diff mbox series

[v3,3/3] iio: adc: Add support for QCOM PMIC5 Gen3 ADC

Message ID 20231231171237.3322376-4-quic_jprakash@quicinc.com
State New
Headers show
Series iio: adc: Add support for QCOM SPMI PMIC5 Gen3 ADC | expand

Commit Message

Jishnu Prakash Dec. 31, 2023, 5:12 p.m. UTC
The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
with all SW communication to ADC going through PMK8550 which
communicates with other PMICs through PBS.

One major difference is that the register interface used here is that
of an SDAM (Shared Direct Access Memory) peripheral present on PMK8550.
There may be more than one SDAM used for ADC5 Gen3 and each has eight
channels, which may be used for either immediate reads (same functionality
as previous PMIC5 and PMIC5 Gen2 ADC peripherals) or recurring measurements
(same as ADC_TM functionality).

In this case, we have VADC and ADC_TM functionality combined into the
same driver. By convention, we reserve the first channel of the first
SDAM for all immediate reads and use the remaining channels across all
SDAMs for ADC_TM monitoring functionality.

Changes since v1:
- Removed datashet_name usage and implemented read_label() function
- In probe, updated channel property in iio_chan_spec from individual
  channel to virtual channel and set indexed property to 1, due to the
  above change.
- Updated order of checks in ISR
- Removed the driver remove callback and replaced with callbacks in a
  devm_add_action call in probe.
- Addressed other comments from reviewers.

Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
---
 drivers/iio/adc/Kconfig               |   25 +
 drivers/iio/adc/Makefile              |    1 +
 drivers/iio/adc/qcom-spmi-adc5-gen3.c | 1198 +++++++++++++++++++++++++
 3 files changed, 1224 insertions(+)
 create mode 100644 drivers/iio/adc/qcom-spmi-adc5-gen3.c

Comments

kernel test robot Dec. 31, 2023, 7:54 p.m. UTC | #1
Hi Jishnu,

kernel test robot noticed the following build warnings:

[auto build test WARNING on next-20231222]
[cannot apply to robh/for-next jic23-iio/togreg rafael-pm/thermal v6.7-rc7 v6.7-rc6 v6.7-rc5 linus/master v6.7-rc7]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Jishnu-Prakash/dt-bindings-iio-adc-Move-QCOM-ADC-bindings-to-iio-adc-folder/20240101-011705
base:   next-20231222
patch link:    https://lore.kernel.org/r/20231231171237.3322376-4-quic_jprakash%40quicinc.com
patch subject: [PATCH v3 3/3] iio: adc: Add support for QCOM PMIC5 Gen3 ADC
config: m68k-allyesconfig (https://download.01.org/0day-ci/archive/20240101/202401010303.pkYUJjby-lkp@intel.com/config)
compiler: m68k-linux-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240101/202401010303.pkYUJjby-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202401010303.pkYUJjby-lkp@intel.com/

All warnings (new ones prefixed by >>):

>> drivers/iio/adc/qcom-spmi-adc5-gen3.c:290: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
    * Worst case delay from PBS in readying handshake bit
   drivers/iio/adc/qcom-spmi-adc5-gen3.c:332: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
    * Worst case delay from PBS for conversion time can be


vim +290 drivers/iio/adc/qcom-spmi-adc5-gen3.c

   288	
   289	/**
 > 290	 * Worst case delay from PBS in readying handshake bit
   291	 * can be up to 15ms, when PBS is busy running other
   292	 * simultaneous transactions, while in the best case, it is
   293	 * already ready at this point. Assigning polling delay and
   294	 * retry count accordingly.
   295	 */
   296
Jonathan Cameron Jan. 1, 2024, 5:54 p.m. UTC | #2
On Sun, 31 Dec 2023 22:42:37 +0530
Jishnu Prakash <quic_jprakash@quicinc.com> wrote:

> The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
> with all SW communication to ADC going through PMK8550 which
> communicates with other PMICs through PBS.
> 
> One major difference is that the register interface used here is that
> of an SDAM (Shared Direct Access Memory) peripheral present on PMK8550.
> There may be more than one SDAM used for ADC5 Gen3 and each has eight
> channels, which may be used for either immediate reads (same functionality
> as previous PMIC5 and PMIC5 Gen2 ADC peripherals) or recurring measurements
> (same as ADC_TM functionality).
> 
> In this case, we have VADC and ADC_TM functionality combined into the
> same driver. By convention, we reserve the first channel of the first
> SDAM for all immediate reads and use the remaining channels across all
> SDAMs for ADC_TM monitoring functionality.
> 
> Changes since v1:

Move below the --- we don't want this in the eventual git commit as it
is just noise.

> - Removed datashet_name usage and implemented read_label() function
> - In probe, updated channel property in iio_chan_spec from individual
>   channel to virtual channel and set indexed property to 1, due to the
>   above change.
> - Updated order of checks in ISR
> - Removed the driver remove callback and replaced with callbacks in a
>   devm_add_action call in probe.
> - Addressed other comments from reviewers.
> 
> Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
> ---

A few quick comments inline because you already have a request for a substantial
change.  Main one is the devm handling tries to do too much with one callback and
I think introduces various bugs as a result.  Use the appropriate number of callbacks
so each action has it's own undo registered thus they will happen in the correct order
and no unnecessary ones will occur.

Jonathan


> diff --git a/drivers/iio/adc/qcom-spmi-adc5-gen3.c b/drivers/iio/adc/qcom-spmi-adc5-gen3.c
> new file mode 100644
> index 000000000000..5b5848492245
> --- /dev/null
> +++ b/drivers/iio/adc/qcom-spmi-adc5-gen3.c
> @@ -0,0 +1,1198 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include <asm/unaligned.h>

Whilst it isn't alphabetical order, general convention is
to put asm includes in a block after linux ones.

