diff mbox series

Documentation: msm-hsusb.txt: remove

Message ID 20240816090105.13651-2-omasanori@proton.me
State New
Headers show
Series Documentation: msm-hsusb.txt: remove | expand

Commit Message

Masanori Ogino Aug. 16, 2024, 9:02 a.m. UTC
From: Masanori Ogino <mogino@acm.org>

Commit a170a1e9ccc5 ("usb: phy: remove phy-msm-usb.c") removed the
device driver but left the corresponding documentation, delete it.

Signed-off-by: Masanori Ogino <mogino@acm.org>
---
 .../devicetree/bindings/usb/msm-hsusb.txt     | 110 ------------------
 1 file changed, 110 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/usb/msm-hsusb.txt
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
deleted file mode 100644
index afc30e98b123..000000000000
--- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt
+++ /dev/null
@@ -1,110 +0,0 @@ 
-MSM SoC HSUSB controllers
-
-EHCI
-
-Required properties:
-- compatible:	Should contain "qcom,ehci-host"
-- regs:			offset and length of the register set in the memory map
-- usb-phy:		phandle for the PHY device
-
-Example EHCI controller device node:
-
-	ehci: ehci@f9a55000 {
-		compatible = "qcom,ehci-host";
-		reg = <0xf9a55000 0x400>;
-		usb-phy = <&usb_otg>;
-	};
-
-USB PHY with optional OTG:
-
-Required properties:
-- compatible:   Should contain:
-  "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY
-  "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY
-
-- regs:         Offset and length of the register set in the memory map
-- interrupts:   interrupt-specifier for the OTG interrupt.
-
-- clocks:       A list of phandle + clock-specifier pairs for the
-                clocks listed in clock-names
-- clock-names:  Should contain the following:
-  "phy"         USB PHY reference clock
-  "core"        Protocol engine clock
-  "iface"       Interface bus clock
-  "alt_core"    Protocol engine clock for targets with asynchronous
-                reset methodology. (optional)
-
-- vdccx-supply: phandle to the regulator for the vdd supply for
-                digital circuit operation.
-- v1p8-supply:  phandle to the regulator for the 1.8V supply
-- v3p3-supply:  phandle to the regulator for the 3.3V supply
-
-- resets:       A list of phandle + reset-specifier pairs for the
-                resets listed in reset-names
-- reset-names:  Should contain the following:
-  "phy"         USB PHY controller reset
-  "link"        USB LINK controller reset
-
-- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of
-                1 - PHY control
-                2 - PMIC control
-
-Optional properties:
-- dr_mode:      One of "host", "peripheral" or "otg". Defaults to "otg"
-
-- switch-gpio:  A phandle + gpio-specifier pair. Some boards are using Dual
-                SPDT USB Switch, witch is controlled by GPIO to de/multiplex
-                D+/D- USB lines between connectors.
-
-- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device
-                Mode Eye Diagram test. Start address at which these values will be
-                written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as
-                "do not overwrite default value at this address".
-                For example: qcom,phy-init-sequence = < -1 0x63 >;
-                Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1.
-
-- qcom,phy-num: Select number of pyco-phy to use, can be one of
-                0 - PHY one, default
-                1 - Second PHY
-                Some platforms may have configuration to allow USB
-                controller work with any of the two HSPHYs present.
-
-- qcom,vdd-levels: This property must be a list of three integer values
-                (no, min, max) where each value represents either a voltage
-                in microvolts or a value corresponding to voltage corner.
-
-- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
-                and controller driver therefore enables pull-up explicitly
-                before starting controller using usbcmd run/stop bit.
-
-- extcon:       phandles to external connector devices. First phandle
-                should point to external connector, which provide "USB"
-                cable events, the second should point to external connector
-                device, which provide "USB-HOST" cable events. If one of
-                the external connector devices is not required empty <0>
-                phandle should be specified.
-
-Example HSUSB OTG controller device node:
-
-    usb@f9a55000 {
-        compatible = "qcom,usb-otg-snps";
-        reg = <0xf9a55000 0x400>;
-        interrupts = <0 134 0>;
-        dr_mode = "peripheral";
-
-        clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>,
-                <&gcc GCC_USB_HS_AHB_CLK>;
-
-        clock-names = "phy", "core", "iface";
-
-        vddcx-supply = <&pm8841_s2_corner>;
-        v1p8-supply = <&pm8941_l6>;
-        v3p3-supply = <&pm8941_l24>;
-
-        resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>;
-        reset-names = "phy", "link";
-
-        qcom,otg-control = <1>;
-        qcom,phy-init-sequence = < -1 0x63 >;
-        qcom,vdd-levels = <1 5 7>;
-	};