@@ -152,6 +152,7 @@
#define BQ24296_REG_VPRS_PN_MASK (BIT(7) | BIT(6) | BIT(5))
#define BQ24296_REG_VPRS_PN_SHIFT 5
#define BQ24296_REG_VPRS_PN_24296 0x1
+#define BQ24296_REG_VPRS_PN_24297 0x3
#define BQ24190_REG_VPRS_TS_PROFILE_MASK BIT(2)
#define BQ24190_REG_VPRS_TS_PROFILE_SHIFT 2
#define BQ24190_REG_VPRS_DEV_REG_MASK (BIT(1) | BIT(0))
@@ -208,6 +209,7 @@ enum bq24190_chip {
BQ24192i,
BQ24196,
BQ24296,
+ BQ24297,
};
/*
@@ -1904,6 +1906,7 @@ static int bq24296_check_chip(struct bq24190_dev_info *bdi)
switch (v) {
case BQ24296_REG_VPRS_PN_24296:
+ case BQ24296_REG_VPRS_PN_24297:
break;
default:
dev_err(bdi->dev, "Error unknown model: 0x%02x\n", v);
@@ -2033,6 +2036,17 @@ static const struct bq24190_chip_info bq24190_chip_info_tbl[] = {
.ichg_array_size = BQ24296_CCC_ICHG_VALUES_LEN,
#ifdef CONFIG_REGULATOR
.vbus_desc = &bq24296_vbus_desc,
+#endif
+ .check_chip = bq24296_check_chip,
+ .set_chg_config = bq24296_battery_set_chg_config,
+ .ntc_fault_mask = BQ24296_REG_F_NTC_FAULT_MASK,
+ .get_ntc_status = bq24296_charger_get_ntc_status,
+ .set_otg_vbus = bq24296_set_otg_vbus,
+ },
+ [BQ24297] = {
+ .ichg_array_size = BQ24296_CCC_ICHG_VALUES_LEN,
+#ifdef CONFIG_REGULATOR
+ .vbus_desc = &bq24296_vbus_desc,
#endif
.check_chip = bq24296_check_chip,
.set_chg_config = bq24296_battery_set_chg_config,
@@ -2296,6 +2310,7 @@ static const struct i2c_device_id bq24190_i2c_ids[] = {
{ "bq24192i", (kernel_ulong_t)&bq24190_chip_info_tbl[BQ24192i] },
{ "bq24196", (kernel_ulong_t)&bq24190_chip_info_tbl[BQ24196] },
{ "bq24296", (kernel_ulong_t)&bq24190_chip_info_tbl[BQ24296] },
+ { "bq24297", (kernel_ulong_t)&bq24190_chip_info_tbl[BQ24297] },
{ },
};
MODULE_DEVICE_TABLE(i2c, bq24190_i2c_ids);
@@ -2306,6 +2321,7 @@ static const struct of_device_id bq24190_of_match[] = {
{ .compatible = "ti,bq24192i", .data = &bq24190_chip_info_tbl[BQ24192i] },
{ .compatible = "ti,bq24196", .data = &bq24190_chip_info_tbl[BQ24196] },
{ .compatible = "ti,bq24296", .data = &bq24190_chip_info_tbl[BQ24296] },
+ { .compatible = "ti,bq24297", .data = &bq24190_chip_info_tbl[BQ24297] },
{ },
};
MODULE_DEVICE_TABLE(of, bq24190_of_match);
The BQ24297 is identical to the BQ24296 except that it uses USB D+ / D- data-lines for charger-type (max. input-current) detection instead of a PSEL input pin. This is the same difference as between the already supported BQ24190 (D+ / D-) and the BQ24192 (PSEL). Note just like with the BQ24190 vs BQ24192 there is no difference how the charger-IC works at the register-level. The only difference is in the external hardware interface. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- drivers/power/supply/bq24190_charger.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)