_def *chandef = &ctx->def;
+ struct ieee80211_hw *hw = ath12k_ar_to_hw(ar);
struct ath12k_vif *ahvif = arvif->ahvif;
struct ieee80211_bss_conf *link_conf;
+ unsigned int dfs_cac_time;
int ret;
- lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
+ lockdep_assert_wiphy(hw->wiphy);
link_conf = ath12k_mac_get_link_bss_conf(arvif);
if (!link_conf) {
@@ -8772,20 +8775,20 @@ ath12k_mac_vdev_start_restart(struct ath12k_link_vif *arvif,
ath12k_dbg(ab, ATH12K_DBG_MAC, "vdev %pM started, vdev_id %d\n",
ahvif->vif->addr, arvif->vdev_id);
- /* Enable CAC Flag in the driver by checking the channel DFS cac time,
- * i.e dfs_cac_ms value which will be valid only for radar channels
- * and state as NL80211_DFS_USABLE which indicates CAC needs to be
- * done before channel usage. This flags is used to drop rx packets.
+ /* Enable CAC Running Flag in the driver by checking all sub-channel's DFS
+ * state as NL80211_DFS_USABLE which indicates CAC needs to be
+ * done before channel usage. This flag is used to drop rx packets.
* during CAC.
*/
/* TODO: Set the flag for other interface types as required */
- if (arvif->ahvif->vdev_type == WMI_VDEV_TYPE_AP &&
- chandef->chan->dfs_cac_ms &&
- chandef->chan->dfs_state == NL80211_DFS_USABLE) {
+ if (arvif->ahvif->vdev_type == WMI_VDEV_TYPE_AP && ctx->radar_enabled &&
+ cfg80211_chandef_dfs_usable(hw->wiphy, chandef)) {
set_bit(ATH12K_FLAG_CAC_RUNNING, &ar->dev_flags);
+ dfs_cac_time = cfg80211_chandef_dfs_cac_time(hw->wiphy, chandef);
+
ath12k_dbg(ab, ATH12K_DBG_MAC,
- "CAC Started in chan_freq %d for vdev %d\n",
- arg.freq, arg.vdev_id);
+ "CAC started dfs_cac_time %u center_freq %d center_freq1 %d for vdev %d\n",
+ dfs_cac_time, arg.freq, arg.band_center_freq1, arg.vdev_id);
}
ret = ath12k_mac_set_txbf_conf(arvif);
Currently, the DFS CAC time and the usable state of the primary channel in the channel definition are used to set the CAC_RUNNING flag for the ath12k radio structure. However, this approach is flawed because there are channel definitions where the primary channel is not a DFS channel, but the secondary channel is. For example, in 5 GHz band, channel 36 with 160 MHz bandwidth. In such cases, the flag is not set correctly and hence places where this flag is tested will not operate as expected. For example, Rx packets will not be dropped. To fix this issue, use the cfg80211_chandef_dfs_usable() function from cfg80211, which returns true if at least one channel is in a usable state. This will ensure the CAC_RUNNING flag is set properly. Additionally, update the CAC running debug log message to include the CAC time in milliseconds and also print the center frequency segment 1. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> --- drivers/net/wireless/ath/ath12k/mac.c | 23 +++++++++++++---------- 1 file changed, 13 insertions(+), 10 deletions(-)