@@ -150,6 +150,7 @@ CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_DW=y
CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_ACPI_PLATFORM=y
CONFIG_SERIAL_SH_SCI=y
CONFIG_SERIAL_EARLYCON_RISCV_SBI=y
CONFIG_VIRTIO_CONSOLE=y
new file mode 100644
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Serial Port driver for ACPI platform devices
+ *
+ * This driver is for generic 16550 compatible UART enumerated via ACPI
+ * platform bus instead of PNP bus like PNP0501. This is not a full
+ * driver but mostly provides the ACPI wrapper and uses generic
+ * 8250 framework for rest of the functionality.
+ */
+
+#include <linux/acpi.h>
+#include <linux/serial_reg.h>
+#include <linux/serial_8250.h>
+
+#include "8250.h"
+
+struct acpi_serial_info {
+ int line;
+};
+
+static int acpi_platform_serial_probe(struct platform_device *pdev)
+{
+ struct acpi_serial_info *data;
+ struct uart_8250_port port8250;
+ struct device *dev = &pdev->dev;
+ struct resource *regs;
+
+ int ret, irq;
+
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!regs) {
+ dev_err(dev, "no registers defined\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ memset(&port8250, 0, sizeof(port8250));
+
+ spin_lock_init(&port8250.port.lock);
+
+ port8250.port.mapbase = regs->start;
+ port8250.port.irq = irq;
+ port8250.port.type = PORT_16550A;
+ port8250.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT |
+ UPF_IOREMAP | UPF_FIXED_TYPE;
+ port8250.port.dev = dev;
+ port8250.port.mapsize = resource_size(regs);
+ port8250.port.iotype = UPIO_MEM;
+ port8250.port.irqflags = IRQF_SHARED;
+
+ port8250.port.membase = devm_ioremap(dev, port8250.port.mapbase, port8250.port.mapsize);
+ if (!port8250.port.membase)
+ return -ENOMEM;
+
+ ret = uart_read_and_validate_port_properties(&port8250.port);
+ if (ret)
+ return -EINVAL;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->line = serial8250_register_8250_port(&port8250);
+ if (data->line < 0)
+ return data->line;
+
+ platform_set_drvdata(pdev, data);
+ return 0;
+}
+
+static void acpi_platform_serial_remove(struct platform_device *pdev)
+{
+ struct acpi_serial_info *data = platform_get_drvdata(pdev);
+
+ serial8250_unregister_port(data->line);
+}
+
+static const struct acpi_device_id acpi_platform_serial_table[] = {
+ { "RSCV0003", 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(acpi, acpi_platform_serial_table);
+
+static struct platform_driver acpi_platform_serial_driver = {
+ .driver = {
+ .name = "acpi_serial",
+ .acpi_match_table = ACPI_PTR(acpi_platform_serial_table),
+ },
+ .probe = acpi_platform_serial_probe,
+ .remove_new = acpi_platform_serial_remove,
+};
+
+builtin_platform_driver(acpi_platform_serial_driver);
@@ -576,3 +576,11 @@ config SERIAL_OF_PLATFORM
are probed through devicetree, including Open Firmware based
PowerPC systems and embedded systems on architectures using the
flattened device tree format.
+
+config SERIAL_ACPI_PLATFORM
+ tristate "ACPI platform bus based probing for 8250 ports"
+ depends on SERIAL_8250 && ACPI
+ default n
+ help
+ This option is used for generic 8250 compatible serial ports
+ that are enumerated through ACPI platform bus.
@@ -18,6 +18,7 @@ obj-$(CONFIG_SERIAL_8250_CONSOLE) += 8250_early.o
obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o
obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o
+obj-$(CONFIG_SERIAL_ACPI_PLATFORM) += 8250_acpi.o
obj-$(CONFIG_SERIAL_8250_ASPEED_VUART) += 8250_aspeed_vuart.o
obj-$(CONFIG_SERIAL_8250_BCM2835AUX) += 8250_bcm2835aux.o
obj-$(CONFIG_SERIAL_8250_BCM7271) += 8250_bcm7271.o
RISC-V has non-PNP generic 16550A compatible UART which needs to be enumerated as ACPI platform device. Add driver support for such devices similar to 8250_of. The driver is enabled when the CONFIG_SERIAL_ACPI_PLATFORM option is enabled. Enable this option for RISC-V. Signed-off-by: Sunil V L <sunilvl@ventanamicro.com> --- arch/riscv/configs/defconfig | 1 + drivers/tty/serial/8250/8250_acpi.c | 96 +++++++++++++++++++++++++++++ drivers/tty/serial/8250/Kconfig | 8 +++ drivers/tty/serial/8250/Makefile | 1 + 4 files changed, 106 insertions(+) create mode 100644 drivers/tty/serial/8250/8250_acpi.c