diff mbox series

[V9,3/3] tty: serial: uartps: Add rs485 support to uartps driver

Message ID 20240118074003.2334348-4-manikanta.guntupalli@amd.com
State Superseded
Headers show
Series Add rs485 support to uartps driver | expand

Commit Message

Manikanta Guntupalli Jan. 18, 2024, 7:40 a.m. UTC
Add rs485 support to uartps driver. Use either rts-gpios or RTS
to control RS485 phy as driver or a receiver.

Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
---
Changes for V2:
Modify optional gpio name to xlnx,phy-ctrl-gpios.
Update commit description.
Add support for RTS, delay_rts_before_send and delay_rts_after_send in RS485 mode.

Changes for V3:
Modify optional gpio name to rts-gpios.
Update commit description.
Move cdns_uart_tx_empty function to avoid prototype statement.
Remove assignment of struct serial_rs485 to port->rs485 as
serial core performs that.
Switch to native RTS in non GPIO case.
Handle rs485 during stop tx.
Remove explicit calls to configure gpio direction and value,
as devm_gpiod_get_optional performs that by using GPIOD_OUT_LOW argument.
Update implementation to support configuration of GPIO/RTS value
based on user configuration of SER_RS485_RTS_ON_SEND and
SER_RS485_RTS_AFTER_SEND. Move implementation to start_tx from handle_tx.

Changes for V4:
Create separate patch for cdns_uart_tx_empty relocation.
Call cdns_rs485_rx_setup() before uart_add_one_port() in probe.
Update gpio descriptor name to gpiod_rts.
Instead of cdns_rs485_config_gpio_rts_high() and
cdns_rs485_config_gpio_rts_low() functions for RTS/GPIO value
configuration implement cdns_rts_gpio_enable().
Disable auto rts and call cdns_uart_stop_tx() from cdns_rs485_config.
Use timer instead of mdelay for delay_rts_before_send and delay_rts_after_send.
Update cdns_uart_set_mctrl to support GPIO/RTS.

Changes for V5:
None.

Changes for V6:
Disable the TX and RX in cdns_rs485_config() when rs485 disabled.
Hold lock for cdns_uart_handle_tx() in cdns_rs485_tx_callback().

Changes for V7:
None.

Changes for V8:
Use hrtimer instead of timer list.
Simplify cdns_rs485_tx_setup() and cdns_rs485_rx_setup().
Update argument of cdns_rts_gpio_enable() in cdns_uart_set_mctrl().
Add cdns_calc_after_tx_delay() to calculate required delay after tx.
Add hrtimer setup in cdns_rs485_config().
Move enable TX Empty interrupt and rs485 rx callback scheduling part to
cdns_uart_handle_tx().

Changes for V9:
Remove stop tx timer.
Remove hrtimer_cancel() call from cdns_uart_start_tx().
Handle gpio case separately in cdns_uart_set_mctrl().
Move hrtimer_cancel() call from below to above in cdns_uart_shutdown().
---
 drivers/tty/serial/xilinx_uartps.c | 200 ++++++++++++++++++++++++++++-
 1 file changed, 196 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 787c7cbc6600..c44c77b3e54f 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -22,7 +22,9 @@ 
 #include <linux/of.h>
 #include <linux/module.h>
 #include <linux/pm_runtime.h>
-#include <linux/iopoll.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
 
