| Message ID | 20240103132852.298964-2-emil.renner.berthing@canonical.com |
|---|---|
| State | New |
| Headers | show |
| Series | [v2,1/8] dt-bindings: pinctrl: Add thead,th1520-pinctrl bindings | expand |
On Wed, Jan 03, 2024 at 02:28:38PM +0100, Emil Renner Berthing wrote: > Add bindings for the pin controllers on the T-Head TH1520 RISC-V SoC. > > Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> > --- > .../pinctrl/thead,th1520-pinctrl.yaml | 372 ++++++++++++++++++ > 1 file changed, 372 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml > > diff --git a/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml > new file mode 100644 > index 000000000000..d3ad7a7cfdd1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml > @@ -0,0 +1,372 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pinctrl/thead,th1520-pinctrl.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: T-Head TH1520 SoC pin controller > + > +maintainers: > + - Emil Renner Berthing <emil.renner.berthing@canonical.com> > + > +description: | > + Pinmux and pinconf controller in the T-Head TH1520 RISC-V SoC. > + > + The TH1520 has 3 groups of pads each controlled from different memory ranges. > + Confusingly the memory ranges are named > + PADCTRL_AOSYS -> PAD Group 1 > + PADCTRL1_APSYS -> PAD Group 2 > + PADCTRL0_APSYS -> PAD Group 3 > + > + Each pad can be muxed individually to up to 6 different functions. For most > + pads only a few of those 6 configurations are valid though, and a few pads in > + group 1 does not support muxing at all. > + > + Pinconf is fairly regular except for a few pads in group 1 that either can't > + be configured or has some special functions. The rest have configurable drive > + strength, input enable, schmitt trigger, slew rate, pull-up and pull-down in > + addition to a special strong pull up. > + > + Certain pads in group 1 can be muxed to AUDIO_PA0 - AUDIO_PA30 functions and > + are then meant to be used by the audio co-processor. Each such pad can then > + be further muxed to either audio GPIO or one of 4 functions such as UART, I2C > + and I2S. If the audio pad is muxed to one of the 4 functions then pinconf is > + also configured in different registers. All of this is done from a different > + AUDIO_IOCTRL memory range and is left to the audio co-processor for now. It is still not clear to me if each instance is a different programming model or the same with just different connections. The latter should be the same compatible string. That needs to be answered in *this* patch, not a reply. > + > +properties: > + compatible: > + enum: > + - thead,th1520-group1-pinctrl > + - thead,th1520-group2-pinctrl > + - thead,th1520-group3-pinctrl > + > + reg: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > +patternProperties: > + '-[0-9]+$': > + type: object > + > + additionalProperties: false > + > + patternProperties: > + '-pins$': > + type: object > + $ref: /schemas/pinctrl/pincfg-node.yaml > + > + additionalProperties: false > + > + description: > + A pinctrl node should contain at least one subnode describing one > + or more pads and their associated pinmux and pinconf settings. > + > + properties: > + pins: > + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pins > + description: List of pads that properties in the node apply to. > + > + function: > + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/function > + enum: [ gpio, pwm, uart, ir, i2c, spi, qspi, sdio, audio, i2s, > + gmac0, gmac1, dpu0, dpu1, isp, hdmi, bootsel, debug, > + clock, jtag, iso7816, efuse, reset ] > + description: The mux function to select for the given pins. > + > + bias-disable: true > + > + bias-pull-up: > + oneOf: > + - type: boolean > + description: Enable the regular 48kOhm pull-up > + - enum: [ 2100, 48000 ] > + description: Enable the strong 2.1kOhm pull-up or regular 48kOhm pull-up > + > + bias-pull-down: > + oneOf: > + - type: boolean > + - const: 44000 > + description: Enable the regular 44kOhm pull-down > + > + drive-strength: > + enum: [ 1, 2, 3, 5, 7, 8, 10, 12, 13, 15, 16, 18, 20, 21, 23, 25 ] > + description: Drive strength in mA > + > + input-enable: true > + > + input-disable: true > + > + input-schmitt-enable: true > + > + input-schmitt-disable: true > + > + slew-rate: > + maximum: 1 > + > + required: > + - pins > + > +required: > + - compatible > + - reg > + - clocks > + > +additionalProperties: false > + > +allOf: > + - $ref: pinctrl.yaml# > + - if: > + properties: > + compatible: > + const: thead,th1520-group1-pinctrl > + then: > + patternProperties: > + '-[0-9]+$': > + patternProperties: > + '-pins$': > + properties: > + pins: > + items: > + enum: > + - OSC_CLK_IN > + - OSC_CLK_OUT > + - SYS_RST_N > + - RTC_CLK_IN > + - RTC_CLK_OUT > + - TEST_MODE > + - DEBUG_MODE > + - POR_SEL > + - I2C_AON_SCL > + - I2C_AON_SDA > + - CPU_JTG_TCLK > + - CPU_JTG_TMS > + - CPU_JTG_TDI > + - CPU_JTG_TDO > + - CPU_JTG_TRST > + - AOGPIO_7 > + - AOGPIO_8 > + - AOGPIO_9 > + - AOGPIO_10 > + - AOGPIO_11 > + - AOGPIO_12 > + - AOGPIO_13 > + - AOGPIO_14 > + - AOGPIO_15 > + - AUDIO_PA0 > + - AUDIO_PA1 > + - AUDIO_PA2 > + - AUDIO_PA3 > + - AUDIO_PA4 > + - AUDIO_PA5 > + - AUDIO_PA6 > + - AUDIO_PA7 > + - AUDIO_PA8 > + - AUDIO_PA9 > + - AUDIO_PA10 > + - AUDIO_PA11 > + - AUDIO_PA12 > + - AUDIO_PA13 > + - AUDIO_PA14 > + - AUDIO_PA15 > + - AUDIO_PA16 > + - AUDIO_PA17 > + - AUDIO_PA27 > + - AUDIO_PA28 > + - AUDIO_PA29 > + - AUDIO_PA30 > + - if: > + properties: > + compatible: > + const: thead,th1520-group2-pinctrl > + then: > + patternProperties: > + '-[0-9]+$': > + patternProperties: > + '-pins$': > + properties: > + pins: > + items: > + enum: > + - QSPI1_SCLK > + - QSPI1_CSN0 > + - QSPI1_D0_MOSI > + - QSPI1_D1_MISO > + - QSPI1_D2_WP > + - QSPI1_D3_HOLD > + - I2C0_SCL > + - I2C0_SDA > + - I2C1_SCL > + - I2C1_SDA > + - UART1_TXD > + - UART1_RXD > + - UART4_TXD > + - UART4_RXD > + - UART4_CTSN > + - UART4_RTSN > + - UART3_TXD > + - UART3_RXD > + - GPIO0_18 > + - GPIO0_19 > + - GPIO0_20 > + - GPIO0_21 > + - GPIO0_22 > + - GPIO0_23 > + - GPIO0_24 > + - GPIO0_25 > + - GPIO0_26 > + - GPIO0_27 > + - GPIO0_28 > + - GPIO0_29 > + - GPIO0_30 > + - GPIO0_31 > + - GPIO1_0 > + - GPIO1_1 > + - GPIO1_2 > + - GPIO1_3 > + - GPIO1_4 > + - GPIO1_5 > + - GPIO1_6 > + - GPIO1_7 > + - GPIO1_8 > + - GPIO1_9 > + - GPIO1_10 > + - GPIO1_11 > + - GPIO1_12 > + - GPIO1_13 > + - GPIO1_14 > + - GPIO1_15 > + - GPIO1_16 > + - CLK_OUT_0 > + - CLK_OUT_1 > + - CLK_OUT_2 > + - CLK_OUT_3 > + - GPIO1_21 > + - GPIO1_22 > + - GPIO1_23 > + - GPIO1_24 > + - GPIO1_25 > + - GPIO1_26 > + - GPIO1_27 > + - GPIO1_28 > + - GPIO1_29 > + - GPIO1_30 > + - if: > + properties: > + compatible: > + const: thead,th1520-group3-pinctrl > + then: > + patternProperties: > + '-[0-9]+$': > + patternProperties: > + '-pins$': > + properties: > + pins: > + items: > + enum: > + - UART0_TXD > + - UART0_RXD > + - QSPI0_SCLK > + - QSPI0_CSN0 > + - QSPI0_CSN1 > + - QSPI0_D0_MOSI > + - QSPI0_D1_MISO > + - QSPI0_D2_WP > + - QSPI1_D3_HOLD > + - I2C2_SCL > + - I2C2_SDA > + - I2C3_SCL > + - I2C3_SDA > + - GPIO2_13 > + - SPI_SCLK > + - SPI_CSN > + - SPI_MOSI > + - SPI_MISO > + - GPIO2_18 > + - GPIO2_19 > + - GPIO2_20 > + - GPIO2_21 > + - GPIO2_22 > + - GPIO2_23 > + - GPIO2_24 > + - GPIO2_25 > + - SDIO0_WPRTN > + - SDIO0_DETN > + - SDIO1_WPRTN > + - SDIO1_DETN > + - GPIO2_30 > + - GPIO2_31 > + - GPIO3_0 > + - GPIO3_1 > + - GPIO3_2 > + - GPIO3_3 > + - HDMI_SCL > + - HDMI_SDA > + - HDMI_CEC > + - GMAC0_TX_CLK > + - GMAC0_RX_CLK > + - GMAC0_TXEN > + - GMAC0_TXD0 > + - GMAC0_TXD1 > + - GMAC0_TXD2 > + - GMAC0_TXD3 > + - GMAC0_RXDV > + - GMAC0_RXD0 > + - GMAC0_RXD1 > + - GMAC0_RXD2 > + - GMAC0_RXD3 > + - GMAC0_MDC > + - GMAC0_MDIO > + - GMAC0_COL > + - GMAC0_CRS > + > +examples: > + - | > + padctrl0_apsys: pinctrl@ec007000 { > + compatible = "thead,th1520-group3-pinctrl"; > + reg = <0xec007000 0x1000>; > + clocks = <&apb_clk>; > + > + uart0_pins: uart0-0 { > + tx-pins { > + pins = "UART0_TXD"; > + function = "uart"; > + bias-disable; > + drive-strength = <3>; > + input-disable; > + input-schmitt-disable; > + slew-rate = <0>; > + }; > + > + rx-pins { > + pins = "UART0_RXD"; > + function = "uart"; > + bias-disable; > + drive-strength = <1>; > + input-enable; > + input-schmitt-enable; > + slew-rate = <0>; > + }; > + }; > + }; > + > + padctrl1_apsys: pinctrl@e7f3c000 { > + compatible = "thead,th1520-group2-pinctrl"; > + reg = <0xe7f3c000 0x1000>; > + clocks = <&apb_clk>; > + > + i2c5_pins: i2c5-0 { > + i2c-pins { > + pins = "QSPI1_CSN0", /* I2C5_SCL */ > + "QSPI1_D0_MOSI"; /* I2C5_SDA */ > + function = "i2c"; > + bias-pull-up = <2100>; > + drive-strength = <7>; > + input-enable; > + input-schmitt-enable; > + slew-rate = <0>; > + }; > + }; > + }; > -- > 2.43.0 >
diff --git a/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml new file mode 100644 index 000000000000..d3ad7a7cfdd1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml @@ -0,0 +1,372 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/thead,th1520-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: T-Head TH1520 SoC pin controller + +maintainers: + - Emil Renner Berthing <emil.renner.berthing@canonical.com> + +description: | + Pinmux and pinconf controller in the T-Head TH1520 RISC-V SoC. + + The TH1520 has 3 groups of pads each controlled from different memory ranges. + Confusingly the memory ranges are named + PADCTRL_AOSYS -> PAD Group 1 + PADCTRL1_APSYS -> PAD Group 2 + PADCTRL0_APSYS -> PAD Group 3 + + Each pad can be muxed individually to up to 6 different functions. For most + pads only a few of those 6 configurations are valid though, and a few pads in + group 1 does not