@@ -14,6 +14,7 @@
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/export.h>
+#include <linux/gpio/consumer.h>
#include <linux/gpio/driver.h>
#include <linux/idr.h>
#include <linux/kthread.h>
@@ -1467,6 +1468,30 @@ static const struct serial_rs485 sc16is7xx_rs485_supported = {
.delay_rts_after_send = 1, /* Not supported but keep returning -EINVAL */
};
+/* Reset device, purging any pending irq / data */
+static int sc16is7xx_reset(struct device *dev, struct regmap *regmap)
+{
+ struct gpio_desc *reset_gpio;
+
+ /* The reset GPIO is ACTIVE_LOW, flag GPIOD_OUT_HIGH asserts the reset GPIO */
+ reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(reset_gpio))
+ return dev_err_probe(dev, PTR_ERR(reset_gpio), "Failed to get reset GPIO\n");
+
+ if (reset_gpio) {
+ /* The minimum reset pulse width is 3 us. */
+ udelay(5);
+ gpiod_set_value_cansleep(reset_gpio, 0);
+ /* Deassert GPIO */
+ } else {
+ /* Software reset */
+ regmap_write(regmap, SC16IS7XX_IOCONTROL_REG,
+ SC16IS7XX_IOCONTROL_SRESET_BIT);
+ }
+
+ return 0;
+}
+
int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
struct regmap *regmaps[], int irq)
{
@@ -1527,6 +1552,10 @@ int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
s->devtype = devtype;
dev_set_drvdata(dev, s);
+ ret = sc16is7xx_reset(dev, regmaps[0]);
+ if (ret)
+ goto out_clk;
+
kthread_init_worker(&s->kworker);
s->kworker_task = kthread_run(kthread_worker_fn, &s->kworker,
"sc16is7xx");
@@ -1536,10 +1565,6 @@ int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
}
sched_set_fifo(s->kworker_task);
- /* reset device, purging any pending irq / data */
- regmap_write(regmaps[0], SC16IS7XX_IOCONTROL_REG,
- SC16IS7XX_IOCONTROL_SRESET_BIT);
-
/* Mark each port line and status as uninitialised. */
for (i = 0; i < devtype->nr_uart; ++i) {
s->p[i].port.line = SC16IS7XX_MAX_DEVS;
Some boards connect a GPIO to the reset pin, and the reset pin needs to be setup correctly before accessing the chip. Add a function to handle the chip reset. If the reset-gpios is defined in the DT, do hardware reset through this GPIO, othwerwise do software reset as before. Signed-off-by: Hui Wang <hui.wang@canonical.com> --- In the v3: - drop Reviewed-by - adjust the sequence of if, else if and else - replace PTR_ERR(reset_gpiod) with dev_err_probe - change GPIOD_OUT_LOW to GPIOD_OUT_HIGH, this will assert the reset pin after requesting the GPIO - change the 2nd parameter struct regmap *regmap[] to struct regmap *regmap - address all spelling and description issues in the v2 drivers/tty/serial/sc16is7xx.c | 33 +++++++++++++++++++++++++++++---- 1 file changed, 29 insertions(+), 4 deletions(-)