@@ -3,7 +3,7 @@
* IPQ9574 RDP board common device tree source
*
* Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
- * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2023-2024, Qualcomm Innovation Center, Inc. All rights reserved.
*/
/dts-v1/;
@@ -164,6 +164,20 @@ &usb3 {
status = "okay";
};
+/*
+ * The bootstrap pins for the board select the XO clock frequency,
+ * which automatically enables the right dividers to ensure the
+ * reference clock output from WiFi is 48 MHZ.
+ */
+&ref_48mhz_clk {
+ clock-div = <1>;
+ clock-mult = <1>;
+};
+
&xo_board_clk {
clock-frequency = <24000000>;
};
+
+&xo_clk {
+ clock-frequency = <48000000>;
+};
@@ -3,10 +3,11 @@
* IPQ9574 SoC device tree source
*
* Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
- * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2023-2024, Qualcomm Innovation Center, Inc. All rights reserved.
*/
#include <dt-bindings/clock/qcom,apss-ipq.h>
+#include <dt-bindings/clock/qcom,ipq-cmn-pll.h>
#include <dt-bindings/clock/qcom,ipq9574-gcc.h>
#include <dt-bindings/interconnect/qcom,ipq9574.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -19,6 +20,12 @@ / {
#size-cells = <2>;
clocks {
+ ref_48mhz_clk: ref-48mhz-clk {
+ compatible = "fixed-factor-clock";
+ clocks = <&xo_clk>;
+ #clock-cells = <0>;
+ };
+
sleep_clk: sleep-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -28,6 +35,11 @@ xo_board_clk: xo-board-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
};
+
+ xo_clk: xo-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
};
cpus {
@@ -243,6 +255,18 @@ mdio: mdio@90000 {
status = "disabled";
};
+ cmn_pll: clock-controller@9b000 {
+ compatible = "qcom,ipq9574-cmn-pll";
+ reg = <0x0009b000 0x800>;
+ clocks = <&ref_48mhz_clk>,
+ <&gcc GCC_CMN_12GPLL_AHB_CLK>,
+ <&gcc GCC_CMN_12GPLL_SYS_CLK>;
+ clock-names = "ref", "ahb", "sys";
+ #clock-cells = <1>;
+ assigned-clocks = <&cmn_pll CMN_PLL_CLK>;
+ assigned-clock-rates-u64 = /bits/ 64 <12000000000>;
+ };
+
qfprom: efuse@a4000 {
compatible = "qcom,ipq9574-qfprom", "qcom,qfprom";
reg = <0x000a4000 0x5a1>;
The CMN PLL clock controller allows selection of an input clock rate from a defined set of input clock rates. It in-turn supplies fixed rate output clocks to the hardware blocks that provide the ethernet functions such as PPE (Packet Process Engine) and connected switch or PHY, and to GCC. The reference clock of CMN PLL is routed from XO to the CMN PLL through the internal WiFi block. .XO (48 MHZ or 96 MHZ)-->WiFi (multiplier/divider)-->48 MHZ to CMN PLL. The reference input clock from WiFi to CMN PLL is fully controlled by the bootstrap pins which select the XO frequency (48 MHZ or 96 MHZ). Based on this frequency, the divider in the internal Wi-Fi block is automatically configured by hardware (1 for 48 MHZ, 2 for 96 MHZ), to ensure output clock to CMN PLL is 48 MHZ. Signed-off-by: Luo Jie <quic_luoj@quicinc.com> --- arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi | 16 ++++++++++++++- arch/arm64/boot/dts/qcom/ipq9574.dtsi | 26 +++++++++++++++++++++++- 2 files changed, 40 insertions(+), 2 deletions(-)