support muxing at all. + + Pinconf is fairly regular except for a few pads in group 1 that either can't + be configured or has some special functions. The rest have configurable drive + strength, input enable, schmitt trigger, slew rate, pull-up and pull-down in + addition to a special strong pull up. + + Certain pads in group 1 can be muxed to AUDIO_PA0 - AUDIO_PA30 functions and + are then meant to be used by the audio co-processor. Each such pad can then + be further muxed to either audio GPIO or one of 4 functions such as UART, I2C + and I2S. If the audio pad is muxed to one of the 4 functions then pinconf is + also configured in different registers. All of this is done from a different + AUDIO_IOCTRL memory range and is left to the audio co-processor for now. + +properties: + compatible: + enum: + - thead,th1520-group1-pinctrl + - thead,th1520-group2-pinctrl + - thead,th1520-group3-pinctrl + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + +patternProperties: + '-[0-9]+$': + type: object + + additionalProperties: false + + patternProperties: + '-pins$': + type: object + $ref: /schemas/pinctrl/pincfg-node.yaml + + additionalProperties: false + + description: + A pinctrl node should contain at least one subnode describing one + or more pads and their associated pinmux and pinconf settings. + + properties: + pins: + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pins + description: List of pads that properties in the node apply to. + + function: + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/function + enum: [ gpio, pwm, uart, ir, i2c, spi, qspi, sdio, audio, i2s, + gmac0, gmac1, dpu0, dpu1, isp, hdmi, bootsel, debug, + clock, jtag, iso7816, efuse, reset ] + description: The mux function to select for the given pins. + + bias-disable: true + + bias-pull-up: + oneOf: + - type: boolean + description: Enable the regular 48kOhm pull-up + - enum: [ 2100, 48000 ] + description: Enable the strong 2.1kOhm pull-up or regular 48kOhm pull-up + + bias-pull-down: + oneOf: + - type: boolean + - const: 44000 + description: Enable the regular 44kOhm pull-down + + drive-strength: + enum: [ 1, 2, 3, 5, 7, 8, 10, 12, 13, 15, 16, 18, 20, 21, 23, 25 ] + description: Drive strength in mA + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + slew-rate: + maximum: 1 + + required: + - pins + +required: + - compatible + - reg + - clocks + +additionalProperties: false + +allOf: + - $ref: pinctrl.yaml# + - if: + properties: + compatible: + const: thead,th1520-group1-pinctrl + then: + patternProperties: + '-[0-9]+$': + patternProperties: + '-pins$': + properties: + pins: + items: + enum: + - OSC_CLK_IN + - OSC_CLK_OUT + - SYS_RST_N + - RTC_CLK_IN + - RTC_CLK_OUT + - TEST_MODE + - DEBUG_MODE + - POR_SEL + - I2C_AON_SCL + - I2C_AON_SDA + - CPU_JTG_TCLK + - CPU_JTG_TMS + - CPU_JTG_TDI + - CPU_JTG_TDO + - CPU_JTG_TRST + - AOGPIO_7 + - AOGPIO_8 + - AOGPIO_9 + - AOGPIO_10 + - AOGPIO_11 + - AOGPIO_12 + - AOGPIO_13 + - AOGPIO_14 + - AOGPIO_15 + - AUDIO_PA0 + - AUDIO_PA1 + - AUDIO_PA2 + - AUDIO_PA3 + - AUDIO_PA4 + - AUDIO_PA5 + - AUDIO_PA6 + - AUDIO_PA7 + - AUDIO_PA8 + - AUDIO_PA9 + - AUDIO_PA10 + - AUDIO_PA11 + - AUDIO_PA12 + - AUDIO_PA13 + - AUDIO_PA14 + - AUDIO_PA15 + - AUDIO_PA16 + - AUDIO_PA17 + - AUDIO_PA27 + - AUDIO_PA28 + - AUDIO_PA29 + - AUDIO_PA30 + - if: + properties: + compatible: + const: thead,th1520-group2-pinctrl + then: + patternProperties: + '-[0-9]+$': + patternProperties: + '-pins$': + properties: + pins: + items: + enum: + - QSPI1_SCLK + - QSPI1_CSN0 + - QSPI1_D0_MOSI + - QSPI1_D1_MISO + - QSPI1_D2_WP + - QSPI1_D3_HOLD + - I2C0_SCL + - I2C0_SDA + - I2C1_SCL + - I2C1_SDA + - UART1_TXD + - UART1_RXD + - UART4_TXD + - UART4_RXD + - UART4_CTSN + - UART4_RTSN + - UART3_TXD + - UART3_RXD + - GPIO0_18 + - GPIO0_19 + - GPIO0_20 + - GPIO0_21 + - GPIO0_22 + - GPIO0_23 + - GPIO0_24 + - GPIO0_25 + - GPIO0_26 + - GPIO0_27 + - GPIO0_28 + - GPIO0_29 + - GPIO0_30 + - GPIO0_31 + - GPIO1_0 + - GPIO1_1 + - GPIO1_2 + - GPIO1_3 + - GPIO1_4 + - GPIO1_5 + - GPIO1_6 + - GPIO1_7 + - GPIO1_8 + - GPIO1_9 + - GPIO1_10 + - GPIO1_11 + - GPIO1_12 + - GPIO1_13 + - GPIO1_14 + - GPIO1_15 + - GPIO1_16 + - CLK_OUT_0 + - CLK_OUT_1 + - CLK_OUT_2 + - CLK_OUT_3 + - GPIO1_21 + - GPIO1_22 + - GPIO1_23 + - GPIO1_24 + - GPIO1_25 + - GPIO1_26 + - GPIO1_27 + - GPIO1_28 + - GPIO1_29 + - GPIO1_30 + - if: + properties: + compatible: + const: thead,th1520-group3-pinctrl + then: + patternProperties: + '-[0-9]+$': + patternProperties: + '-pins$': + properties: + pins: + items: + enum: + - UART0_TXD + - UART0_RXD + - QSPI0_SCLK + - QSPI0_CSN0 + - QSPI0_CSN1 + - QSPI0_D0_MOSI + - QSPI0_D1_MISO + - QSPI0_D2_WP + - QSPI1_D3_HOLD + - I2C2_SCL + - I2C2_SDA + - I2C3_SCL + - I2C3_SDA + - GPIO2_13 + - SPI_SCLK + - SPI_CSN + - SPI_MOSI + - SPI_MISO + - GPIO2_18 + - GPIO2_19 + - GPIO2_20 + - GPIO2_21 + - GPIO2_22 + - GPIO2_23 + - GPIO2_24 + - GPIO2_25 + - SDIO0_WPRTN + - SDIO0_DETN + - SDIO1_WPRTN + - SDIO1_DETN + - GPIO2_30 + - GPIO2_31 + - GPIO3_0 + - GPIO3_1 + - GPIO3_2 + - GPIO3_3 + - HDMI_SCL + - HDMI_SDA + - HDMI_CEC + - GMAC0_TX_CLK + - GMAC0_RX_CLK + - GMAC0_TXEN + - GMAC0_TXD0 + - GMAC0_TXD1 + - GMAC0_TXD2 + - GMAC0_TXD3 + - GMAC0_RXDV + - GMAC0_RXD0 + - GMAC0_RXD1 + - GMAC0_RXD2 + - GMAC0_RXD3 + - GMAC0_MDC + - GMAC0_MDIO + - GMAC0_COL + - GMAC0_CRS + +examples: + - | + padctrl0_apsys: pinctrl@ec007000 { + compatible = "thead,th1520-group3-pinctrl"; + reg = <0xec007000 0x1000>; + clocks = <&apb_clk>; + + uart0_pins: uart0-0 { + tx-pins { + pins = "UART0_TXD"; + function = "uart"; + bias-disable; + drive-strength = <3>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + + rx-pins { + pins = "UART0_RXD"; + function = "uart"; + bias-disable; + drive-strength = <1>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + }; + + padctrl1_apsys: pinctrl@e7f3c000 { + compatible = "thead,th1520-group2-pinctrl"; + reg = <0xe7f3c000 0x1000>; + clocks = <&apb_clk>; + + i2c5_pins: i2c5-0 { + i2c-pins { + pins = "QSPI1_CSN0", /* I2C5_SCL */ + "QSPI1_D0_MOSI"; /* I2C5_SDA */ + function = "i2c"; + bias-pull-up = <2100>; + drive-strength = <7>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + };
Add bindings for the pin controllers on the T-Head TH1520 RISC-V SoC. Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> --- .../pinctrl/thead,th1520-pinctrl.yaml | 372 ++++++++++++++++++ 1 file changed, 372 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml