| Message ID | 20240215-b4-qcom-common-target-v4-34-ed06355c634a@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Qualcomm generic board support | expand |
On Fri, 16 Feb 2024 at 02:23, Caleb Connolly <caleb.connolly@linaro.org> wrote: > > Import PM8994 and PMI8994 DTSI files in preparation for switching > MSM8996 boards to upstream DTS. > > Taken from kernel tag v6.7 > > Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> > Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> > --- > arch/arm/dts/pm8994.dtsi | 152 ++++++++++++++++++++++++++++++++++++++++++++++ > arch/arm/dts/pmi8994.dtsi | 65 ++++++++++++++++++++ > 2 files changed, 217 insertions(+) > Reviewed-by: Sumit Garg <sumit.garg@linaro.org> -Sumit > diff --git a/arch/arm/dts/pm8994.dtsi b/arch/arm/dts/pm8994.dtsi > new file mode 100644 > index 000000000000..d44a95caf04a > --- /dev/null > +++ b/arch/arm/dts/pm8994.dtsi > @@ -0,0 +1,152 @@ > +// SPDX-License-Identifier: GPL-2.0 > +#include <dt-bindings/iio/qcom,spmi-vadc.h> > +#include <dt-bindings/input/linux-event-codes.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +/ { > + thermal-zones { > + pm8994-thermal { > + polling-delay-passive = <250>; > + polling-delay = <1000>; > + > + thermal-sensors = <&pm8994_temp>; > + > + trips { > + pm8994_alert0: pm8994-alert0 { > + temperature = <95000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + pm8994_crit: pm8994-crit { > + temperature = <125000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + }; > + }; > +}; > + > +&spmi_bus { > + > + pmic@0 { > + compatible = "qcom,pm8994", "qcom,spmi-pmic"; > + reg = <0x0 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + rtc@6000 { > + compatible = "qcom,pm8941-rtc"; > + reg = <0x6000>, <0x6100>; > + reg-names = "rtc", "alarm"; > + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; > + }; > + > + pm8994_pon: pon@800 { > + compatible = "qcom,pm8916-pon"; > + reg = <0x800>; > + mode-bootloader = <0x2>; > + mode-recovery = <0x1>; > + > + pwrkey { > + compatible = "qcom,pm8941-pwrkey"; > + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + bias-pull-up; > + linux,code = <KEY_POWER>; > + }; > + > + pm8994_resin: resin { > + compatible = "qcom,pm8941-resin"; > + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + bias-pull-up; > + status = "disabled"; > + }; > + }; > + > + pm8994_temp: temp-alarm@2400 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0x2400>; > + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; > + io-channels = <&pm8994_vadc VADC_DIE_TEMP>; > + io-channel-names = "thermal"; > + #thermal-sensor-cells = <0>; > + }; > + > + pm8994_vadc: adc@3100 { > + compatible = "qcom,spmi-vadc"; > + reg = <0x3100>; > + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + > + channel@7 { > + reg = <VADC_VSYS>; > + qcom,pre-scaling = <1 3>; > + label = "vph_pwr"; > + }; > + channel@8 { > + reg = <VADC_DIE_TEMP>; > + label = "die_temp"; > + }; > + channel@9 { > + reg = <VADC_REF_625MV>; > + label = "ref_625mv"; > + }; > + channel@a { > + reg = <VADC_REF_1250MV>; > + label = "ref_1250mv"; > + }; > + channel@e { > + reg = <VADC_GND_REF>; > + }; > + channel@f { > + reg = <VADC_VDD_VADC>; > + }; > + }; > + > + pm8994_gpios: gpio@c000 { > + compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio"; > + reg = <0xc000>; > + gpio-controller; > + gpio-ranges = <&pm8994_gpios 0 0 22>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + pm8994_mpps: mpps@a000 { > + compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp"; > + reg = <0xa000>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pm8994_mpps 0 0 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > + pmic@1 { > + compatible = "qcom,pm8994", "qcom,spmi-pmic"; > + reg = <0x1 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pm8994_lpg: pwm { > + compatible = "qcom,pm8994-lpg"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + #pwm-cells = <2>; > + > + status = "disabled"; > + }; > + > + pm8994_spmi_regulators: regulators { > + compatible = "qcom,pm8994-regulators"; > + }; > + }; > +}; > diff --git a/arch/arm/dts/pmi8994.dtsi b/arch/arm/dts/pmi8994.dtsi > new file mode 100644 > index 000000000000..36d6a1fb553a > --- /dev/null > +++ b/arch/arm/dts/pmi8994.dtsi > @@ -0,0 +1,65 @@ > +// SPDX-License-Identifier: GPL-2.0 > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +&spmi_bus { > + > + pmic@2 { > + compatible = "qcom,pmi8994", "qcom,spmi-pmic"; > + reg = <0x2 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmi8994_gpios: gpio@c000 { > + compatible = "qcom,pmi8994-gpio", "qcom,spmi-gpio"; > + reg = <0xc000>; > + gpio-controller; > + gpio-ranges = <&pmi8994_gpios 0 0 10>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + pmi8994_mpps: mpps@a000 { > + compatible = "qcom,pmi8994-mpp", "qcom,spmi-mpp"; > + reg = <0xa000>; > + gpio-controller; > + gpio-ranges = <&pmi8994_mpps 0 0 4>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > + pmic@3 { > + compatible = "qcom,pmi8994", "qcom,spmi-pmic"; > + reg = <0x3 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmi8994_lpg: pwm { > + compatible = "qcom,pmi8994-lpg"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + #pwm-cells = <2>; > + > + status = "disabled"; > + }; > + > + pmi8994_spmi_regulators: regulators { > + compatible = "qcom,pmi8994-regulators"; > + }; > + > + pmi8994_wled: wled@d800 { > + compatible = "qcom,pmi8994-wled"; > + reg = <0xd800>, <0xd900>; > + interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, > + <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; > + interrupt-names = "ovp", "short"; > + qcom,cabc; > + qcom,external-pfet; > + status = "disabled"; > + }; > + }; > +}; > > -- > 2.43.1 >
diff --git a/arch/arm/dts/pm8994.dtsi b/arch/arm/dts/pm8994.dtsi new file mode 100644 index 000000000000..d44a95caf04a --- /dev/null +++ b/arch/arm/dts/pm8994.dtsi @@ -0,0 +1,152 @@ +// SPDX-License-Identifier: GPL-2.0 +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +/ { + thermal-zones { + pm8994-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&pm8994_temp>; + + trips { + pm8994_alert0: pm8994-alert0 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + pm8994_crit: pm8994-crit { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; +}; + +&spmi_bus { + + pmic@0 { + compatible = "qcom,pm8994", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>, <0x6100>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; + }; + + pm8994_pon: pon@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x800>; + mode-bootloader = <0x2>; + mode-recovery = <0x1>; + + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + }; + + pm8994_resin: resin { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + status = "disabled"; + }; + }; + + pm8994_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; + io-channels = <&pm8994_vadc VADC_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pm8994_vadc: adc@3100 { + compatible = "qcom,spmi-vadc"; + reg = <0x3100>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + channel@7 { + reg = <VADC_VSYS>; + qcom,pre-scaling = <1 3>; + label = "vph_pwr"; + }; + channel@8 { + reg = <VADC_DIE_TEMP>; + label = "die_temp"; + }; + channel@9 { + reg = <VADC_REF_625MV>; + label = "ref_625mv"; + }; + channel@a { + reg = <VADC_REF_1250MV>; + label = "ref_1250mv"; + }; + channel@e { + reg = <VADC_GND_REF>; + }; + channel@f { + reg = <VADC_VDD_VADC>; + }; + }; + + pm8994_gpios: gpio@c000 { + compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio"; + reg = <0xc000>; + gpio-controller; + gpio-ranges = <&pm8994_gpios 0 0 22>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pm8994_mpps: mpps@a000 { + compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp"; + reg = <0xa000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pm8994_mpps 0 0 8>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@1 { + compatible = "qcom,pm8994", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8994_lpg: pwm { + compatible = "qcom,pm8994-lpg"; + + #address-cells = <1>; + #size-cells = <0>; + #pwm-cells = <2>; + + status = "disabled"; + }; + + pm8994_spmi_regulators: regulators { + compatible = "qcom,pm8994-regulators"; + }; + }; +}; diff --git a/arch/arm/dts/pmi8994.dtsi b/arch/arm/dts/pmi8994.dtsi new file mode 100644 index 000000000000..36d6a1fb553a --- /dev/null +++ b/arch/arm/dts/pmi8994.dtsi @@ -0,0 +1,65 @@ +// SPDX-License-Identifier: GPL-2.0 +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + + pmic@2 { + compatible = "qcom,pmi8994", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmi8994_gpios: gpio@c000 { + compatible = "qcom,pmi8994-gpio", "qcom,spmi-gpio"; + reg = <0xc000>; + gpio-controller; + gpio-ranges = <&pmi8994_gpios 0 0 10>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pmi8994_mpps: mpps@a000 { + compatible = "qcom,pmi8994-mpp", "qcom,spmi-mpp"; + reg = <0xa000>; + gpio-controller; + gpio-ranges = <&pmi8994_mpps 0 0 4>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@3 { + compatible = "qcom,pmi8994", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmi8994_lpg: pwm { + compatible = "qcom,pmi8994-lpg"; + + #address-cells = <1>; + #size-cells = <0>; + #pwm-cells = <2>; + + status = "disabled"; + }; + + pmi8994_spmi_regulators: regulators { + compatible = "qcom,pmi8994-regulators"; + }; + + pmi8994_wled: wled@d800 { + compatible = "qcom,pmi8994-wled"; + reg = <0xd800>, <0xd900>; + interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, + <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "ovp", "short"; + qcom,cabc; + qcom,external-pfet; + status = "disabled"; + }; + }; +};