diff mbox series

[RFT] wifi: brcmfmac: Add optional lpo clock enable support

Message ID 20240802083400.166753-1-arend.vanspriel@broadcom.com
State New
Headers show
Series [RFT] wifi: brcmfmac: Add optional lpo clock enable support | expand

Commit Message

Arend van Spriel Aug. 2, 2024, 8:34 a.m. UTC
From: Jacobe Zang <jacobe.zang@wesion.com>

WiFi modules often require 32kHz clock to function. Add support to
enable the clock to PCIe driver and move "brcm,bcm4329-fmac" check
to the top of brcmf_of_probe

Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Jacobe Zang <jacobe.zang@wesion.com>
[arend: handle -EPROBE_DEFER scenario]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
---
Hi Jacobe,

Here the patch I tinkered up last night. Please verify. You can
probably test the error handling by adding:

clk = PTR_ERR(-EPROBE_DEFER);

Regards,
Arend 
---
 .../broadcom/brcm80211/brcmfmac/bcmsdh.c      |  4 +++
 .../broadcom/brcm80211/brcmfmac/common.c      |  6 ++++-
 .../wireless/broadcom/brcm80211/brcmfmac/of.c | 27 +++++++++++++------
 .../wireless/broadcom/brcm80211/brcmfmac/of.h |  9 ++++---
 .../broadcom/brcm80211/brcmfmac/pcie.c        |  3 +++
 .../broadcom/brcm80211/brcmfmac/sdio.c        | 18 ++++++++-----
 .../broadcom/brcm80211/brcmfmac/usb.c         |  3 +++
 7 files changed, 51 insertions(+), 19 deletions(-)


base-commit: 8400291e289ee6b2bf9779ff1c83a291501f017b

Comments

Arend van Spriel Aug. 3, 2024, 1:47 p.m. UTC | #1
On August 2, 2024 7:28:51 PM Florian Fainelli 
<florian.fainelli@broadcom.com> wrote:

> On 8/2/24 01:34, Arend van Spriel wrote:
>> From: Jacobe Zang <jacobe.zang@wesion.com>
>>
>> WiFi modules often require 32kHz clock to function. Add support to
>> enable the clock to PCIe driver and move "brcm,bcm4329-fmac" check
>> to the top of brcmf_of_probe
>>
>> Co-developed-by: Ondrej Jirman <megi@xff.cz>
>> Signed-off-by: Ondrej Jirman <megi@xff.cz>
>> Signed-off-by: Jacobe Zang <jacobe.zang@wesion.com>
>> [arend: handle -EPROBE_DEFER scenario]
>> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
>
> This looks fine for a cold boot case, how about handling suspend/resume
> where the clock might have been disabled, do we need to deal with an
> "always-on" Device Tree property as well as whether the device is
> enabled for wake-up or not?

Thanks, Florian

When the external LPO is disabled the chip will fallback on the internal (I 
think). So it is not an issue for wakeup scenario, but if the clock is not 
enabled upon resume we should deal with it. Could go in separate patch.

I can inquire about my assumption above.

Regards,
Arend
diff mbox series

Patch

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
index d35262335eaf..af31cfac0757 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
@@ -951,6 +951,10 @@  int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev)
 		ret = -ENODEV;
 		goto out;
 	}
+	if (IS_ERR(sdiodev->bus)) {
+		ret = PTR_ERR(sdiodev->bus);
+		goto out;
+	}
 	brcmf_sdiod_host_fixup(sdiodev->func2->card->host);
 out:
 	if (ret)
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
index b24faae35873..6c5d26f9b766 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
@@ -561,8 +561,12 @@  struct brcmf_mp_device *brcmf_get_module_param(struct device *dev,
 	if (!found) {
 		/* No platform data for this device, try OF and DMI data */
 		brcmf_dmi_probe(settings, chip, chiprev);
-		brcmf_of_probe(dev, bus_type, settings);
 		brcmf_acpi_probe(dev, bus_type, settings);
+		i = brcmf_of_probe(dev, bus_type, settings);
+		if (i < 0) {
+			kfree(settings);
+			settings = ERR_PTR(i);
+		}
 	}
 	return settings;
 }
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c
index fe4f65756105..a04dfdce4960 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c
@@ -6,6 +6,7 @@ 
 #include <linux/of.h>
 #include <linux/of_irq.h>
 #include <linux/of_net.h>
+#include <linux/clk.h>
 