> +#include <linux/bitfield.h>
> +#include <linux/bitops.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/adc/qcom-vadc-common.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/log2.h>
> +#include <linux/math64.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/thermal.h>
> +
> +#include <dt-bindings/iio/adc/qcom,spmi-vadc.h>

> +
> +/**
> + * Worst case delay from PBS for conversion time can be
> + * up to 500ms, when PBS has timed out twice, once for
> + * the initial attempt and once for a retry of the same
> + * transaction.
> + */
> +
> +#define ADC5_GEN3_CONV_TIMEOUT_MS	501
> +
> +static int adc5_gen3_do_conversion(struct adc5_chip *adc,
> +			struct adc5_channel_prop *prop,
> +			u16 *data_volt)
> +{
> +	u8 val, sdam_index = prop->sdam_index;
> +	unsigned long rc;
> +	int ret;
> +
> +	/* Reserve channel 0 of first SDAM for immediate conversions */
> +	if (prop->adc_tm)
> +		sdam_index = 0;
> +
> +	mutex_lock(&adc->lock);
> +	ret = adc5_gen3_poll_wait_hs(adc, 0);
> +	if (ret)
> +		goto unlock;
> +
> +	ret = adc5_gen3_configure(adc, prop);
> +	if (ret) {
> +		dev_err(adc->dev, "ADC configure failed with %d\n", ret);
> +		goto unlock;
> +	}
> +
> +	/* No support for polling mode at present*/
> +	rc = wait_for_completion_timeout(&adc->complete,
> +					msecs_to_jiffies(ADC5_GEN3_CONV_TIMEOUT_MS));
> +	if (!rc) {
> +		dev_err(adc->dev, "Reading ADC channel %s timed out\n",
> +			prop->label);
> +		ret = -ETIMEDOUT;
> +		goto unlock;
> +	}
> +
> +	ret = adc5_gen3_read_voltage_data(adc, data_volt, sdam_index);
> +	if (ret)
> +		goto unlock;
> +
> +	val = BIT(0);
> +	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_EOC_CLR, &val, 1);
> +	if (ret)
> +		goto unlock;
> +
> +	/* To indicate conversion request is only to clear a status */
> +	val = 0;
> +	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
> +	if (ret)
> +		goto unlock;
> +
> +	val = ADC5_GEN3_CONV_REQ_REQ;
> +	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
> +
> +unlock:
> +	mutex_unlock(&adc->lock);

guard(mutex)(&adc->lock); when you take the lock will simplify this funciton
as you can return directly then.

> +
> +	return ret;
> +}

> +static void tm_handler_work(struct work_struct *work)
> +{
> +	struct adc5_chip *adc = container_of(work, struct adc5_chip, tm_handler_work);
> +	struct adc5_channel_prop *chan_prop;
> +	u8 tm_status[2] = {0};
> +	u8 buf[16] = {0};
> +	u8 val;
> +	int ret, i, sdam_index = -1;
> +
> +	for (i = 0; i < adc->nchannels; i++) {
> +		bool upper_set = false, lower_set = false;
> +		int temp, offset;
> +		u16 code = 0;
> +
> +		chan_prop = &adc->chan_props[i];
> +		offset = chan_prop->tm_chan_index;
> +
> +		if (!chan_prop->adc_tm)
> +			continue;
> +
> +		mutex_lock(&adc->lock);
> +		if (chan_prop->sdam_index != sdam_index) {

Perhaps factor this block out as indent already high and adding scoped_guard would
make it worse.

> +			sdam_index = chan_prop->sdam_index;
> +			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS,
> +					tm_status, 2);
> +			if (ret) {
> +				dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
> +				goto out;
> +			}
> +
> +			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS_CLR,
> +					tm_status, 2);
> +			if (ret) {
> +				dev_err(adc->dev, "adc write TM status failed with %d\n", ret);
> +				goto out;
> +			}
> +
> +			/* To indicate conversion request is only to clear a status */
> +			val = 0;
> +			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
> +			if (ret) {
> +				dev_err(adc->dev, "adc write status clear conv_req failed with %d\n",
> +						ret);
> +				goto out;
> +			}
> +
> +			val = ADC5_GEN3_CONV_REQ_REQ;
> +			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
> +			if (ret) {
> +				dev_err(adc->dev, "adc write conv_req failed with %d\n", ret);
> +				goto out;
> +			}
> +
> +			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CH_DATA0(0), buf,
> +					sizeof(buf));
> +			if (ret < 0) {
> +				dev_err(adc->dev, "adc read data failed with %d\n", ret);
> +				goto out;
> +			}
> +		}
> +
> +		if ((tm_status[0] & BIT(offset)) && (chan_prop->high_thr_en))
> +			upper_set = true;
> +
> +		if ((tm_status[1] & BIT(offset)) && (chan_prop->low_thr_en))
> +			lower_set = true;
> +
> +		mutex_unlock(&adc->lock);
> +
> +		if (!(upper_set || lower_set))
> +			continue;
> +
> +		code = get_unaligned_le16(&buf[2 * offset]);
> +		pr_debug("ADC_TM threshold code:%#x\n", code);
> +
> +		ret = qcom_adc5_hw_scale(chan_prop->scale_fn_type,
> +			chan_prop->prescale, adc->data, code, &temp);
> +		if (ret) {
> +			dev_err(adc->dev, "Invalid temperature reading, ret = %d, code=%#x\n",
> +					ret, code);
> +			continue;
> +		}
> +
> +		chan_prop->last_temp = temp;
> +		chan_prop->last_temp_set = true;
> +		thermal_zone_device_update(chan_prop->tzd, THERMAL_TRIP_VIOLATED);
> +	}
> +
> +	return;
> +
> +out:
> +	mutex_unlock(&adc->lock);

Messy to do this. Can you use scoped_guard(mutex, &adc->lock) to handle it more
cleanly?

> +}
> +

> +
> +static int adc5_gen3_read_raw(struct iio_dev *indio_dev,
> +			 struct iio_chan_spec const *chan, int *val, int *val2,
> +			 long mask)
> +{
> +	struct adc5_chip *adc = iio_priv(indio_dev);
> +	struct adc5_channel_prop *prop;
> +	u16 adc_code_volt;
> +	int ret;
> +
> +	prop = &adc->chan_props[chan->address];
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_PROCESSED:
> +		ret = adc5_gen3_do_conversion(adc, prop,
> +					&adc_code_volt);
> +		if (ret)
> +			return ret;
> +
> +		ret = qcom_adc5_hw_scale(prop->scale_fn_type,
> +			prop->prescale, adc->data,
> +			adc_code_volt, val);
> +		if (ret)
> +			return ret;
> +
> +		return IIO_VAL_INT;
> +	case IIO_CHAN_INFO_RAW:
> +		ret = adc5_gen3_do_conversion(adc, prop,
> +					&adc_code_volt);
Very short line wrap.  Will be under 80 chars without it.
Please check for similar cases.

> +		if (ret)
> +			return ret;
> +		*val = (int)adc_code_volt;
> +		return IIO_VAL_INT;
> +	default:
> +		return -EINVAL;
> +	}
> +}

> +
> +static void adc5_gen3_disable(void *data)
> +{
> +	struct adc5_chip *adc = data;
> +	int i;
> +
> +	if (adc->n_tm_channels)
> +		cancel_work_sync(&adc->tm_handler_work);
If this is required before the place where a simple
devm_request_irq() will result in the irqs being cleaned up
them register this callback earlier to avoid problems there.

