@@ -11,6 +11,8 @@ obj-$(CONFIG_MACH_U8500) += board-mop500.o board-mop500-sdi.o \
board-mop500-uib.o board-mop500-stuib.o \
board-mop500-u8500uib.o \
board-mop500-pins.o
+obj-$(CONFIG_MACH_U8500_SNOWBALL) += board-snowball.o \
+ board-mop500-regulators.o
obj-$(CONFIG_MACH_U5500) += board-u5500.o board-u5500-sdi.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
new file mode 100644
@@ -0,0 +1,355 @@
+/*
+ * Copyright (C) 2010-2011 ST-Ericsson
+ *
+ * Author: Mathieu Poirier <mathieu.poirier@linaro.org>, based on
+ * the work of Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/pl022.h>
+#include <linux/amba/serial.h>
+#include <linux/spi/spi.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/input.h>
+#include <linux/smsc911x.h>
+#include <linux/gpio_keys.h>
+#include <linux/leds.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <plat/i2c.h>
+#include <plat/ste_dma40.h>
+
+#include <mach/hardware.h>
+#include <mach/setup.h>
+#include <mach/devices.h>
+#include <mach/irqs.h>
+
+#include "ste-dma40-db8500.h"
+#include "devices-db8500.h"
+#include "board-mop500.h"
+#include "board-mop500-regulators.h"
+
+static struct gpio_led snowball_led_array[] = {
+ {
+ .name = "user_led",
+ .default_trigger = "none",
+ .gpio = 142,
+ },
+};
+
+static struct gpio_led_platform_data snowball_led_data = {
+ .leds = snowball_led_array,
+ .num_leds = ARRAY_SIZE(snowball_led_array),
+};
+
+static struct smsc911x_platform_config sbnet_cfg = {
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
+ .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
+ .flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
+};
+
+static struct platform_device snowball_led_dev = {
+ .name = "leds-gpio",
+ .dev = {
+ .platform_data = &snowball_led_data,
+ },
+};
+
+static struct gpio_keys_button snowball_key_array[] = {
+ {
+ .gpio = 32,
+ .type = EV_KEY,
+ .code = KEY_1,
+ .desc = "userpb",
+ .active_low = 1,
+ .debounce_interval = 50,
+ .wakeup = 1,
+ },
+ {
+ .gpio = 151,
+ .type = EV_KEY,
+ .code = KEY_2,
+ .desc = "extkb1",
+ .active_low = 1,
+ .debounce_interval = 50,
+ .wakeup = 1,
+ },
+ {
+ .gpio = 152,
+ .type = EV_KEY,
+ .code = KEY_3,
+ .desc = "extkb2",
+ .active_low = 1,
+ .debounce_interval = 50,
+ .wakeup = 1,
+ },
+ {
+ .gpio = 161,
+ .type = EV_KEY,
+ .code = KEY_4,
+ .desc = "extkb3",
+ .active_low = 1,
+ .debounce_interval = 50,
+ .wakeup = 1,
+ },
+ {
+ .gpio = 162,
+ .type = EV_KEY,
+ .code = KEY_5,
+ .desc = "extkb4",
+ .active_low = 1,
+ .debounce_interval = 50,
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data snowball_key_data = {
+ .buttons = snowball_key_array,
+ .nbuttons = ARRAY_SIZE(snowball_key_array),
+};
+
+static struct platform_device snowball_key_dev = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &snowball_key_data,
+ }
+};
+
+static struct resource sbnet_res[] = {
+ {
+ .name = "smsc911x-memory",
+ .start = (0x5000 << 16),
+ .end = (0x5000 << 16) + 0x3ff,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = NOMADIK_GPIO_TO_IRQ(140),
+ .end = NOMADIK_GPIO_TO_IRQ(140),
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+ },
+};
+
+static struct platform_device sbnet_dev = {
+ .name = "smsc911x",
+ .num_resources = ARRAY_SIZE(sbnet_res),
+ .resource = sbnet_res,
+ .dev = {
+ .platform_data = &sbnet_cfg,
+ },
+};
+
+static struct ab8500_platform_data ab8500_platdata = {
+ .irq_base = MOP500_AB8500_IRQ_BASE,
+ .regulator = ab8500_regulators,
+ .num_regulator = ARRAY_SIZE(ab8500_regulators),
+};
+
+static struct resource ab8500_resources[] = {
+ [0] = {
+ .start = IRQ_DB8500_AB8500,
+ .end = IRQ_DB8500_AB8500,
+ .flags = IORESOURCE_IRQ
+ }
+};
+
+struct platform_device ab8500_device_snowball = {
+ .name = "ab8500-i2c",
+ .id = 0,
+ .dev = {
+ .platform_data = &ab8500_platdata,
+ },
+ .num_resources = 1,
+ .resource = ab8500_resources,
+};
+
+#define U8500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \
+static struct nmk_i2c_controller u8500_i2c##id##_data = { \
