@@ -1483,6 +1483,13 @@ static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
return omap_up_info;
}
+static const struct serial_rs485 serial_omap_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
+ SER_RS485_RX_DURING_TX,
+ .delay_rts_before_send = 1,
+ .delay_rts_after_send = 1,
+};
+
static int serial_omap_probe_rs485(struct uart_omap_port *up,
struct device *dev)
{
@@ -1497,6 +1504,9 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
if (!np)
return 0;
+ up->port.rs485_config = serial_omap_config_rs485;
+ up->port.rs485_supported = serial_omap_rs485_supported;
+
ret = uart_get_rs485_mode(&up->port);
if (ret)
return ret;
@@ -1531,13 +1541,6 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
return 0;
}
-static const struct serial_rs485 serial_omap_rs485_supported = {
- .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
- SER_RS485_RX_DURING_TX,
- .delay_rts_before_send = 1,
- .delay_rts_after_send = 1,
-};
-
static int serial_omap_probe(struct platform_device *pdev)
{
struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev);
@@ -1604,17 +1607,11 @@ static int serial_omap_probe(struct platform_device *pdev)
dev_info(up->port.dev, "no wakeirq for uart%d\n",
up->port.line);
- ret = serial_omap_probe_rs485(up, &pdev->dev);
- if (ret < 0)
- goto err_rs485;
-
sprintf(up->name, "OMAP UART%d", up->port.line);
up->port.mapbase = mem->start;
up->port.membase = base;
up->port.flags = omap_up_info->flags;
up->port.uartclk = omap_up_info->uartclk;
- up->port.rs485_config = serial_omap_config_rs485;
- up->port.rs485_supported = serial_omap_rs485_supported;
if (!up->port.uartclk) {
up->port.uartclk = DEFAULT_CLK_SPEED;
dev_warn(&pdev->dev,
@@ -1622,6 +1619,10 @@ static int serial_omap_probe(struct platform_device *pdev)
DEFAULT_CLK_SPEED);
}
+ ret = serial_omap_probe_rs485(up, &pdev->dev);
+ if (ret < 0)
+ goto err_rs485;
+
up->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
up->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
cpu_latency_qos_add_request(&up->pm_qos_request, up->latency);
The drivers RS485 support is deactivated if there is no RTS GPIO available. This is done by nullifying the ports rs485_supported struct. After that however the settings in serial_omap_rs485_supported are assigned to the same structure unconditionally, which results in an unintended reactivation of RS485 support. Fix this by moving the assignment to the beginning of serial_omap_probe_rs485() and thus before the check for the RTS GPIO. Also relocate the assignment of serial_omap_config_rs485() to have the complete RS485 setup in one function. Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified") Cc: stable@vger.kernel.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> --- drivers/tty/serial/omap-serial.c | 27 ++++++++++++++------------- 1 file changed, 14 insertions(+), 13 deletions(-)