> +
> +	for (i = 0; i < adc->num_sdams; i++)
> +		free_irq(adc->base[i].irq, adc);
> +
> +	mutex_lock(&adc->lock);
> +	/* Disable all available TM channels */
> +	for (i = 0; i < adc->nchannels; i++) {
> +		if (!adc->chan_props[i].adc_tm)
> +			continue;
> +		adc5_gen3_poll_wait_hs(adc, adc->chan_props[i].sdam_index);
> +		_adc_tm5_gen3_disable_channel(&adc->chan_props[i]);
> +	}
> +
> +	mutex_unlock(&adc->lock);
> +}

> +static int adc5_gen3_get_fw_channel_data(struct adc5_chip *adc,
> +				    struct adc5_channel_prop *prop,
> +				    struct fwnode_handle *fwnode,
> +				    const struct adc5_data *data)
> +{
> +	const char *name = fwnode_get_name(fwnode);
> +	const char *channel_name;
> +	struct device *dev = adc->dev;
> +	u32 chan, value, varr[2], sid = 0;
> +	int ret, val;
> +
> +	ret = fwnode_property_read_u32(fwnode, "reg", &chan);
> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "invalid channel number %s\n", name);
> +
> +	/*
> +	 * Value read from "reg" is virtual channel number
> +	 * virtual channel number = sid << 8 | channel number
> +	 */
> +
> +	sid = FIELD_GET(ADC5_GEN3_VIRTUAL_SID_MASK, chan);
> +	chan = FIELD_GET(ADC5_GEN3_CHANNEL_MASK, chan);
> +
> +	if (chan > ADC5_GEN3_OFFSET_EXT2)
> +		return dev_err_probe(dev, -EINVAL, "%s invalid channel number %d\n", name, chan);
> +
> +	prop->channel = chan;
> +	prop->sid = sid;
> +
> +	ret = fwnode_property_read_string(fwnode, "label", &channel_name);
> +	if (ret)
> +		channel_name = name;
Set this first then don't check ret

	channel_name = name;
	fwnode_property_read_string()

do similar for any other cases with a default.

> +	prop->label = channel_name;
> +
> +	prop->decimation = ADC5_DECIMATION_DEFAULT;
> +	ret = fwnode_property_read_u32(fwnode, "qcom,decimation", &value);
> +	if (!ret) {
> +		ret = qcom_adc5_decimation_from_dt(value, data->decimation);
> +		if (ret < 0)
> +			return dev_err_probe(dev, ret, "%#x invalid decimation %d\n",
> +				chan, value);
> +		prop->decimation = ret;
> +	}
> +
> +	prop->prescale = adc->data->adc_chans[prop->channel].prescale_index;
> +	ret = fwnode_property_read_u32_array(fwnode, "qcom,pre-scaling", varr, 2);
> +	if (!ret) {
> +		ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
> +		if (ret < 0)
> +			return dev_err_probe(dev, ret, "%#x invalid pre-scaling <%d %d>\n",
> +				chan, varr[0], varr[1]);
> +		prop->prescale = ret;
> +	}
> +
> +	prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;

I'd prefer to see you has through the value that maps to this after qcom_adc5_hw_settle_time_from_dt
so then you can just set a default in value and call the rest of the code unconditionally.
Same for the cases that follow.

> +	ret = fwnode_property_read_u32(fwnode, "qcom,hw-settle-time", &value);
> +	if (!ret) {
> +		ret = qcom_adc5_hw_settle_time_from_dt(value,
> +						data->hw_settle_1);
> +		if (ret < 0)
> +			return dev_err_probe(dev, ret, "%#x invalid hw-settle-time %d us\n",
> +				chan, value);
> +		prop->hw_settle_time = ret;
> +	}
> +
> +	prop->avg_samples = VADC_DEF_AVG_SAMPLES;
> +	ret = fwnode_property_read_u32(fwnode, "qcom,avg-samples", &value);
> +	if (!ret) {
> +		ret = qcom_adc5_avg_samples_from_dt(value);
> +		if (ret < 0)
> +			return dev_err_probe(dev, ret, "%#x invalid avg-samples %d\n",
> +				chan, value);
> +		prop->avg_samples = ret;
> +	}
> +
> +	if (fwnode_property_read_bool(fwnode, "qcom,ratiometric"))
> +		prop->cal_method = ADC5_RATIOMETRIC_CAL;
> +	else
> +		prop->cal_method = ADC5_ABSOLUTE_CAL;
> +
> +	prop->timer = MEAS_INT_IMMEDIATE;
> +
> +	prop->adc_tm = fwnode_property_read_bool(fwnode, "qcom,adc-tm");
> +
> +	if (prop->adc_tm) {
> +		adc->n_tm_channels++;
> +		if (adc->n_tm_channels > ((adc->num_sdams * 8) - 1))
> +			return dev_err_probe(adc->dev, -EINVAL,
> +				"Number of TM nodes %u greater than channels supported:%u\n",
> +				adc->n_tm_channels, (adc->num_sdams * 8) - 1);
> +
> +		val = adc->n_tm_channels / 8;
> +		prop->sdam_index = val;
> +		prop->tm_chan_index = adc->n_tm_channels - (8*val);
> +
> +		prop->timer = MEAS_INT_1S;
> +	}
> +
> +	return 0;
> +}
>
> +static const struct of_device_id adc5_match_table[] = {
> +	{
> +		.compatible = "qcom,spmi-adc5-gen3",
> +		.data = &adc5_gen3_data_pmic,
> +	},
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, adc5_match_table);
> +
> +static int adc5_get_fw_data(struct adc5_chip *adc)
> +{
> +	const struct adc5_channels *adc_chan;
> +	struct iio_chan_spec *iio_chan;
> +	struct adc5_channel_prop *chan_props;
> +	struct fwnode_handle *child;
> +	unsigned int index = 0;
> +	int ret;
> +
> +	adc->nchannels = device_get_child_node_count(adc->dev);
> +	if (!adc->nchannels)
> +		return -EINVAL;
> +
> +	adc->iio_chans = devm_kcalloc(adc->dev, adc->nchannels,
> +				       sizeof(*adc->iio_chans), GFP_KERNEL);
> +	if (!adc->iio_chans)
> +		return -ENOMEM;
> +
> +	adc->chan_props = devm_kcalloc(adc->dev, adc->nchannels,
> +					sizeof(*adc->chan_props), GFP_KERNEL);
> +	if (!adc->chan_props)
> +		return -ENOMEM;
> +
> +	chan_props = adc->chan_props;
> +	adc->n_tm_channels = 0;
> +	iio_chan = adc->iio_chans;
> +	adc->data = device_get_match_data(adc->dev);
> +	if (!adc->data)
> +		adc->data = &adc5_gen3_data_pmic;

Why do you need a default?  Add a comment so we remember the reasoning.