+ /* \
+ * slave data setup time, which is \
+ * 250 ns,100ns,10ns which is 14,6,2 \
+ * respectively for a 48 Mhz \
+ * i2c clock \
+ */ \
+ .slsu = _slsu, \
+ /* Tx FIFO threshold */ \
+ .tft = _tft, \
+ /* Rx FIFO threshold */ \
+ .rft = _rft, \
+ /* std. mode operation */ \
+ .clk_freq = clk, \
+ .sm = _sm, \
+}
+
+/*
+ * The board uses 4 i2c controllers, initialize all of
+ * them with slave data setup time of 250 ns,
+ * Tx & Rx FIFO threshold values as 1 and standard
+ * mode of operation
+ */
+U8500_I2C_CONTROLLER(0, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+U8500_I2C_CONTROLLER(1, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+U8500_I2C_CONTROLLER(2, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+U8500_I2C_CONTROLLER(3, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
+
+static void __init mop500_i2c_init(void)
+{
+ db8500_add_i2c0(&u8500_i2c0_data);
+ db8500_add_i2c1(&u8500_i2c1_data);
+ db8500_add_i2c2(&u8500_i2c2_data);
+ db8500_add_i2c3(&u8500_i2c3_data);
+}
+
+static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_PERIPH_TO_MEM,
+ .src_dev_type = DB8500_DMA_DEV8_SSP0_RX,
+ .dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_MEM_TO_PERIPH,
+ .src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+ .dst_dev_type = DB8500_DMA_DEV8_SSP0_TX,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct pl022_ssp_controller ssp0_platform_data = {
+ .bus_id = 0,
+ .enable_dma = 1,
+ .dma_filter = stedma40_filter,
+ .dma_rx_param = &ssp0_dma_cfg_rx,
+ .dma_tx_param = &ssp0_dma_cfg_tx,
+
+ /* on this platform, gpio 31,142,144,214 &
+ * 224 are connected as chip selects
+ */
+ .num_chipselect = 5,
+};
+
+static void __init mop500_spi_init(void)
+{
+ db8500_add_ssp0(&ssp0_platform_data);
+}
+
+static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_PERIPH_TO_MEM,
+ .src_dev_type = DB8500_DMA_DEV13_UART0_RX,
+ .dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_MEM_TO_PERIPH,
+ .src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+ .dst_dev_type = DB8500_DMA_DEV13_UART0_TX,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_PERIPH_TO_MEM,
+ .src_dev_type = DB8500_DMA_DEV12_UART1_RX,
+ .dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_MEM_TO_PERIPH,
+ .src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+ .dst_dev_type = DB8500_DMA_DEV12_UART1_TX,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_PERIPH_TO_MEM,
+ .src_dev_type = DB8500_DMA_DEV11_UART2_RX,
+ .dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_MEM_TO_PERIPH,
+ .src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+ .dst_dev_type = DB8500_DMA_DEV11_UART2_TX,
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct amba_pl011_data uart0_plat = {
+ .dma_filter = stedma40_filter,
+ .dma_rx_param = &uart0_dma_cfg_rx,
+ .dma_tx_param = &uart0_dma_cfg_tx,
+};
+
+static struct amba_pl011_data uart1_plat = {
+ .dma_filter = stedma40_filter,
+ .dma_rx_param = &uart1_dma_cfg_rx,
+ .dma_tx_param = &uart1_dma_cfg_tx,
+};
+
+static struct amba_pl011_data uart2_plat = {
+ .dma_filter = stedma40_filter,
+ .dma_rx_param = &uart2_dma_cfg_rx,
+ .dma_tx_param = &uart2_dma_cfg_tx,
+};
+
+static void __init mop500_uart_init(void)
+{
+ db8500_add_uart0(&uart0_plat);
+ db8500_add_uart1(&uart1_plat);
+ db8500_add_uart2(&uart2_plat);
+}
+
+static struct platform_device *snowball_devices[] __initdata = {
+ &snowball_led_dev,
+ &snowball_key_dev,
+ &sbnet_dev,
+ &ab8500_device_snowball,
+};
+
+static void __init mop500_init_machine(void)
+{
+ u8500_init_devices();
+
+ mop500_i2c_init();
+ mop500_spi_init();
+ mop500_uart_init();
+
+ platform_add_devices(snowball_devices, ARRAY_SIZE(snowball_devices));
+}
+
+MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
+ .boot_params = 0x100,
+ .map_io = u8500_map_io,
+ .init_irq = ux500_init_irq,
+ /* we re-use nomadik timer here */
+ .timer = &ux500_timer,
+ .init_machine = mop500_init_machine,
+MACHINE_END