| Message ID | 20241118-x1e80100-crd-fp-v1-1-ec6b553a2e53@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: qcom: x1e80100-crd: Add USB multiport fingerprint reader | expand |
On 18.11.2024 11:34 AM, Stephan Gerhold wrote: > The X1E80100 CRD has a Goodix fingerprint reader connected to the USB > multiport controller on eUSB6. All other ports (including USB super-speed > pins) are unused. > > Set it up in the device tree together with the NXP PTN3222 repeater. > > Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Konrad
[ +CC: Krishna, Thinh and the USB list ] On Mon, Nov 18, 2024 at 11:34:29AM +0100, Stephan Gerhold wrote: > The X1E80100 CRD has a Goodix fingerprint reader connected to the USB > multiport controller on eUSB6. All other ports (including USB super-speed > pins) are unused. > > Set it up in the device tree together with the NXP PTN3222 repeater. > > Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> > --- > arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 48 +++++++++++++++++++++++++++++++ > 1 file changed, 48 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > index 39f9d9cdc10d..44942931c18f 100644 > --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > @@ -735,6 +735,26 @@ keyboard@3a { > }; > }; > > +&i2c5 { > + clock-frequency = <400000>; > + > + status = "okay"; > + > + eusb6_repeater: redriver@4f { > + compatible = "nxp,ptn3222"; > + reg = <0x4f>; The driver does not currently check that there's actually anything at this address. Did you verify that this is the correct address? (Abel is adding a check to the driver as we speak to catch any such mistakes going forward). > + #phy-cells = <0>; nit: I'd put provider properties like this one last. > + vdd3v3-supply = <&vreg_l13b_3p0>; > + vdd1v8-supply = <&vreg_l4b_1p8>; Sort by supply name? > + reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; > + > + pinctrl-0 = <&eusb6_reset_n>; > + pinctrl-names = "default"; > + }; > +}; > + > &i2c8 { > clock-frequency = <400000>; > > @@ -1047,6 +1067,14 @@ edp_reg_en: edp-reg-en-state { > bias-disable; > }; > > + eusb6_reset_n: eusb6-reset-n-state { > + pins = "gpio184"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + output-low; I don't think the pin config should assert reset, that should be up to the driver to control. > + }; > + > hall_int_n_default: hall-int-n-state { > pins = "gpio92"; > function = "gpio"; > @@ -1260,3 +1288,23 @@ &usb_1_ss2_dwc3_hs { > &usb_1_ss2_qmpphy_out { > remote-endpoint = <&pmic_glink_ss2_ss_in>; > }; > + > +&usb_mp { > + status = "okay"; > +}; > + > +&usb_mp_dwc3 { > + /* Limit to USB 2.0 and single port */ > + maximum-speed = "high-speed"; > + phys = <&usb_mp_hsphy1>; > + phy-names = "usb2-1"; > +}; The dwc3 driver determines (and acts on) the number of ports based on the port interrupts in DT and controller capabilities. I'm not sure we can (should) just drop the other HS PHY and the SS PHYs that would still be there in the SoC (possibly initialised by the boot firmware). I had a local patch to enable the multiport controller (for the suspend work) and I realise that you'd currently need to specify a repeater also for the HS PHY which does not have one, but that should be possible to fix somehow. > + > +&usb_mp_hsphy1 { > + vdd-supply = <&vreg_l2e_0p8>; > + vdda12-supply = <&vreg_l3e_1p2>; > + > + phys = <&eusb6_repeater>; > + > + status = "okay"; > +}; Johan
On Tue, Dec 03, 2024 at 11:20:48AM +0100, Johan Hovold wrote: > [ +CC: Krishna, Thinh and the USB list ] > > On Mon, Nov 18, 2024 at 11:34:29AM +0100, Stephan Gerhold wrote: > > The X1E80100 CRD has a Goodix fingerprint reader connected to the USB > > multiport controller on eUSB6. All other ports (including USB super-speed > > pins) are unused. > > > > Set it up in the device tree together with the NXP PTN3222 repeater. > > > > Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> > > --- > > arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 48 +++++++++++++++++++++++++++++++ > > 1 file changed, 48 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > > index 39f9d9cdc10d..44942931c18f 100644 > > --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > > +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > > @@ -735,6 +735,26 @@ keyboard@3a { > > }; > > }; > > > > +&i2c5 { > > + clock-frequency = <400000>; > > + > > + status = "okay"; > > + > > + eusb6_repeater: redriver@4f { > > + compatible = "nxp,ptn3222"; > > + reg = <0x4f>; > > The driver does not currently check that there's