> +
> +	device_for_each_child_node(adc->dev, child) {
> +		ret = adc5_gen3_get_fw_channel_data(adc, chan_props, child, adc->data);
> +		if (ret < 0) {
> +			fwnode_handle_put(child);
I've just sent out automated cleanup handling for this. Not a huge
saving here, but if you want to:
https://lore.kernel.org/linux-iio/20240101172611.694830-1-jic23@kernel.org/T/#t


> +			return ret;
> +		}
> +
> +		chan_props->chip = adc;
> +		chan_props->scale_fn_type =
> +			adc->data->adc_chans[chan_props->channel].scale_fn_type;
> +		adc_chan = &adc->data->adc_chans[chan_props->channel];
> +		iio_chan->channel = V_CHAN(*chan_props);
> +		iio_chan->info_mask_separate = adc_chan->info_mask;
> +		iio_chan->type = adc_chan->type;
> +		iio_chan->address = index;
> +		iio_chan->indexed = 1;
> +		iio_chan++;
> +		chan_props++;
> +		index++;
> +	}
> +
> +	return 0;
> +}
> +
> +static int adc5_gen3_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct iio_dev *indio_dev;
> +	struct adc5_chip *adc;
> +	struct regmap *regmap;
> +	int ret, i;
> +	u32 *reg;
> +
> +	regmap = dev_get_regmap(dev->parent, NULL);
> +	if (!regmap)
> +		return -ENODEV;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	adc = iio_priv(indio_dev);
> +	adc->regmap = regmap;
> +	adc->dev = dev;
> +
> +	ret = device_property_count_u32(dev, "reg");
> +	if (ret < 0)
> +		return ret;
> +
> +	adc->num_sdams = ret;
> +
> +	reg = kcalloc(adc->num_sdams, sizeof(u32), GFP_KERNEL);

> +	if (!reg)
> +		return -ENOMEM;
> +
> +	ret = device_property_read_u32_array(dev, "reg", reg, adc->num_sdams);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Failed to read reg property, ret = %d\n", ret);
> +
> +	adc->base = devm_kcalloc(dev, adc->num_sdams, sizeof(*adc->base), GFP_KERNEL);
> +	if (!adc->base)
> +		return -ENOMEM;
> +
> +	platform_set_drvdata(pdev, indio_dev);
> +	init_completion(&adc->complete);
> +	mutex_init(&adc->lock);
> +
> +	for (i = 0; i < adc->num_sdams; i++) {
> +		adc->base[i].base_addr = reg[i];
> +
> +		adc->base[i].irq_name = devm_kasprintf(dev, GFP_KERNEL, "adc-sdam%d", i);
> +		if (!adc->base[i].irq_name) {
> +			kfree(reg);
> +			ret = -ENOMEM;
> +			goto err_irq;
> +		}
> +
> +		ret = platform_get_irq_byname(pdev, adc->base[i].irq_name);
> +		if (ret < 0) {
> +			kfree(reg);
> +			dev_err(dev, "Getting IRQ %d by name failed, ret = %d\n",
> +					adc->base[i].irq, ret);
> +			goto err_irq;
> +		}
> +		adc->base[i].irq = ret;
> +
> +		ret = request_irq(adc->base[i].irq, adc5_gen3_isr, 0, adc->base[i].irq_name, adc);

Don't mix devm and non dev calls.  And don't group up multiple things in one devm callback
as it almost always leads to bugs where for example only some irqs are allocated.

> +		if (ret < 0) {
> +			kfree(reg);
> +			dev_err(dev, "Failed to request SDAM%d irq, ret = %d\n", i, ret);
> +			goto err_irq;
> +		}
> +	}
> +	kfree(reg);

I would factor out this code and allocation of reg so you can easily use scope
based cleanup (see linux/cleanup.h) to avoid the kfree(reg) entries that
make for awkward code flow.



> +
> +	ret = devm_add_action(dev, adc5_gen3_disable, adc);
As above, this action does multiple things. Also use devm_add_action_or_reset() to cleanup
if the devm registration fails without needing to do it manually.

> +	if (ret < 0) {
> +		dev_err(dev, "failed to register adc disablement devm action, %d\n", ret);
> +		goto err_irq;
> +	}
> +
> +	ret = adc5_get_fw_data(adc);
> +	if (ret < 0) {
> +		dev_err(dev, "adc get dt data failed, ret = %d\n", ret);
> +		goto err_irq;

Fairly sure this results in a double free of the irqs.
Use devm_request_irq() in the first place and let the normal handling clean them
up both in the error path and in the remove path.

> +	}
> +
> +	ret = adc_tm_register_tzd(adc);
> +	if (ret < 0)
> +		goto err_irq;
> +
> +	if (adc->n_tm_channels)
> +		INIT_WORK(&adc->tm_handler_work, tm_handler_work);

Until this init work seems unlikely you should be calling the cancel
work in gen3_disable()


> +
> +	indio_dev->name = pdev->name;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +	indio_dev->info = &adc5_gen3_info;
> +	indio_dev->channels = adc->iio_chans;
> +	indio_dev->num_channels = adc->nchannels;
> +
> +	ret = devm_iio_device_register(dev, indio_dev);
> +	if (!ret)
> +		return 0;
Please keep error conditions as the out of line path.

	if (ret)
		goto err_irq;

	return 0;


> +
> +err_irq:
> +	for (i = 0; i < adc->num_sdams; i++)
> +		free_irq(adc->base[i].irq, adc);

Already freed by a devm cleanup handler.

> +
> +	return ret;
> +}
Jishnu Prakash Feb. 16, 2024, 11:44 a.m. UTC | #3
Hi Jonathan,

(Resending this mail for tracking on mailing lists, as it got rejected 
from lists the first time due to HTML)

On 1/1/2024 11:24 PM, Jonathan Cameron wrote:
> On Sun, 31 Dec 2023 22:42:37 +0530
> Jishnu Prakash <quic_jprakash@quicinc.com> wrote:
> 
>> The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
>> with all SW communication to ADC going through PMK8550 which
>> communicates with other PMICs through PBS.
>>


>> +
>> +	for (i = 0; i < adc->nchannels; i++) {
>> +		bool upper_set = false, lower_set = false;
>> +		int temp, offset;
>> +		u16 code = 0;
>> +
>> +		chan_prop = &adc->chan_props[i];
>> +		offset = chan_prop->tm_chan_index;
>> +
>> +		if (!chan_prop->adc_tm)
>> +			continue;
>> +
>> +		mutex_lock(&adc->lock);
>> +		if (chan_prop->sdam_index != sdam_index) {
> 
> Perhaps factor this block out as indent already high and adding scoped_guard would
> make it worse.

I don't think I can completely factor it out, as we need to update 
several local variables here (sdam_index, tm_status, buf, also chan_prop 
above), but I'll try to reduce it as much as possible.

> 
>> +			sdam_index = chan_prop->sdam_index;
>> +			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS,
>> +					tm_status, 2);
>> +			if (ret) {
>> +				dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
>> +				goto out;
>> +			}


>> +
>> +static void adc5_gen3_disable(void *data)
>> +{
>> +	struct adc5_chip *adc = data;
>> +	int i;
>> +
>> +	if (adc->n_tm_channels)
>> +		cancel_work_sync(&adc->tm_handler_work);
> If this is required before the place where a simple
> devm_request_irq() will result in the irqs being cleaned up
> them register this callback earlier to avoid problems there.
> 

On checking again, it looks like I can just use devm_request_irq() and 
avoid having to free irqs explicitly here and elsewhere. I'll  still 
need to call cancel_work_sync() and I think you have also asked me to 
keep this call in another comment below. I have another question for it 
below.

>> +
>> +	for (i = 0; i < adc->num_sdams; i++)
>> +		free_irq(adc->base[i].irq, adc);
>> +
>> +	mutex_lock(&adc->lock);
>> +	/* Disable all available TM channels */
>> +	for (i = 0; i < adc->nchannels; i++) {
>> +		if (!adc->chan_props[i].adc_tm)
>> +			continue;
>> +		adc5_gen3_poll_wait_hs(adc, adc->chan_props[i].sdam_index);
>> +		_adc_tm5_gen3_disable_channel(&adc->chan_props[i]);
>> +	}
>> +
>> +	mutex_unlock(&adc->lock);
>> +}
> 


>> +
>> +	prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
> 
> I'd prefer to see you has through the value that maps to this after qcom_adc5_hw_settle_time_from_dt
> so then you can just set a default in value and call the rest of the code unconditionally.
> Same for the cases that follow.

I can remove the return check for fwnode_property_read_u32() as you 
suggested, but I think we still need to keep the return check for 
qcom_adc5_hw_settle_time_from_dt(), to check in case values unsupported 
in this ADC HW are set in DT. Same for the other properties.

> 
>> +	ret = fwnode_property_read_u32(fwnode, "qcom,hw-settle-time", &value);
>> +	if (!ret) {
>> +		ret = qcom_adc5_hw_settle_time_from_dt(value,
>> +						data->hw_settle_1);
>> +		if (ret < 0)
>> +			return dev_err_probe(dev, ret, "%#x invalid hw-settle-time %d us\n",
>> +				chan, value);
>> +		prop->hw_settle_time = ret;
>> +	}
>> +


>> +
>> +	chan_props = adc->chan_props;
>> +	adc->n_tm_channels = 0;
>> +	iio_chan = adc->iio_chans;
>> +	adc->data = device_get_match_data(adc->dev);
>> +	if (!adc->data)
>> +		adc->data = &adc5_gen3_data_pmic;
> 
> Why do you need a default?  Add a comment so we remember the reasoning.

On second thought, this may not be needed, I'll remove this.

> 
> 
>> +
>> +	device_for_each_child_node(adc->dev, child) {
>> +		ret = adc5_gen3_get_fw_channel_data(adc, chan_props, child, adc->data);
>> +		if (ret < 0) {


>> +
>> +		ret = platform_get_irq_byname(pdev, adc->base[i].irq_name);
>> +		if (ret < 0) {
>> +			kfree(reg);
>> +			dev_err(dev, "Getting IRQ %d by name failed, ret = %d\n",
>> +					adc->base[i].irq, ret);
>> +			goto err_irq;
>> +		}
>> +		adc->base[i].irq = ret;
>> +
>> +		ret = request_irq(adc->base[i].irq, adc5_gen3_isr, 0, adc->base[i].irq_name, adc);
> 
> Don't mix devm and non dev calls.  And don't group up multiple things in one devm callback
> as it almost always leads to bugs where for example only some irqs are allocated.

I can replace request_irq() with devm_request_irq(). But when you say 
not to group up multiple things in one devm callback, do you mean the 
devm_add_action() callback I added below or something else right here?



> 
>> +		if (ret < 0) {
>> +			kfree(reg);
>> +			dev_err(dev, "Failed to request SDAM%d irq, ret = %d\n", i, ret);
>> +			goto err_irq;
>> +		}
>> +	}
>> +	kfree(reg);
> 
> I would factor out this code and allocation of reg so you can easily use scope
> based cleanup (see linux/cleanup.h) to avoid the kfree(reg) entries that
> make for awkward code flow.
> 

The kfrees are not really needed, I'll just use devm_kcalloc to allocate 
memory for the "reg" variable. With this and devm_request_irq, I think a 
scoped guard would not be needed here.


> 
> 
>> +
>> +	ret = devm_add_action(dev, adc5_gen3_disable, adc);
> As above, this action does multiple things. Also use devm_add_action_or_reset() to cleanup
> if the devm registration fails without needing to do it manually.

I'll change it to devm_add_action_or_reset(), but do you mean I should 
call devm_add_action_or_reset() twice to register two separate callbacks 
instead of just adc5_gen3_disable? Like one for calling 
cancel_work_sync() alone and the other for the loop where we disable all 
TM channels?


> 
>> +	if (ret < 0) {
>> +		dev_err(dev, "failed to register adc disablement devm action, %d\n", ret);
>> +		goto err_irq;
>> +	}
>> +


>> +
>> +	if (adc->n_tm_channels)
>> +		INIT_WORK(&adc->tm_handler_work, tm_handler_work);
> 
> Until this init work seems unlikely you should be calling the cancel
> work in gen3_disable()

We are already calling cancel_work_sync() in adc5_gen3_disable....is 
there any change needed?


I'll address all your other comments in the next patchset.


Thanks,

Jishnu

> 
> 
>> +
>> +	indio_dev->name = pdev->name;
>> +	indio_dev->modes = INDIO_DIRECT_MODE;
>> +	indio_dev->info = &adc5_gen3_info;
>> +	indio_dev->channels = adc->iio_chans;
>> +	indio_dev->num_channels = adc->nchannels;
>> +
>> +	ret = devm_iio_device_register(dev, indio_dev);
>> +	if (!ret)
>> +		return 0;
> Please keep error conditions as the out of line path.
> 
> 	if (ret)
> 		goto err_irq;
> 
> 	return 0;
> 
> 
>> +
>> +err_irq:
>> +	for (i = 0; i < adc->num_sdams; i++)
>> +		free_irq(adc->base[i].irq, adc);
> 
> Already freed by a devm cleanup handler.
> 
>> +
>> +	return ret;
>> +}
>
Jonathan Cameron Feb. 16, 2024, 1:54 p.m. UTC | #4
On Fri, 16 Feb 2024 16:10:18 +0530
Jishnu Prakash <quic_jprakash@quicinc.com> wrote:

> Hi Jonathan,
> 
> On 1/1/2024 11:24 PM, Jonathan Cameron wrote:
> > On Sun, 31 Dec 2023 22:42:37 +0530
> > Jishnu Prakash<quic_jprakash@quicinc.com>  wrote:
> >  
> >> The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
> >> with all SW communication to ADC going through PMK8550 which
> >> communicates with other PMICs through PBS.
> >>  
> 
> >> +
> >> +	for (i = 0; i < adc->nchannels; i++) {
> >> +		bool upper_set = false, lower_set = false;
> >> +		int temp, offset;
> >> +		u16 code = 0;
> >> +
> >> +		chan_prop = &adc->chan_props[i];
> >> +		offset = chan_prop->tm_chan_index;
> >> +
> >> +		if (!chan_prop->adc_tm)
> >> +			continue;
> >> +
> >> +		mutex_lock(&adc->lock);
> >> +		if (chan_prop->sdam_index != sdam_index) {  
> > Perhaps factor this block out as indent already high and adding scoped_guard would
> > make it worse.  
> 
> 
> I don't think I can completely factor it out, as we need to update 
> several local variables here (sdam_index, tm_status, buf, also chan_prop 
> above), but I'll try to reduce it as much as possible.
> 
> 
> >> +			sdam_index = chan_prop->sdam_index;
> >> +			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS,
> >> +					tm_status, 2);
> >> +			if (ret) {
> >> +				dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
> >> +				goto out;
> >> +			}
> >> +  
> 
> >> +
> >> +static void adc5_gen3_disable(void *data)
> >> +{
> >> +	struct adc5_chip *adc = data;
> >> +	int i;
> >> +
> >> +	if (adc->n_tm_channels)
> >> +		cancel_work_sync(&adc->tm_handler_work);  
> > If this is required before the place where a simple
> > devm_request_irq() will result in the irqs being cleaned up
> > them register this callback earlier to avoid problems there.  
> 
> 
> On checking again, it looks like I can just use devm_request_irq() and 
> avoid having to free irqs explicitly here and elsewhere. I'll  still 
> need to call cancel_work_sync() and I think you have also asked me to 
> keep this call in another comment below. I have another question for it 
> below.

Keeping it is fine, just make sure it's registered in the right location
to ensure it is taken down after we are sure it can't get scheduled again
(I think that is what I was getting at - been a while!)
> 
> 
> >> +
> >> +	for (i = 0; i < adc->num_sdams; i++)
> >> +		free_irq(adc->base[i].irq, adc);
> >> +
> >> +	mutex_lock(&adc->lock);
> >> +	/* Disable all available TM channels */
> >> +	for (i = 0; i < adc->nchannels; i++) {
> >> +		if (!adc->chan_props[i].adc_tm)
> >> +			continue;
> >> +		adc5_gen3_poll_wait_hs(adc, adc->chan_props[i].sdam_index);
> >> +		_adc_tm5_gen3_disable_channel(&adc->chan_props[i]);
> >> +	}
> >> +
> >> +	mutex_unlock(&adc->lock);
> >> +}  
> 
> > +  
> >> +	prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;  
> > I'd prefer to see you has through the value that maps to this after qcom_adc5_hw_settle_time_from_dt
> > so then you can just set a default in value and call the rest of the code unconditionally.
> > Same for the cases that follow.  
> 
> 
> I can remove the return check for fwnode_property_read_u32() as you 
> suggested, but I think we still need to keep the return check for 
> qcom_adc5_hw_settle_time_from_dt(), to check in case values unsupported 
> in this ADC HW are set in DT. Same for the other properties.

Sure, you can check for errors in using the property. Just do it unconditionally
so that you call the same code for the default (even though you know that will
be fine).  Should simplify the code.

> 
> 
> >> +	ret = fwnode_property_read_u32(fwnode, "qcom,hw-settle-time", &value);
> >> +	if (!ret) {
> >> +		ret = qcom_adc5_hw_settle_time_from_dt(value,
> >> +						data->hw_settle_1);
> >> +		if (ret < 0)
> >> +			return dev_err_probe(dev, ret, "%#x invalid hw-settle-time %d us\n",
> >> +				chan, value);
> >> +		prop->hw_settle_time = ret;
> >> +	}
> >> +  

> >  
> >> +
> >> +	device_for_each_child_node(adc->dev, child) {
> >> +		ret = adc5_gen3_get_fw_channel_data(adc, chan_props, child, adc->data);
> >> +		if (ret < 0) {  
> 
> >> +		ret = platform_get_irq_byname(pdev, adc->base[i].irq_name);
> >> +		if (ret < 0) {
> >> +			kfree(reg);
> >> +			dev_err(dev, "Getting IRQ %d by name failed, ret = %d\n",
> >> +					adc->base[i].irq, ret);
> >> +			goto err_irq;
> >> +		}
> >> +		adc->base[i].irq = ret;
> >> +
> >> +		ret = request_irq(adc->base[i].irq, adc5_gen3_isr, 0, adc->base[i].irq_name, adc);  
> > Don't mix devm and non dev calls.  And don't group up multiple things in one devm callback
> > as it almost always leads to bugs where for example only some irqs are allocated.  
> 
> 
> I can replace request_irq() with devm_request_irq(). But when you say 
> not to group up multiple things in one devm callback, do you mean the 
> devm_add_action() callback I added below or something else right here?

Yes, I meant the devm_add_action() callback.