 #include <defs.h>
 #include "debug.h"
@@ -65,18 +66,22 @@  static int brcmf_of_get_country_codes(struct device *dev,
 	return 0;
 }
 
-void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
-		    struct brcmf_mp_device *settings)
+int brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
+		   struct brcmf_mp_device *settings)
 {
 	struct brcmfmac_sdio_pd *sdio = &settings->bus.sdio;
 	struct device_node *root, *np = dev->of_node;
 	struct of_phandle_args oirq;
+	struct clk *clk;
 	const char *prop;
 	int irq;
 	int err;
 	u32 irqf;
 	u32 val;
 
+	if (!np || !of_device_is_compatible(np, "brcm,bcm4329-fmac"))
+		return 0;
+
 	/* Apple ARM64 platforms have their own idea of board type, passed in
 	 * via the device tree. They also have an antenna SKU parameter
 	 */
@@ -106,7 +111,7 @@  void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
 		board_type = devm_kstrdup(dev, tmp, GFP_KERNEL);
 		if (!board_type) {
 			of_node_put(root);
-			return;
+			return 0;
 		}
 		strreplace(board_type, '/', '-');
 		settings->board_type = board_type;
@@ -114,8 +119,13 @@  void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
 		of_node_put(root);
 	}
 
-	if (!np || !of_device_is_compatible(np, "brcm,bcm4329-fmac"))
-		return;
+	clk = devm_clk_get_optional_enabled(dev, "lpo");
+	if (!IS_ERR_OR_NULL(clk)) {
+		brcmf_dbg(INFO, "enabling 32kHz clock\n");
+		clk_set_rate(clk, 32768);
+	} else if (PTR_ERR_OR_ZERO(clk) == -EPROBE_DEFER) {
+		return -EPROBE_DEFER;
+	}
 
 	err = brcmf_of_get_country_codes(dev, settings);
 	if (err)
@@ -124,23 +134,24 @@  void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
 	of_get_mac_address(np, settings->mac);
 
 	if (bus_type != BRCMF_BUSTYPE_SDIO)
-		return;
+		return 0;
 
 	if (of_property_read_u32(np, "brcm,drive-strength", &val) == 0)
 		sdio->drive_strength = val;
 
 	/* make sure there are interrupts defined in the node */
 	if (of_irq_parse_one(np, 0, &oirq))
-		return;
+		return 0;
 
 	irq = irq_create_of_mapping(&oirq);
 	if (!irq) {
 		brcmf_err("interrupt could not be mapped\n");
-		return;
+		return 0;
 	}
 	irqf = irqd_get_trigger_type(irq_get_irq_data(irq));
 
 	sdio->oob_irq_supported = true;
 	sdio->oob_irq_nr = irq;
 	sdio->oob_irq_flags = irqf;
+	return 0;
 }
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h
index 10bf52253337..ae124c73fc3b 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h
@@ -3,11 +3,12 @@ 
  * Copyright (c) 2014 Broadcom Corporation
  */
 #ifdef CONFIG_OF
-void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
-		    struct brcmf_mp_device *settings);
+int brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
+		   struct brcmf_mp_device *settings);
 #else
-static void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
-			   struct brcmf_mp_device *settings)
+static int brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type,
+			  struct brcmf_mp_device *settings)
 {
+	return 0;
 }
 #endif /* CONFIG_OF */
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
index ce482a3877e9..190e8990618c 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
@@ -2452,6 +2452,9 @@  brcmf_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		ret = -ENOMEM;
 		goto fail;
 	}
+	ret = PTR_ERR_OR_ZERO(devinfo->settings);
+	if (ret < 0)
+		goto fail;
 
 	bus = kzalloc(sizeof(*bus), GFP_KERNEL);
 	if (!bus) {
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index 1461dc453ac2..2dbc08c36a09 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -3943,7 +3943,7 @@  static const struct brcmf_buscore_ops brcmf_sdio_buscore_ops = {
 	.write32 = brcmf_sdio_buscore_write32,
 };
 
-static bool
+static int
 brcmf_sdio_probe_attach(struct brcmf_sdio *bus)
 {
 	struct brcmf_sdio_dev *sdiodev;
@@ -3953,6 +3953,7 @@  brcmf_sdio_probe_attach(struct brcmf_sdio *bus)
 	u32 reg_val;
 	u32 drivestrength;
 	u32 enum_base;
+	int ret = -EBADE;
 
 	sdiodev = bus->sdiodev;
 	sdio_claim_host(sdiodev->func1);
@@ -4001,8 +4002,9 @@  brcmf_sdio_probe_attach(struct brcmf_sdio *bus)
 						   BRCMF_BUSTYPE_SDIO,
 						   bus->ci->chip,
 						   bus->ci->chiprev);
-	if (!sdiodev->settings) {
+	if (IS_ERR_OR_NULL(sdiodev->settings)) {
 		brcmf_err("Failed to get device parameters\n");
+		ret = PTR_ERR_OR_ZERO(sdiodev->settings);
 		goto fail;
 	}
 	/* platform specific configuration:
@@ -4071,7 +4073,7 @@  brcmf_sdio_probe_attach(struct brcmf_sdio *bus)
 	/* allocate header buffer */
 	bus->hdrbuf = kzalloc(MAX_HDR_READ + bus->head_align, GFP_KERNEL);
 	if (!bus->hdrbuf)
-		return false;
+		return -ENOMEM;
 	/* Locate an appropriately-aligned portion of hdrbuf */
 	bus->rxhdr = (u8 *) roundup((unsigned long)&bus->hdrbuf[0],
 				    bus->head_align);
@@ -4082,11 +4084,11 @@  brcmf_sdio_probe_attach(struct brcmf_sdio *bus)
 	if (bus->poll)
 		bus->pollrate = 1;
 
-	return true;
+	return 0;
 
 fail:
 	sdio_release_host(sdiodev->func1);
-	return false;
+	return ret;
 }
 
 static int
@@ -4446,6 +4448,7 @@  struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev)
 	struct brcmf_sdio *bus;
 	struct workqueue_struct *wq;
 	struct brcmf_fw_request *fwreq;
+	int probe_attach_result;
 
 	brcmf_dbg(TRACE, "Enter\n");
 
@@ -4474,7 +4477,8 @@  struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev)
 	bus->brcmf_wq = wq;
 
 	/* attempt to attach to the dongle */
-	if (!(brcmf_sdio_probe_attach(bus))) {
+	probe_attach_result = brcmf_sdio_probe_attach(bus);
+	if (probe_attach_result < 0) {
 		brcmf_err("brcmf_sdio_probe_attach failed\n");
 		goto fail;
 	}
@@ -4546,6 +4550,8 @@  struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev)
 
 fail:
 	brcmf_sdio_remove(bus);
+	if (probe_attach_result < 0)
+		return ERR_PTR(probe_attach_result);
 	return NULL;
 }
 
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c
index 8afbf529c745..2821c27f317e 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c
@@ -1272,6 +1272,9 @@  static int brcmf_usb_probe_cb(struct brcmf_usbdev_info *devinfo,
 		ret = -ENOMEM;
 		goto fail;
 	}
+	ret = PTR_ERR_OR_ZERO(devinfo->settings);
+	if (ret < 0)
+		goto fail;
 
 	if (!brcmf_usb_dlneeded(devinfo)) {
 		ret = brcmf_alloc(devinfo->dev, devinfo->settings);