@@ -241,6 +241,49 @@ void omap3_ctrl_write_boot_mode(u8 bootmode)
#endif
+/**
+ * omap_ctrl_write_dsp_boot_addr - set boot address for a remote processor
+ * @bootaddr: physical address of the boot loader
+ *
+ * Set boot address for the boot loader of a supported processor
+ * when a power ON sequence occurs.
+ */
+void omap_ctrl_write_dsp_boot_addr(u32 bootaddr)
+{
+ u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTADDR :
+ cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTADDR :
+ cpu_is_omap44xx() ? OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR :
+ 0;
+
+ if (!offset) {
+ pr_err("%s: unsupported omap type\n", __func__);
+ return;
+ }
+
+ omap_ctrl_writel(bootaddr, offset);
+}
+
+/**
+ * omap_ctrl_write_dsp_boot_mode - set boot mode for a remote processor
+ * @bootmode: 8-bit value to pass to some boot code
+ *
+ * Sets boot mode for the boot loader of a supported processor
+ * when a power ON sequence occurs.
+ */
+void omap_ctrl_write_dsp_boot_mode(u8 bootmode)
+{
+ u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTMOD :
+ cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTMOD :
+ 0;
+
+ if (!offset) {
+ pr_err("%s: unsupported omap type\n", __func__);
+ return;
+ }
+
+ omap_ctrl_writel(bootmode, offset);
+}
+
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
/*
* Clears the scratchpad contents in case of cold boot-
@@ -397,6 +397,8 @@ extern u32 omap3_arm_context[128];
extern void omap3_control_save_context(void);
extern void omap3_control_restore_context(void);
extern void omap3_ctrl_write_boot_mode(u8 bootmode);
+extern void omap_ctrl_write_dsp_boot_addr(u32 bootaddr);
+extern void omap_ctrl_write_dsp_boot_mode(u8 bootmode);
extern void omap3630_ctrl_disable_rta(void);
extern int omap3_ctrl_save_padconf(void);
#else
@@ -42,6 +42,7 @@
#define OMAP4_CTRL_MODULE_CORE_STD_FUSE_OPP_DPLL_1 0x0268
#define OMAP4_CTRL_MODULE_CORE_STATUS 0x02c4
#define OMAP4_CTRL_MODULE_CORE_DEV_CONF 0x0300
+#define OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR 0x0304
#define OMAP4_CTRL_MODULE_CORE_LDOVBB_IVA_VOLTAGE_CTRL 0x0314
#define OMAP4_CTRL_MODULE_CORE_LDOVBB_MPU_VOLTAGE_CTRL 0x0318
#define OMAP4_CTRL_MODULE_CORE_LDOSRAM_IVA_VOLTAGE_CTRL 0x0320
SCM contains boot addr and boot mode registers to control other processors on different OMAP versions. It controls the boot address and mode for DSP based subsystems like: IVA 2.1 (OMAP2430), IVA 2.2 (OMAP3) and DSP (OMAP4). If contained within SCM registers, when a processor is booting it uses BOOTADDR to start running the code at that location. BOOTMOD register specifies a different set of modes for the processor to execute when booting (from direct, idle, self-loop, user and default). Since there was no offset associated with OMAP4, this patch defines it. Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org> --- arch/arm/mach-omap2/control.c | 43 ++++++++++++++++++++ arch/arm/mach-omap2/control.h | 2 + .../include/mach/ctrl_module_core_44xx.h | 1 + 3 files changed, 46 insertions(+), 0 deletions(-)