@@ -6503,6 +6503,57 @@ ath12k_mac_change_chanctx_fill_iter(void *data, u8 *mac,
arg->next_vif++;
}
+static u32 ath12k_mac_nlwidth_to_wmiwidth(enum nl80211_chan_width width)
+{
+ switch (width) {
+ case NL80211_CHAN_WIDTH_20:
+ return WMI_CHAN_WIDTH_20;
+ case NL80211_CHAN_WIDTH_40:
+ return WMI_CHAN_WIDTH_40;
+ case NL80211_CHAN_WIDTH_80:
+ return WMI_CHAN_WIDTH_80;
+ case NL80211_CHAN_WIDTH_160:
+ return WMI_CHAN_WIDTH_160;
+ case NL80211_CHAN_WIDTH_80P80:
+ return WMI_CHAN_WIDTH_80P80;
+ case NL80211_CHAN_WIDTH_5:
+ return WMI_CHAN_WIDTH_5;
+ case NL80211_CHAN_WIDTH_10:
+ return WMI_CHAN_WIDTH_10;
+ case NL80211_CHAN_WIDTH_320:
+ return WMI_CHAN_WIDTH_320;
+ default:
+ WARN_ON(1);
+ return WMI_CHAN_WIDTH_20;
+ }
+}
+
+static int ath12k_mac_update_peer_puncturing_width(struct ath12k *ar,
+ struct ath12k_vif *arvif,
+ struct cfg80211_chan_def def)
+{
+ u32 param_id, param_value;
+ int ret;
+
+ if (arvif->vdev_type != WMI_VDEV_TYPE_STA)
+ return 0;
+
+ param_id = WMI_PEER_CHWIDTH_PUNCTURE_20MHZ_BITMAP;
+ param_value = ath12k_mac_nlwidth_to_wmiwidth(def.width) |
+ u32_encode_bits((~def.punctured),
+ WMI_PEER_PUNCTURE_BITMAP);
+
+ ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+ "Set puncturing bitmap %02x and width %d for vdev: %d\n",
+ def.punctured, def.width, arvif->vdev_id);
+
+ ret = ath12k_wmi_set_peer_param(ar, arvif->bssid,
+ arvif->vdev_id, param_id,
+ param_value);
+
+ return ret;
+}
+
static void
ath12k_mac_update_vif_chan(struct ath12k *ar,
struct ieee80211_vif_chanctx_switch *vifs,
@@ -6595,6 +6646,16 @@ ath12k_mac_update_vif_chan(struct ath12k *ar,
arvif->vdev_id, ret);
continue;
}
+
+ ret = ath12k_mac_update_peer_puncturing_width(arvif->ar, arvif,
+ vifs[i].new_ctx->def);
+ if (ret) {
+ ath12k_warn(ar->ab,
+ "failed to update puncturing bitmap %02x and width %d: %d\n",
+ vifs[i].new_ctx->def.punctured,
+ vifs[i].new_ctx->def.width, ret);
+ continue;
+ }
}
/* Restart the internal monitor vdev on new channel */
@@ -2195,8 +2195,11 @@ enum wmi_peer_param {
WMI_PEER_SET_MAX_TX_RATE = 17,
WMI_PEER_SET_MIN_TX_RATE = 18,
WMI_PEER_SET_DEFAULT_ROUTING = 19,
+ WMI_PEER_CHWIDTH_PUNCTURE_20MHZ_BITMAP = 39,
};
+#define WMI_PEER_PUNCTURE_BITMAP GENMASK(23, 8)
+
enum wmi_slot_time {
WMI_VDEV_SLOT_TIME_LONG = 1,
WMI_VDEV_SLOT_TIME_SHORT = 2,
@@ -2600,6 +2603,19 @@ struct ath12k_wmi_soc_hal_reg_caps_params {
__le32 num_phy;
} __packed;
+enum wmi_channel_width {
+ WMI_CHAN_WIDTH_20 = 0,
+ WMI_CHAN_WIDTH_40 = 1,
+ WMI_CHAN_WIDTH_80 = 2,
+ WMI_CHAN_WIDTH_160 = 3,
+ WMI_CHAN_WIDTH_80P80 = 4,
+ WMI_CHAN_WIDTH_5 = 5,
+ WMI_CHAN_WIDTH_10 = 6,
+ WMI_CHAN_WIDTH_165 = 7,
+ WMI_CHAN_WIDTH_160P160 = 8,
+ WMI_CHAN_WIDTH_320 = 9,
+};
+
#define WMI_MAX_EHTCAP_MAC_SIZE 2
#define WMI_MAX_EHTCAP_PHY_SIZE 3
#define WMI_MAX_EHTCAP_RATE_SET 3
Every time EHT Operation element changed, mac80211 will parse it and extract the valid puncturing bitmap according to the bandwidth. Current driver only update puncturing bitmap to firmware as vdev parameter. Which can only meet the needs of AP. But STA will also use it as peer parameter. If only update as vdev parameter, might cause firmware crash. QCN9274 is the same. So update bandwidth and puncturing bitmap as peer parameters once they changed for STA. Then send them to the firmware by WMI event. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> --- v2: 1. remove mac80211 patch because it is merged. 2. add station mode judgment. 3. rebased on tag: ath-202404051226. --- drivers/net/wireless/ath/ath12k/mac.c | 61 +++++++++++++++++++++++++++ drivers/net/wireless/ath/ath12k/wmi.h | 16 +++++++ 2 files changed, 77 insertions(+)