@@ -3,10 +3,477 @@
* Copyright (c) 2024, Linaro Limited
*/
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
/ {
+ thermal-zones {
+ pm8550-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-2-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_2_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-3-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_3_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-4-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_4_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-5-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_5_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-6-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_6_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-8-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_8_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-9-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_9_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8010-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8010_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus0 {
+ /* PMK8380 */
+ pmk8550: pmic@0 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmk8550_pon: pon@1300 {
+ compatible = "qcom,pmk8350-pon";
+ reg = <0x1300>, <0x800>;
+ reg-names = "hlos", "pbs";
+
+ pon_pwrkey: pwrkey {
+ compatible = "qcom,pmk8350-pwrkey";
+ interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_POWER>;
+ };
+
+ pon_resin: resin {
+ compatible = "qcom,pmk8350-resin";
+ interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+ status = "disabled";
+ };
+ };
+
+ pmk8550_rtc: rtc@6100 {
+ compatible = "qcom,pmk8350-rtc";
+ reg = <0x6100>, <0x6200>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+ /* Not yet sure what blocks access */
+ status = "reserved";
+ };
+
+ pmk8550_sdam_2: nvram@7100 {
+ compatible = "qcom,spmi-sdam";
+ reg = <0x7100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x7100 0x100>;
+
+ reboot_reason: reboot-reason@48 {
+ reg = <0x48 0x1>;
+ bits = <1 7>;
+ };
+ };
+
+ pmk8550_gpios: gpio@8800 {
+ compatible = "qcom,pmk8550-gpio", "qcom,spmi-gpio";
+ reg = <0xb800>;
+ gpio-controller;
+ gpio-ranges = <&pmk8550_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380C */
+ pm8550: pmic@1 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550_gpios: gpio@8800 {
+ compatible = "qcom,pm8550-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pm8550_flash: led-controller@ee00 {
+ compatible = "qcom,pm8550-flash-led", "qcom,spmi-flash-led";
+ reg = <0xee00>;
+ status = "disabled";
+ };
+
+ pm8550_pwm: pwm {
+ compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm";
+ #pwm-cells = <2>;
+
+ status = "disabled";
+ };
+ };
+
+ /* PMC8380VE */
+ pm8550ve_2: pmic@2 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_2_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_2_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_2_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380 is actually not a PM8550 series rebrand */
+ pmc8380_3: pmic@3 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_3_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_3_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_3_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8380_4: pmic@4 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_4_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_4_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_4_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8380_5: pmic@5 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_5_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_5_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_5_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8380_6: pmic@6 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_6_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_6_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_6_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380VE */
+ pm8550ve_8: pmic@8 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_8_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x8 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_8_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_8_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380VE */
+ pm8550ve_9: pmic@9 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x9 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_9_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_9_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_9_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8010: pmic@c {
+ compatible = "qcom,pm8010", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8010_temp_alarm: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
};
&spmi_bus1 {
@@ -48,4 +515,17 @@ smb2360_2_eusb2_repeater: phy@fd00 {
#phy-cells = <0>;
};
};
+
+ smb2360_3: pmic@c {
+ compatible = "qcom,smb2360", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb2360_3_eusb2_repeater: phy@fd00 {
+ compatible = "qcom,smb2360-eusb2-repeater";
+ reg = <0xfd00>;
+ #phy-cells = <0>;
+ };
+ };
};
During the initial bringup, all of the peripherals on non-SMB PMICs were either not used, or were not necessary to accomplish certain goals. This however, left a hole in the hardware description. Add the missing ones. Note that the PM8010 errors out on reads on the CRD (works fine on the QCP) for reasons unknown, but that shall be ironed out in the future.. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi | 480 +++++++++++++++++++++++++++ 1 file changed, 480 insertions(+)