actually anything at > this address. Did you verify that this is the correct address? > > (Abel is adding a check to the driver as we speak to catch any such > mistakes going forward). > Yes, I verified this using https://git.codelinaro.org/stephan.gerhold/linux/-/commit/45d5add498612387f88270ca944ee16e2236fddd (I sent this to Abel back then, so I'm surprised he didn't run that :-)) > > + #phy-cells = <0>; > > nit: I'd put provider properties like this one last. > > > + vdd3v3-supply = <&vreg_l13b_3p0>; > > + vdd1v8-supply = <&vreg_l4b_1p8>; > > Sort by supply name? > Ack. > > + reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; > > + > > + pinctrl-0 = <&eusb6_reset_n>; > > + pinctrl-names = "default"; > > + }; > > +}; > > + > > &i2c8 { > > clock-frequency = <400000>; > > > > @@ -1047,6 +1067,14 @@ edp_reg_en: edp-reg-en-state { > > bias-disable; > > }; > > > > + eusb6_reset_n: eusb6-reset-n-state { > > + pins = "gpio184"; > > + function = "gpio"; > > + drive-strength = <2>; > > + bias-disable; > > + output-low; > > I don't think the pin config should assert reset, that should be up to > the driver to control. > I can drop it I guess, but pinctrl is applied before the driver takes control of the GPIO. This means if the GPIO happens to be in input mode before the driver loads (with pull up or pull down), then we would briefly leave it floating when applying the bias-disable. Or I guess we could drop the bias-disable, since it shouldn't be relevant for a pin we keep in output mode all the time? > > + }; > > + > > hall_int_n_default: hall-int-n-state { > > pins = "gpio92"; > > function = "gpio"; > > @@ -1260,3 +1288,23 @@ &usb_1_ss2_dwc3_hs { > > &usb_1_ss2_qmpphy_out { > > remote-endpoint = <&pmic_glink_ss2_ss_in>; > > }; > > + > > +&usb_mp { > > + status = "okay"; > > +}; > > + > > +&usb_mp_dwc3 { > > + /* Limit to USB 2.0 and single port */ > > + maximum-speed = "high-speed"; > > + phys = <&usb_mp_hsphy1>; > > + phy-names = "usb2-1"; > > +}; > > The dwc3 driver determines (and acts on) the number of ports based on > the port interrupts in DT and controller capabilities. > > I'm not sure we can (should) just drop the other HS PHY and the SS PHYs > that would still be there in the SoC (possibly initialised by the boot > firmware). > > I had a local patch to enable the multiport controller (for the suspend > work) and I realise that you'd currently need to specify a repeater also > for the HS PHY which does not have one, but that should be possible to > fix somehow. > I think there are two separate questions here: 1. Should we (or do we even need to) enable unused PHYs? 2. Do we need to power off unused PHYs left enabled by the firmware? For (1), I'm not not sure if there is a technical reason that requires us to. And given that PHYs typically consume quite a bit of power, I'm not sure if we should. Perhaps it's not worth spending effort on this minor optimization now, but then the device tree would ideally still tell us which PHYs are actually used (for future optimizations). For (2), yes, we probably need to. But my impression so far is that this might be a larger problem that we need to handle on the SoC level. I have seen some firmware versions that blindly power up all USB controllers, even completely unused ones. Ideally we would power down unused components during startup and then leave them off. Thanks, Stephan
+Cc Dmitry On Tue, Dec 03, 2024 at 02:03:05PM +0200, Abel Vesa wrote: > On 24-12-03 12:30:37, Stephan Gerhold wrote: > > On Tue, Dec 03, 2024 at 11:20:48AM +0100, Johan Hovold wrote: > > > [ +CC: Krishna, Thinh and the USB list ] > > > > > > On Mon, Nov 18, 2024 at 11:34:29AM +0100, Stephan Gerhold wrote: > > > > The X1E80100 CRD has a Goodix fingerprint reader connected to the USB > > > > multiport controller on eUSB6. All other ports (including USB super-speed > > > > pins) are unused. > > > > > > > > Set it up in the device tree together with the NXP PTN3222 repeater. > > > > > > > > Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> > > > > --- > > > > arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 48 +++++++++++++++++++++++++++++++ > > > > 1 file changed, 48 insertions(+) > > > > > > > > diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > > > > index 39f9d9cdc10d..44942931c18f 100644 > > > > --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > > > > +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts > > > > @@ -735,6 +735,26 @@ keyboard@3a { > > > > }; > > > > }; > > > > > > > > +&i2c5 { > > > > + clock-frequency = <400000>; > > > > + > > > > + status = "okay"; > > > > + > > > > + eusb6_repeater: redriver@4f { > > > > + compatible = "nxp,ptn3222"; > > > > + reg = <0x4f>; > > > > > > The driver does not currently check that there's actually anything at > > > this address. Did you verify that this is the correct address? > > > > > > (Abel is adding a check to the driver as we speak to catch any such > > > mistakes going forward). > > > > > > > Yes, I verified this using > > https://git.codelinaro.org/stephan.gerhold/linux/-/commit/45d5add498612387f88270ca944ee16e2236fddd > > > > (I sent this to Abel back then, so I'm surprised he didn't run that :-)) > > I don't remember seeing this commit back then. Maybe I didn't look > careful enough. Sorry. > > Since you already did the work, can you send that on the list? > Sure, no problem. What exactly do we want for upstream? My patch above isn't ideal, because it checks the CHIP_ID on every PHY power up. But briefly powering up the PHY during probe() just for reading the CHIP_ID is also a bit weird. Not sure what the best approach here is. Thanks, Stephan
On 12/3/2024 6:45 PM, Krishna Kurapati wrote: > > > On 12/3/2024 3:50 PM, Johan Hovold wrote: >> [ +CC: Krishna, Thinh and the USB list ] >> >> On Mon, Nov 18, 2024 at 11:34:29AM +0100, Stephan Gerhold wrote: >>> The X1E80100 CRD has a Goodix fingerprint reader connected to the USB >>> multiport controller on eUSB6. All other ports (including USB >>> super-speed >>> pins) are unused. >>> >>> Set it up in the device tree together with the NXP PTN3222 repeater. >>> >>> Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> >>> --- >>> arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 48 >>> +++++++++++++++++++++++++++++++ >>> 1 file changed, 48 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>> b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>> index 39f9d9cdc10d..44942931c18f 100644 >>> --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>> +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>> @@ -735,6 +735,26 @@ keyboard@3a { >>> }; >>> }; >>> +&i2c5 { >>> + clock-frequency = <400000>; >>> + >>> + status = "okay"; >>> + >>> + eusb6_repeater: redriver@4f { >>> + compatible = "nxp,ptn3222"; >>> + reg = <0x4f>; >> >> The driver does not currently check that there's actually anything at >> this address. Did you verify that this is the correct address? >> >> (Abel is adding a check to the driver as we speak to catch any such >> mistakes going forward). >> >>> + #phy-cells = <0>; >> >> nit: I'd put provider properties like this one last. >> >>> + vdd3v3-supply = <&vreg_l13b_3p0>; >>> + vdd1v8-supply = <&vreg_l4b_1p8>; >> >> Sort by supply name? >> >>> + reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; >>> + >>> + pinctrl-0 = <&eusb6_reset_n>; >>> + pinctrl-names = "default"; >>> + }; >>> +}; >>> + >>> &i2c8 { >>> clock-frequency = <400000>; >>> @@ -1047,6 +1067,14 @@ edp_reg_en: edp-reg-en-state { >>> bias-disable; >>> }; >>> + eusb6_reset_n: eusb6-reset-n-state { >>> + pins = "gpio184"; >>> + function = "gpio"; >>> + drive-strength = <2>; >>> + bias-disable; >>> + output-low; >> >> I don't think the pin config should assert reset, that should be up to >> the driver to control. >> >>> + }; >>> + >>> hall_int_n_default: hall-int-n-state { >>> pins = "gpio92"; >>> function = "gpio"; >>> @@ -1260,3 +1288,23 @@ &usb_1_ss2_dwc3_hs { >>> &usb_1_ss2_qmpphy_out { >>> remote-endpoint = <&pmic_glink_ss2_ss_in>; >>> }; >>> + >>> +&usb_mp { >>> + status = "okay"; >>> +}; >>> + >>> +&usb_mp_dwc3 { >>> + /* Limit to USB 2.0 and single port */ >>> + maximum-speed = "high-speed"; >>> + phys = <&usb_mp_hsphy1>; >>> + phy-names = "usb2-1"; >>> +}; >> >> The dwc3 driver determines (and acts on) the number of ports based on >> the port interrupts in DT and controller capabilities. >> >> I'm not sure we can (should) just drop the other HS PHY and the SS PHYs >> that would still be there in the SoC (possibly initialised by the boot >> firmware). >> > > The DWC3 core driver identifies number of ports based on xHCI registers. > The QC Wrapper reads this number via interrupts. But these two values > are independent of each other. The core driver uses these values to > identify and manipulate phys. Even if only one HS is given in multiport > it would be sufficient if the name is "usb2-1". If the others are > missing, those phys would be read by driver as NULL and any ops to phys > would be NOP. > However do we need to reduce the number of interrupts used in DTS ? We don't need to give all interrupts as there is only one port present. We don't want to enable all interrupts when ports are not exposed. Regards, Krishna,
On 12/5/2024 1:46 PM, Johan Hovold wrote: > On Thu, Dec 05, 2024 at 01:32:29PM +0530, Krishna Kurapati wrote: >> On 12/3/2024 6:45 PM, Krishna Kurapati wrote: >>> On 12/3/2024 3:50 PM, Johan Hovold wrote: >>>> On Mon, Nov 18, 2024 at 11:34:29AM +0100, Stephan Gerhold wrote: > >>>>> +&usb_mp_dwc3 { >>>>> + /* Limit to USB 2.0 and single port */ >>>>> + maximum-speed = "high-speed"; >>>>> + phys = <&usb_mp_hsphy1>; >>>>> + phy-names = "usb2-1"; >>>>> +}; >>>> >>>> The dwc3 driver determines (and acts on) the number of ports based on >>>> the port interrupts in DT and controller capabilities. >>>> >>>> I'm not sure we can (should) just drop the other HS PHY and the SS PHYs >>>> that would still be there in the SoC (possibly initialised by the boot >>>> firmware). >>> >>> The DWC3 core driver identifies number of ports based on xHCI registers. >>> The QC Wrapper reads this number via interrupts. But these two values >>> are independent of each other. The core driver uses these values to >>> identify and manipulate phys. Even if only one HS is given in multiport >>> it would be sufficient if the name is "usb2-1". If the others are >>> missing, those phys would be read by driver as NULL and any ops to phys >>> would be NOP. > > No, the core driver still acts on these ports (to some extent) even if > there is no PHY specified (e.g. updates DWC3_GUSB2PHYCFG on suspend). > Yes, since the port count is obtained from xHCI registers, the GUSB2PHYCFG/ GUSB3PIPECTL regs are modified regardless we use the PHYs or not but this is still fine. It can be considered a NOP AFAIK. > And IIRC I even had to specify more than just the fingerprint reader PHY > on the X13s to get it to enumerate. I never had time to fully determine > why this was the case though. > This might need to be checked. Did you attempt adding each phy individually ? Just incase the first PHY is not the one corresponding to the fingerprint reader. Regards, Krishna, >> However do we need to reduce the number of interrupts used in DTS ? >> We don't need to give all interrupts as there is only one port present. >> We don't want to enable all interrupts when ports are not exposed. > > No, the interrupts are still there, wired up in the SoC, so we should > not change that. > > With runtime PM eventually enabled and working as it should, the OS > should be able to power down any unused ports. And we could also > consider marking some ports as not physically accessible and not > connected as a further hint to the OS that they can be disabled even > sooner. > > Johan
On Thu, Dec 05, 2024 at 01:52:08PM +0530, Krishna Kurapati wrote: > On 12/5/2024 1:46 PM, Johan Hovold wrote: > > And IIRC I even had to specify more than just the fingerprint reader PHY > > on the X13s to get it to enumerate. I never had time to fully determine > > why this was the case though. > > This might need to be checked. Did you attempt adding each phy > individually ? Just incase the first PHY is not the one corresponding to > the fingerprint reader. Yes, I tried each PHY in turn, and only enabling the HS and SS PHY for the fingerprint reader port, but that was not enough. Johan
On 3.12.2024 5:05 PM, Stephan Gerhold wrote: > On Tue, Dec 03, 2024 at 09:07:22PM +0530, Krishna Kurapati wrote: >> On 12/3/2024 5:00 PM, Stephan Gerhold wrote: >>> On Tue, Dec 03, 2024 at 11:20:48AM +0100, Johan Hovold wrote: >>>> [ +CC: Krishna, Thinh and the USB list ] >>>> >>>> On Mon, Nov 18, 2024 at 11:34:29AM +0100, Stephan Gerhold wrote: >>>>> The X1E80100 CRD has a Goodix fingerprint reader connected to the USB >>>>> multiport controller on eUSB6. All other ports (including USB super-speed >>>>> pins) are unused. >>>>> >>>>> Set it up in the device tree together with the NXP PTN3222 repeater. >>>>> >>>>> Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> >>>>> --- >>>>> arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 48 +++++++++++++++++++++++++++++++ >>>>> 1 file changed, 48 insertions(+) >>>>> >>>>> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>>>> index 39f9d9cdc10d..44942931c18f 100644 >>>>> --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>>>> +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts >>>>> @@ -735,6 +735,26 @@ keyboard@3a { >>>>> [...] >>>>> @@ -1260,3 +1288,23 @@ &usb_1_ss2_dwc3_hs { >>>>> &usb_1_ss2_qmpphy_out { >>>>> remote-endpoint = <&pmic_glink_ss2_ss_in>; >>>>> }; >>>>> + >>>>> +&usb_mp { >>>>> + status = "okay"; >>>>> +}; >>>>> + >>>>> +&usb_mp_dwc3 { >>>>> + /* Limit to USB 2.0 and single port */ >>>>> + maximum-speed = "high-speed"; >>>>> + phys = <&usb_mp_hsphy1>; >>>>> + phy-names = "usb2-1"; >>>>> +}; >>>> >>>> The dwc3 driver determines (and acts on) the number of ports based on >>>> the port interrupts in DT and controller capabilities. >>>> >>>> I'm not sure we can (should) just drop the other HS PHY and the SS PHYs >>>> that would still be there in the SoC (possibly initialised by the boot >>>> firmware). >>>> >>>> I had a local patch to enable the multiport controller (for the suspend >>>> work) and I realise that you'd currently need to specify a repeater also >>>> for the HS PHY which does not have one, but that should be possible to >>>> fix somehow. >>>> >>> >>> I think there are two separate questions here: >>> >>> 1. Should we (or do we even need to) enable unused PHYs? >>> 2. Do we need to power off unused PHYs left enabled by the firmware? >>> >>> For (1), I'm not not sure if there is a technical reason that requires >>> us to. And given that PHYs typically consume quite a bit of power, I'm >>> not sure if we should. Perhaps it's not worth spending effort on this >>> minor optimization now, but then the device tree would ideally still >>> tell us which PHYs are actually used (for future optimizations). >>> >>> For (2), yes, we probably need to. But my impression so far is that this >>> might be a larger problem that we need to handle on the SoC level. I >>> have seen some firmware versions that blindly power up all USB >>> controllers, even completely unused ones. Ideally we would power down >>> unused components during startup and then leave them off. >>> >> >> This question might be a dumb one, if so please ignore it. >> >> But if we skip adding unused phys in DTS node, the core driver wouldn't have >> access to all phys and we wouldn't be able to get references to unused ones >> (un-mentioned ones in DTS). So how can we power them off from core driver if >> we don't have reference to them ? >> > > The question is not dumb at all, it's a very valid one. :-) > > Perhaps it's easier if we keep them all listed on the USB controllers > and have something else to mark them as unused. The downside of that > option is that we might not be able to have a complete description of > the PHY with all resources. For example on the CRD there is no eUSB > repeater we could model for the first USB port (usb2-0), but it's needed > to enable the qcom,x1e80100-snps-eusb2-phy. So we have the choice between a silent failure or a loud non-failure wrt acquiring the repeater.. not sure which one is better Konrad
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts index 39f9d9cdc10d..44942931c18f 100644 --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts @@ -735,6 +735,26 @@ keyboard@3a { }; }; +&i2c5 { + clock-frequency = <400000>; + + status = "okay"; + + eusb6_repeater: redriver@4f { + compatible = "nxp,ptn3222"; + reg = <0x4f>; + #phy-cells = <0>; + + vdd3v3-supply = <&vreg_l13b_3p0>; + vdd1v8-supply = <&vreg_l4b_1p8>; + + reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&eusb6_reset_n>; + pinctrl-names = "default"; + }; +}; + &i2c8 { clock-frequency = <400000>; @@ -1047,6 +1067,14 @@ edp_reg_en: edp-reg-en-state { bias-disable; }; + eusb6_reset_n: eusb6-reset-n-state { + pins = "gpio184"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + hall_int_n_default: hall-int-n-state { pins = "gpio92"; function = "gpio"; @@ -1260,3 +1288,23 @@ &usb_1_ss2_dwc3_hs { &usb_1_ss2_qmpphy_out { remote-endpoint = <&pmic_glink_ss2_ss_in>; }; + +&usb_mp { + status = "okay"; +}; + +&usb_mp_dwc3 { + /* Limit to USB 2.0 and single port */ + maximum-speed = "high-speed"; + phys = <&usb_mp_hsphy1>; + phy-names = "usb2-1"; +}; + +&usb_mp_hsphy1 { + vdd-supply = <&vreg_l2e_0p8>; + vdda12-supply = <&vreg_l3e_1p2>; + + phys = <&eusb6_repeater>; + + status = "okay"; +};
The X1E80100 CRD has a Goodix fingerprint reader connected to the USB multiport controller on eUSB6. All other ports (including USB super-speed pins) are unused. Set it up in the device tree together with the NXP PTN3222 repeater. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> --- arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 48 +++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+)