 #define CDNS_UART_TTY_NAME	"ttyPS"
 #define CDNS_UART_NAME		"xuartps"
@@ -193,6 +195,9 @@  MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
  * @clk_rate_change_nb:	Notifier block for clock changes
  * @quirks:		Flags for RXBS support.
  * @cts_override:	Modem control state override
+ * @gpiod_rts:		Pointer to the gpio descriptor
+ * @rs485_tx_started:	RS485 tx state
+ * @tx_timer:		Timer for tx
  */
 struct cdns_uart {
 	struct uart_port	*port;
@@ -203,10 +208,21 @@  struct cdns_uart {
 	struct notifier_block	clk_rate_change_nb;
 	u32			quirks;
 	bool cts_override;
+	struct gpio_desc	*gpiod_rts;
+	bool			rs485_tx_started;
+	struct hrtimer		tx_timer;
 };
 struct cdns_platform_data {
 	u32 quirks;
 };
+
+struct serial_rs485 cdns_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+		 SER_RS485_RTS_AFTER_SEND,
+	.delay_rts_before_send = 1,
+	.delay_rts_after_send = 1,
+};
+
 #define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
 		clk_rate_change_nb)
 
@@ -305,6 +321,55 @@  static void cdns_uart_handle_rx(void *dev_id, unsigned int isrstatus)
 	tty_flip_buffer_push(&port->state->port);
 }
 
+/**
+ * cdns_rts_gpio_enable - Configure RTS/GPIO to high/low
+ * @cdns_uart: Handle to the cdns_uart
+ * @enable: Value to be set to RTS/GPIO
+ */
+static void cdns_rts_gpio_enable(struct cdns_uart *cdns_uart, bool enable)
+{
+	u32 val;
+
+	if (cdns_uart->gpiod_rts) {
+		gpiod_set_value(cdns_uart->gpiod_rts, enable);
+	} else {
+		val = readl(cdns_uart->port->membase + CDNS_UART_MODEMCR);
+		if (enable)
+			val |= CDNS_UART_MODEMCR_RTS;
+		else
+			val &= ~CDNS_UART_MODEMCR_RTS;
+		writel(val, cdns_uart->port->membase + CDNS_UART_MODEMCR);
+	}
+}
+
+/**
+ * cdns_rs485_tx_setup - Tx setup specific to rs485
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static void cdns_rs485_tx_setup(struct cdns_uart *cdns_uart)
+{
+	bool enable;
+
+	enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_ON_SEND;
+	cdns_rts_gpio_enable(cdns_uart, enable);
+
+	cdns_uart->rs485_tx_started = true;
+}
+
+/**
+ * cdns_rs485_rx_setup - Rx setup specific to rs485
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static void cdns_rs485_rx_setup(struct cdns_uart *cdns_uart)
+{
+	bool enable;
+
+	enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_AFTER_SEND;
+	cdns_rts_gpio_enable(cdns_uart, enable);
+
+	cdns_uart->rs485_tx_started = false;
+}
+
 /**
  * cdns_uart_tx_empty -  Check whether TX is empty
  * @port: Handle to the uart port structure
@@ -320,6 +385,37 @@  static unsigned int cdns_uart_tx_empty(struct uart_port *port)
 	return (status == CDNS_UART_SR_TXEMPTY) ? TIOCSER_TEMT : 0;
 }
 
+/**
+ * cdns_rs485_rx_callback - Timer rx callback handler for rs485.
+ * @t: Handle to the hrtimer structure
+ */
+static enum hrtimer_restart cdns_rs485_rx_callback(struct hrtimer *t)
+{
+	struct cdns_uart *cdns_uart = container_of(t, struct cdns_uart, tx_timer);
+
+	/*
+	 * Default Rx should be setup, because Rx signaling path
+	 * need to enable to receive data.
+	 */
+	cdns_rs485_rx_setup(cdns_uart);
+
+	return HRTIMER_NORESTART;
+}
+
+/**
+ * cdns_calc_after_tx_delay - calculate delay required for after tx.
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static u64 cdns_calc_after_tx_delay(struct cdns_uart *cdns_uart)
+{
+	/*
+	 * Frame time + stop bit time + rs485.delay_rts_after_send
+	 */
+	return cdns_uart->port->frame_time
+	       + DIV_ROUND_UP(cdns_uart->port->frame_time, 7)
+	       + (u64)cdns_uart->port->rs485.delay_rts_after_send * NSEC_PER_MSEC;
+}
+
 /**
  * cdns_uart_handle_tx - Handle the bytes to be transmitted.
  * @dev_id: Id of the UART port
@@ -328,6 +424,7 @@  static unsigned int cdns_uart_tx_empty(struct uart_port *port)
 static void cdns_uart_handle_tx(void *dev_id)
 {
 	struct uart_port *port = (struct uart_port *)dev_id;
+	struct cdns_uart *cdns_uart = port->private_data;
 	struct circ_buf *xmit = &port->state->xmit;
 	unsigned int numbytes;
 
@@ -347,6 +444,16 @@  static void cdns_uart_handle_tx(void *dev_id)
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(port);
+
+	/* Enable the TX Empty interrupt */
+	writel(CDNS_UART_IXR_TXEMPTY, cdns_uart->port->membase + CDNS_UART_IER);
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED &&
+	    (uart_circ_empty(xmit) || uart_tx_stopped(port))) {
+		cdns_uart->tx_timer.function = &cdns_rs485_rx_callback;
+		hrtimer_start(&cdns_uart->tx_timer,
+			      ns_to_ktime(cdns_calc_after_tx_delay(cdns_uart)), HRTIMER_MODE_REL);
+	}
 }
 
 /**
@@ -579,6 +686,21 @@  static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
 }
 #endif
 
+/**
+ * cdns_rs485_tx_callback - Timer tx callback handler for rs485.
+ * @t: Handle to the hrtimer structure
+ */
+static enum hrtimer_restart cdns_rs485_tx_callback(struct hrtimer *t)
+{
+	struct cdns_uart *cdns_uart = container_of(t, struct cdns_uart, tx_timer);
+
+	uart_port_lock(cdns_uart->port);
+	cdns_uart_handle_tx(cdns_uart->port);
+	uart_port_unlock(cdns_uart->port);
+
+	return HRTIMER_NORESTART;
+}
+
 /**
  * cdns_uart_start_tx -  Start transmitting bytes
  * @port: Handle to the uart port structure
@@ -586,6 +708,7 @@  static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
 static void cdns_uart_start_tx(struct uart_port *port)
 {
 	unsigned int status;
+	struct cdns_uart *cdns_uart = port->private_data;
 
 	if (uart_tx_stopped(port))
 		return;
@@ -605,10 +728,16 @@  static void cdns_uart_start_tx(struct uart_port *port)
 	/* Clear the TX Empty interrupt */
 	writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR);
 
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED) {
+		if (!cdns_uart->rs485_tx_started) {
+			cdns_uart->tx_timer.function = &cdns_rs485_tx_callback;
+			cdns_rs485_tx_setup(cdns_uart);
+			return hrtimer_start(&cdns_uart->tx_timer,
+					     ms_to_ktime(port->rs485.delay_rts_before_send),
+					     HRTIMER_MODE_REL);
+		}
+	}
 	cdns_uart_handle_tx(port);
-
-	/* Enable the TX Empty interrupt */
-	writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER);
 }
 
 /**
@@ -618,6 +747,10 @@  static void cdns_uart_start_tx(struct uart_port *port)
 static void cdns_uart_stop_tx(struct uart_port *port)
 {
 	unsigned int regval;
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
+		cdns_rs485_rx_setup(cdns_uart);
 
 	regval = readl(port->membase + CDNS_UART_CR);
 	regval |= CDNS_UART_CR_TX_DIS;
@@ -830,6 +963,9 @@  static int cdns_uart_startup(struct uart_port *port)
 		(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
 		cpu_relax();
 
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
+		cdns_rs485_rx_setup(cdns_uart);
+
 	/*
 	 * Clear the RX disable bit and then set the RX enable bit to enable
 	 * the receiver.
@@ -889,6 +1025,10 @@  static void cdns_uart_shutdown(struct uart_port *port)
 {
 	int status;
 	unsigned long flags;
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
+		hrtimer_cancel(&cdns_uart->tx_timer);
 
 	uart_port_lock_irqsave(port, &flags);
 
@@ -1034,6 +1174,8 @@  static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 
 	if (mctrl & TIOCM_RTS)
 		val |= CDNS_UART_MODEMCR_RTS;
+	if (cdns_uart_data->gpiod_rts)
+		gpiod_set_value(cdns_uart_data->gpiod_rts, !(mctrl & TIOCM_RTS));
 	if (mctrl & TIOCM_DTR)
 		val |= CDNS_UART_MODEMCR_DTR;
 	if (mctrl & TIOCM_LOOP)
@@ -1456,6 +1598,39 @@  MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
 /* Temporary variable for storing number of instances */
 static int instances;
 
+/**
+ * cdns_rs485_config - Called when an application calls TIOCSRS485 ioctl.
+ * @port: Pointer to the uart_port structure
+ * @termios: Pointer to the ktermios structure
+ * @rs485: Pointer to the serial_rs485 structure
+ *
+ * Return: 0
+ */
+static int cdns_rs485_config(struct uart_port *port, struct ktermios *termios,
+			     struct serial_rs485 *rs485)
+{
+	u32 val;
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		dev_dbg(port->dev, "Setting UART to RS485\n");
+		/* Make sure auto RTS is disabled */
+		val = readl(port->membase + CDNS_UART_MODEMCR);
+		val &= ~CDNS_UART_MODEMCR_FCM;
+		writel(val, port->membase + CDNS_UART_MODEMCR);
+
+		/* Timer setup */
+		hrtimer_init(&cdns_uart->tx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+		cdns_uart->tx_timer.function = &cdns_rs485_tx_callback;
+
+		/* Disable transmitter and make Rx setup*/
+		cdns_uart_stop_tx(port);
+	} else {
+		hrtimer_cancel(&cdns_uart->tx_timer);
+	}
+	return 0;
+}
+
 /**
  * cdns_uart_probe - Platform driver probe
  * @pdev: Pointer to the platform device structure
@@ -1598,9 +1773,23 @@  static int cdns_uart_probe(struct platform_device *pdev)
 	port->private_data = cdns_uart_data;
 	port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
 			CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
+	port->rs485_config = cdns_rs485_config;
+	port->rs485_supported = cdns_rs485_supported;
 	cdns_uart_data->port = port;
 	platform_set_drvdata(pdev, port);
 
+	rc = uart_get_rs485_mode(port);
+	if (rc)
+		goto err_out_clk_notifier;
+
+	cdns_uart_data->gpiod_rts = devm_gpiod_get_optional(&pdev->dev, "rts",
+							    GPIOD_OUT_LOW);
+	if (IS_ERR(cdns_uart_data->gpiod_rts)) {
+		rc = PTR_ERR(cdns_uart_data->gpiod_rts);
+		dev_err(port->dev, "xuartps: devm_gpiod_get_optional failed\n");
+		goto err_out_clk_notifier;
+	}
+
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
 	pm_runtime_set_active(&pdev->dev);
@@ -1619,6 +1808,8 @@  static int cdns_uart_probe(struct platform_device *pdev)
 		console_port = port;
 	}
 #endif
+	if (cdns_uart_data->port->rs485.flags & SER_RS485_ENABLED)
+		cdns_rs485_rx_setup(cdns_uart_data);
 
 	rc = uart_add_one_port(&cdns_uart_uart_driver, port);
 	if (rc) {
@@ -1647,6 +1838,7 @@  static int cdns_uart_probe(struct platform_device *pdev)
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_dont_use_autosuspend(&pdev->dev);
+err_out_clk_notifier:
 #ifdef CONFIG_COMMON_CLK
 	clk_notifier_unregister(cdns_uart_data->uartclk,
 			&cdns_uart_data->clk_rate_change_nb);