@@ -3338,10 +3338,6 @@ FIT uImage format:
CONFIG_SPL_INIT_MINIMAL
Arch init code should be built for a very small image
- CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
- Size of partition on the MMC to load U-Boot from
- when the MMC is being used in raw mode.
-
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
Partition on the MMC to load U-Boot from when the MMC is being
used in raw mode
@@ -275,7 +275,6 @@
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -335,7 +335,6 @@
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -193,7 +193,6 @@
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -237,7 +237,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -236,7 +236,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -52,8 +52,6 @@
#define CONFIG_GENERIC_MMC
#define CONFIG_OMAP_HSMMC
#define CONFIG_SUPPORT_EMMC_BOOT
-/* RAW SD card / eMMC locations. */
- #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#endif /* CONFIG_EMMC_BOOT */
/*
@@ -47,8 +47,6 @@
#define CONFIG_GENERIC_MMC
#define CONFIG_OMAP_HSMMC
#define CONFIG_SUPPORT_EMMC_BOOT
-/* RAW SD card / eMMC locations. */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
/* Always 64 KiB env size */
#define CONFIG_ENV_SIZE (64 << 10)
@@ -131,7 +131,6 @@
/* SPL related MMC defines */
#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS ((512 << 10) / 512) /* 512KiB */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
#endif
@@ -240,7 +240,6 @@
/* misc */
#define CONFIG_STACKSIZE (128 * 1024)
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
#define CONFIG_MISC_INIT_R
/* SPL */
@@ -292,7 +292,6 @@
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -30,11 +30,6 @@
#define CONFIG_SYS_NS16550_COM4 UART4_BASE
#define CONFIG_BAUDRATE 115200
-/* SD/MMC RAW boot */
-#undef CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
-
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 /* 384 KB */
-
/* MMC ENV related defines */
#undef CONFIG_ENV_OFFSET
#undef CONFIG_ENV_SIZE
@@ -133,7 +133,6 @@
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS ((512 << 10) / 512) /* 512KiB */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
#endif
@@ -45,8 +45,6 @@
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
-
#undef CONFIG_MII
#undef CONFIG_PHY_GIGE
#define CONFIG_PHY_SMSC
@@ -103,8 +103,6 @@
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
-
#undef CONFIG_MII
#undef CONFIG_PHY_GIGE
#define CONFIG_PHY_SMSC
@@ -37,9 +37,8 @@
/* MMC support */
#if defined(CONFIG_SPL_MMC_SUPPORT)
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
-#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS/2*1024)
+#define CONFIG_SYS_MONITOR_LEN 409600 /* 400 KB */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#endif
@@ -61,7 +61,6 @@ unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x600
#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1a000
@@ -108,15 +108,11 @@
#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
/*
* HDR would be appended at end of image and copied to DDR along
* with U-Boot image.
*/
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS (0x400 + \
- (CONFIG_U_BOOT_HDR_SIZE / 512)
-#else
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
#endif /* ifdef CONFIG_SECURE_BOOT */
#define CONFIG_SPL_TEXT_BASE 0x10000000
@@ -52,7 +52,6 @@
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500
#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1d000
@@ -61,7 +61,6 @@
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500
#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1f000 /* 124 KiB */
#define CONFIG_SPL_STACK 0x10020000
@@ -52,7 +52,6 @@
#define CONFIG_OMAP_HSMMC
/* SPL */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -170,7 +170,6 @@
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -40,8 +40,6 @@
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
-
#define CONFIG_PHY_ATHEROS
#define CONFIG_FACTORYSET
@@ -48,8 +48,6 @@
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
-
#undef CONFIG_MII
#undef CONFIG_PHY_GIGE
#define CONFIG_PHY_SMSC
@@ -35,8 +35,6 @@
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200
-
#define CONFIG_PHY_NATSEMI
#define CONFIG_FACTORYSET
@@ -111,7 +111,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -128,7 +128,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -167,7 +167,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -127,7 +127,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -125,7 +125,6 @@
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -276,7 +276,6 @@
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -41,8 +41,6 @@
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
-
#undef CONFIG_MII
#undef CONFIG_PHY_GIGE
#define CONFIG_PHY_SMSC
@@ -161,7 +161,6 @@
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -125,7 +125,6 @@
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -235,9 +235,6 @@
#endif
-/* RAW SD card / eMMC locations. */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-
/* FAT sd card locations. */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
@@ -23,7 +23,6 @@
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm1136/u-boot-spl.lds"
#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 /* 512 KB */
#define CONFIG_SPL_TEXT_BASE 0x10002300
#define CONFIG_SPL_MAX_SIZE (64 * 1024) /* 8 KB for stack */
@@ -296,7 +296,6 @@
/* MMC support */
#ifdef CONFIG_ZYNQ_SDHCI
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#endif
@@ -7830,7 +7830,6 @@ CONFIG_SYS_USE_SERIALFLASH
CONFIG_SYS_USE_SPIFLASH
CONFIG_SYS_USE_UBI
CONFIG_SYS_USR_EXCEP
-CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
CONFIG_SYS_U_BOOT_OFFS
CONFIG_SYS_VA_BITS
CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR
This option isn't used for anything, so get rid of it. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> --- Changes in v2: None README | 4 ---- include/configs/am3517_crane.h | 1 - include/configs/am3517_evm.h | 1 - include/configs/at91sam9m10g45ek.h | 1 - include/configs/at91sam9n12ek.h | 1 - include/configs/at91sam9x5ek.h | 1 - include/configs/brppt1.h | 2 -- include/configs/brxre1.h | 2 -- include/configs/clearfog.h | 1 - include/configs/cm_fx6.h | 1 - include/configs/cm_t35.h | 1 - include/configs/cm_t54.h | 5 ----- include/configs/db-88f6820-gp.h | 1 - include/configs/draco.h | 2 -- include/configs/etamin.h | 2 -- include/configs/imx6_spl.h | 3 +-- include/configs/ls1021aqds.h | 1 - include/configs/ls1021atwr.h | 6 +----- include/configs/ls1043a_common.h | 1 - include/configs/ls1046a_common.h | 1 - include/configs/omap3_evm.h | 1 - include/configs/picosam9g45.h | 1 - include/configs/pxm2.h | 2 -- include/configs/rastaban.h | 2 -- include/configs/rut.h | 2 -- include/configs/sama5d2_xplained.h | 1 - include/configs/sama5d3_xplained.h | 1 - include/configs/sama5d3xek.h | 1 - include/configs/sama5d4_xplained.h | 1 - include/configs/sama5d4ek.h | 1 - include/configs/tao3530.h | 1 - include/configs/thuban.h | 2 -- include/configs/ti814x_evm.h | 1 - include/configs/ti816x_evm.h | 1 - include/configs/ti_armv7_common.h | 3 --- include/configs/woodburn_sd.h | 1 - include/configs/zynq-common.h | 1 - scripts/config_whitelist.txt | 1 - 38 files changed, 2 insertions(+), 60 deletions(-) -- 2.9.3 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot