new file mode 100644
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/linear_range.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#include <linux/mfd/88pm886.h>
+
+#define PM886_PAGE_OFFSET_REGULATORS 1
+
+#define PM886_REG_LDO_EN1 0x09
+#define PM886_REG_LDO_EN2 0x0a
+
+#define PM886_REG_BUCK_EN 0x08
+
+#define PM886_REG_LDO1_VOUT 0x20
+#define PM886_REG_LDO2_VOUT 0x26
+#define PM886_REG_LDO3_VOUT 0x2c
+#define PM886_REG_LDO4_VOUT 0x32
+#define PM886_REG_LDO5_VOUT 0x38
+#define PM886_REG_LDO6_VOUT 0x3e
+#define PM886_REG_LDO7_VOUT 0x44
+#define PM886_REG_LDO8_VOUT 0x4a
+#define PM886_REG_LDO9_VOUT 0x50
+#define PM886_REG_LDO10_VOUT 0x56
+#define PM886_REG_LDO11_VOUT 0x5c
+#define PM886_REG_LDO12_VOUT 0x62
+#define PM886_REG_LDO13_VOUT 0x68
+#define PM886_REG_LDO14_VOUT 0x6e
+#define PM886_REG_LDO15_VOUT 0x74
+#define PM886_REG_LDO16_VOUT 0x7a
+
+#define PM886_REG_BUCK1_VOUT 0xa5
+#define PM886_REG_BUCK2_VOUT 0xb3
+#define PM886_REG_BUCK3_VOUT 0xc1
+#define PM886_REG_BUCK4_VOUT 0xcf
+#define PM886_REG_BUCK5_VOUT 0xdd
+
+#define PM886_LDO_VSEL_MASK 0x0f
+#define PM886_BUCK_VSEL_MASK 0x7f
+
+struct pm886_regulator {
+ struct regulator_desc desc;
+ int max_uA;
+};
+
+static int pm886_regulator_get_ilim(struct regulator_dev *rdev)
+{
+ struct pm886_regulator *data = rdev_get_drvdata(rdev);
+
+ if (!data) {
+ dev_err(&rdev->dev, "Failed to get regulator data\n");
+ return -EINVAL;
+ }
+ return data->max_uA;
+}
+
+static const struct regulator_ops pm886_ldo_ops = {
+ .list_voltage = regulator_list_voltage_table,
+ .map_voltage = regulator_map_voltage_iterate,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_current_limit = pm886_regulator_get_ilim,
+};
+
+static const struct regulator_ops pm886_buck_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_current_limit = pm886_regulator_get_ilim,
+};
+
+static const unsigned int pm886_ldo_volt_table1[] = {
+ 1700000, 1800000, 1900000, 2500000, 2800000, 2900000, 3100000, 3300000,
+};
+
+static const unsigned int pm886_ldo_volt_table2[] = {
+ 1200000, 1250000, 1700000, 1800000, 1850000, 1900000, 2500000, 2600000,
+ 2700000, 2750000, 2800000, 2850000, 2900000, 3000000, 3100000, 3300000,
+};
+
+static const unsigned int pm886_ldo_volt_table3[] = {
+ 1700000, 1800000, 1900000, 2000000, 2100000, 2500000, 2700000, 2800000,
+};
+
+static const struct linear_range pm886_buck_volt_ranges1[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0, 79, 12500),
+ REGULATOR_LINEAR_RANGE(1600000, 80, 84, 50000),
+};
+
+static const struct linear_range pm886_buck_volt_ranges2[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0, 79, 12500),
+ REGULATOR_LINEAR_RANGE(1600000, 80, 114, 50000),
+};
+
+static struct pm886_regulator pm886_regulators[] = {
+ {
+ .desc = {
+ .name = "LDO2",
+ .regulators_node = "regulators",
+ .of_match = "ldo2",
+ .ops = &pm886_ldo_ops,
+ .type = REGULATOR_VOLTAGE,
+ .enable_reg = PM886_REG_LDO_EN1,
+ .enable_mask = BIT(1),
+ .volt_table = pm886_ldo_volt_table1,
+ .n_voltages = ARRAY_SIZE(pm886_ldo_volt_table1),
+ .vsel_reg = PM886_REG_LDO2_VOUT,
+ .vsel_mask = PM886_LDO_VSEL_MASK,
+ },
+ .max_uA = 100000,
+ },
+ {
+ .desc = {
+ .name = "LDO15",
+ .regulators_node = "regulators",
+ .of_match = "ldo15",
+ .ops = &pm886_ldo_ops,
+ .type = REGULATOR_VOLTAGE,
+ .enable_reg = PM886_REG_LDO_EN2,
+ .enable_mask = BIT(6),
+ .volt_table = pm886_ldo_volt_table2,
+ .n_voltages = ARRAY_SIZE(pm886_ldo_volt_table2),
+ .vsel_reg = PM886_REG_LDO15_VOUT,
+ .vsel_mask = PM886_LDO_VSEL_MASK,
+ },
+ .max_uA = 200000,
+ },
+ {
+ .desc = {
+ .name = "buck2",
+ .regulators_node = "regulators",
+ .of_match = "buck2",
+ .ops = &pm886_buck_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = 115,
+ .linear_ranges = pm886_buck_volt_ranges2,
+ .n_linear_ranges = ARRAY_SIZE(pm886_buck_volt_ranges2),
+ .vsel_reg = PM886_REG_BUCK2_VOUT,
+ .vsel_mask = PM886_BUCK_VSEL_MASK,
+ .enable_reg = PM886_REG_BUCK_EN,
+ .enable_mask = BIT(1),
+ },
+ .max_uA = 1200000,
+ },
+};
+
+static int pm886_regulator_probe(struct platform_device *pdev)
+{
+ struct pm886_chip *chip = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config rcfg = { };
+ struct pm886_regulator *regulator;
+ struct device *dev = &pdev->dev;
+ struct regulator_desc *rdesc;
+ struct regulator_dev *rdev;
+ struct i2c_client *page;
+ struct regmap *regmap;
+
+ page = devm_i2c_new_dummy_device(dev, chip->client->adapter,
+ chip->client->addr + PM886_PAGE_OFFSET_REGULATORS);
+ if (IS_ERR(page))
+ return dev_err_probe(dev, PTR_ERR(page),
+ "Failed to initialize regulators client\n");
+
+ regmap = devm_regmap_init_i2c(page, &pm886_i2c_regmap);
+ if (IS_ERR(regmap))
+ return dev_err_probe(dev, PTR_ERR(regmap),
+ "Failed to initialize regulators regmap\n");
+ rcfg.regmap = regmap;
+
+ rcfg.dev = dev->parent;
+
+ for (int i = 0; i < ARRAY_SIZE(pm886_regulators); i++) {
+ regulator = &pm886_regulators[i];
+ rdesc = ®ulator->desc;
+ rcfg.driver_data = regulator;
+ rdev = devm_regulator_register(dev, rdesc, &rcfg);
+ if (IS_ERR(rdev))
+ return dev_err_probe(dev, PTR_ERR(rdev),
+ "Failed to register %s\n", rdesc->name);
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id pm886_regulator_id_table[] = {
+ { "88pm886-regulator", },
+ { }
+};
+MODULE_DEVICE_TABLE(platform, pm886_regulator_id_table);
+
+static struct platform_driver pm886_regulator_driver = {
+ .driver = {
+ .name = "88pm886-regulator",
+ },
+ .probe = pm886_regulator_probe,
+ .id_table = pm886_regulator_id_table,
+};
+module_platform_driver(pm886_regulator_driver);
+
+MODULE_DESCRIPTION("Marvell 88PM886 PMIC regulator driver");
+MODULE_AUTHOR("Karel Balej <balejk@matfyz.cz>");
+MODULE_LICENSE("GPL");
@@ -91,6 +91,12 @@ config REGULATOR_88PM8607
help
This driver supports 88PM8607 voltage regulator chips.
+config REGULATOR_88PM886
+ tristate "Marvell 88PM886 voltage regulators"
+ depends on MFD_88PM886_PMIC
+ help
+ This driver implements support for Marvell 88PM886 voltage regulators.
+
config REGULATOR_ACT8865
tristate "Active-semi act8865 voltage regulator"
depends on I2C
@@ -14,6 +14,7 @@ obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o
obj-$(CONFIG_REGULATOR_88PG86X) += 88pg86x.o
obj-$(CONFIG_REGULATOR_88PM800) += 88pm800-regulator.o
obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o
+obj-$(CONFIG_REGULATOR_88PM886) += 88pm886-regulator.o
obj-$(CONFIG_REGULATOR_CROS_EC) += cros-ec-regulator.o
obj-$(CONFIG_REGULATOR_CPCAP) += cpcap-regulator.o
obj-$(CONFIG_REGULATOR_AAT2870) += aat2870-regulator.o