> 
> 
> >> +		if (ret < 0) {
> >> +			kfree(reg);
> >> +			dev_err(dev, "Failed to request SDAM%d irq, ret = %d\n", i, ret);
> >> +			goto err_irq;
> >> +		}
> >> +	}
> >> +	kfree(reg);  
> > I would factor out this code and allocation of reg so you can easily use scope
> > based cleanup (see linux/cleanup.h) to avoid the kfree(reg) entries that
> > make for awkward code flow.  
> 
> 
> The kfrees are not really needed, I'll just use devm_kcalloc to allocate 
> memory for the "reg" variable. With this and devm_request_irq, I think a 
> scoped guard would not be needed here.

If you don't need it after this function, then better to clean it up.

> 
> 
> >
> >  
> >> +
> >> +	ret = devm_add_action(dev, adc5_gen3_disable, adc);  
> > As above, this action does multiple things. Also use devm_add_action_or_reset() to cleanup
> > if the devm registration fails without needing to do it manually.  
> 
> 
> I'll change it to devm_add_action_or_reset(), but do you mean I should 
> call devm_add_action_or_reset() twice to register two separate callbacks 
> instead of just adc5_gen3_disable? Like one for calling 
> cancel_work_sync() alone and the other for the loop where we disable all 
> TM channels?

yes

> 
> 
> >> +	if (ret < 0) {
> >> +		dev_err(dev, "failed to register adc disablement devm action, %d\n", ret);
> >> +		goto err_irq;
> >> +	}
> >> +  
> 
> >> +
> >> +	if (adc->n_tm_channels)
> >> +		INIT_WORK(&adc->tm_handler_work, tm_handler_work);  
> > Until this init work seems unlikely you should be calling the cancel
> > work in gen3_disable()  
> 
> 
> We are already calling cancel_work_sync() in adc5_gen3_disable....is 
> there any change needed?
Yes - add a devm_add_action() here (not need for reset in this case as nothing
can have queued any work yet) and handle this on it's own.

Each cleanup action should match with a setup action.

Jonathan
diff mbox series

Patch

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 4eebd5161419..4bdd5bb5b3fc 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -997,6 +997,31 @@  config QCOM_SPMI_ADC5
 	  To compile this driver as a module, choose M here: the module will
 	  be called qcom-spmi-adc5.
 
+config QCOM_SPMI_ADC5_GEN3
+	tristate "Qualcomm Technologies Inc. SPMI PMIC5 GEN3 ADC"
+	depends on SPMI && THERMAL
+	select REGMAP_SPMI
+	select QCOM_VADC_COMMON
+	help
+	  This is the IIO Voltage PMIC5 Gen3 ADC driver for Qualcomm Technologies Inc. PMICs.
+
+	  The driver supports reading multiple channels. The ADC is a 16-bit
+	  sigma-delta ADC. The hardware supports calibrated results for
+	  conversion requests and clients include reading phone power supply
+	  voltage, on board system thermistors connected to the PMIC ADC,
+	  PMIC die temperature, charger temperature, battery current, USB voltage
+	  input and voltage signals connected to supported PMIC GPIO pins. The
+	  hardware supports internal pull-up for thermistors and can choose between
+	  a 30k, 100k or 400k ohm pull up using the ADC channels.
+
+	  In addition, the same driver supports ADC thermal monitoring devices too.
+	  They appear as thermal zones with multiple trip points. A thermal client sets
+	  threshold temperature for both warm and cool trips and gets updated when a
+	  threshold is reached.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called qcom-spmi-adc5-gen3.
+
 config RCAR_GYRO_ADC
 	tristate "Renesas R-Car GyroADC driver"
 	depends on ARCH_RCAR_GEN2 || COMPILE_TEST
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index c0803383a7cc..539af17a668f 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -86,6 +86,7 @@  obj-$(CONFIG_NAU7802) += nau7802.o
 obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
 obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
 obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
+obj-$(CONFIG_QCOM_SPMI_ADC5_GEN3) += qcom-spmi-adc5-gen3.o
 obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
 obj-$(CONFIG_QCOM_SPMI_RRADC) += qcom-spmi-rradc.o
 obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
diff --git a/drivers/iio/adc/qcom-spmi-adc5-gen3.c b/drivers/iio/adc/qcom-spmi-adc5-gen3.c
new file mode 100644
index 000000000000..5b5848492245
--- /dev/null
+++ b/drivers/iio/adc/qcom-spmi-adc5-gen3.c
@@ -0,0 +1,1198 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <asm/unaligned.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#include <dt-bindings/iio/adc/qcom,spmi-vadc.h>
+
+#define ADC5_GEN3_HS				0x45
+#define ADC5_GEN3_HS_BUSY			BIT(7)
+#define ADC5_GEN3_HS_READY			BIT(0)
+
+#define ADC5_GEN3_STATUS1			0x46
+#define ADC5_GEN3_STATUS1_CONV_FAULT		BIT(7)
+#define ADC5_GEN3_STATUS1_THR_CROSS		BIT(6)
+#define ADC5_GEN3_STATUS1_EOC			BIT(0)
+
+#define ADC5_GEN3_TM_EN_STS			0x47
+#define ADC5_GEN3_TM_HIGH_STS			0x48
+#define ADC5_GEN3_TM_LOW_STS			0x49
+
+#define ADC5_GEN3_EOC_STS			0x4a
+#define ADC5_GEN3_EOC_CHAN_0			BIT(0)
+
+#define ADC5_GEN3_EOC_CLR			0x4b
+#define ADC5_GEN3_TM_HIGH_STS_CLR		0x4c
+#define ADC5_GEN3_TM_LOW_STS_CLR		0x4d
+#define ADC5_GEN3_CONV_ERR_CLR			0x4e
+#define ADC5_GEN3_CONV_ERR_CLR_REQ		BIT(0)
+
+#define ADC5_GEN3_SID				0x4f
+#define ADC5_GEN3_SID_MASK			GENMASK(3, 0)
+
+#define ADC5_GEN3_PERPH_CH			0x50
+#define ADC5_GEN3_CHAN_CONV_REQ			BIT(7)
+
+#define ADC5_GEN3_TIMER_SEL			0x51
+#define ADC5_GEN3_TIME_IMMEDIATE		0x1
+
+#define ADC5_GEN3_DIG_PARAM			0x52
+#define ADC5_GEN3_DIG_PARAM_CAL_SEL_MASK	GENMASK(5, 4)
+#define ADC5_GEN3_DIG_PARAM_DEC_RATIO_SEL_MASK	GENMASK(3, 2)
+
+#define ADC5_GEN3_FAST_AVG			0x53
+#define ADC5_GEN3_FAST_AVG_CTL_EN		BIT(7)
+#define ADC5_GEN3_FAST_AVG_CTL_SAMPLES_MASK	GENMASK(2, 0)
+
+#define ADC5_GEN3_ADC_CH_SEL_CTL		0x54
+#define ADC5_GEN3_DELAY_CTL			0x55
+#define ADC5_GEN3_HW_SETTLE_DELAY_MASK		GENMASK(3, 0)
+
+#define ADC5_GEN3_CH_EN				0x56
+#define ADC5_GEN3_HIGH_THR_INT_EN		BIT(1)
+#define ADC5_GEN3_LOW_THR_INT_EN		BIT(0)
+
+#define ADC5_GEN3_LOW_THR0			0x57
+#define ADC5_GEN3_LOW_THR1			0x58
+#define ADC5_GEN3_HIGH_THR0			0x59
+#define ADC5_GEN3_HIGH_THR1			0x5a
+
+#define ADC5_GEN3_CH_DATA0(channel)	(0x5c + (channel) * 2)
+#define ADC5_GEN3_CH_DATA1(channel)	(0x5d + (channel) * 2)
+
+#define ADC5_GEN3_CONV_REQ			0xe5
+#define ADC5_GEN3_CONV_REQ_REQ			BIT(0)
+
+#define ADC5_GEN3_VIRTUAL_SID_MASK			GENMASK(15, 8)
+#define ADC5_GEN3_CHANNEL_MASK			GENMASK(7, 0)
+#define V_CHAN(x)		\
+	(FIELD_PREP(ADC5_GEN3_VIRTUAL_SID_MASK, (x).sid) | (x).channel)	\
+
+enum adc5_cal_method {
+	ADC5_NO_CAL = 0,
+	ADC5_RATIOMETRIC_CAL,
+	ADC5_ABSOLUTE_CAL
+};
+
+enum adc5_time_select {
+	MEAS_INT_DISABLE = 0,
+	MEAS_INT_IMMEDIATE,
+	MEAS_INT_50MS,
+	MEAS_INT_100MS,
+	MEAS_INT_1S,
+	MEAS_INT_NONE,
+};
+
+struct adc5_sdam_data {
+	u16			base_addr;
+	const char		*irq_name;
+	int			irq;
+};
+
+/**
+ * struct adc5_channel_prop - ADC channel property.
+ * @channel: channel number, refer to the channel list.
+ * @cal_method: calibration method.
+ * @decimation: sampling rate supported for the channel.
+ * @sid: slave id of PMIC owning the channel.
+ * @prescale: channel scaling performed on the input signal.
+ * @hw_settle_time: the time between AMUX being configured and the
+ *	start of conversion.
+ * @avg_samples: ability to provide single result from the ADC
+ *	that is an average of multiple measurements.
+ * @sdam_index: Index for which SDAM this channel is on.
+ * @scale_fn_type: Represents the scaling function to convert voltage
+ *	physical units desired by the client for the channel.
+ * @label: Channel name used in device tree.
+ * @chip: pointer to top-level ADC device structure.
+ * @adc_tm: indicates if the channel is used for TM measurements.
+ * @tm_chan_index: TM channel number used (ranging from 1-7).
+ * @timer: time period of recurring TM measurement.
+ * @tzd: pointer to thermal device corresponding to TM channel.
+ * @high_thr_en: TM high threshold crossing detection enabled.
+ * @low_thr_en: TM low threshold crossing detection enabled.
+ * @last_temp: last temperature that caused threshold violation,
+ *	or a thermal TM channel.
+ * @last_temp_set: indicates if last_temp is stored.
+ */
+struct adc5_channel_prop {
+	unsigned int			channel;
+	enum adc5_cal_method		cal_method;
+	unsigned int			decimation;
+	unsigned int			sid;
+	unsigned int			prescale;
+	unsigned int			hw_settle_time;
+	unsigned int			avg_samples;
+	unsigned int			sdam_index;
+
+	enum vadc_scale_fn_type		scale_fn_type;
+	const char			*label;
+
+	struct adc5_chip		*chip;
+	/* TM(thermal monitoring related) properties */
+	bool				adc_tm;
+	unsigned int			tm_chan_index;
+	unsigned int			timer;
+	struct thermal_zone_device	*tzd;
+	bool				high_thr_en;
+	bool				low_thr_en;
+	int				last_temp;
+	bool				last_temp_set;
+};
+
+/**
+ * struct adc5_chip - ADC private structure.
+ * @regmap: SPMI ADC5 Gen3 peripheral register map field.
+ * @dev: SPMI ADC5 Gen3 device.
+ * @base: pointer to array of ADC peripheral base and interrupt.
+ * @num_sdams: number of SDAMs (Shared Direct Access Memory Module) being used.
+ * @nchannels: number of ADC channels.
+ * @chan_props: array of ADC channel properties.
+ * @iio_chans: array of IIO channels specification.
+ * @complete: ADC result notification after interrupt is received.
+ * @lock: ADC lock for access to the peripheral, to prevent concurrent
+ * requests from multiple clients.
+ * @data: software configuration data.
+ * @n_tm_channels: number of ADC channels used for TM measurements.
+ * @tm_handler_work: scheduled work for handling TM threshold violation.
+ */
+struct adc5_chip {
+	struct regmap			*regmap;
+	struct device			*dev;
+	struct adc5_sdam_data		*base;
+	unsigned int			num_sdams;
+	unsigned int			nchannels;
+	struct adc5_channel_prop	*chan_props;
+	struct iio_chan_spec		*iio_chans;
+	struct completion		complete;
+	struct mutex			lock;
+	const struct adc5_data		*data;
+	/* TM properties */
+	unsigned int			n_tm_channels;
+	struct work_struct		tm_handler_work;
+};
+
+static int adc5_gen3_read(struct adc5_chip *adc, unsigned int sdam_index,
+				u16 offset, u8 *data, int len)
+{
+	return regmap_bulk_read(adc->regmap, adc->base[sdam_index].base_addr + offset, data, len);
+}
+
+static int adc5_gen3_write(struct adc5_chip *adc, unsigned int sdam_index,
+				u16 offset, u8 *data, int len)
+{
+	return regmap_bulk_write(adc->regmap, adc->base[sdam_index].base_addr + offset, data, len);
+}
+
+static int adc5_gen3_read_voltage_data(struct adc5_chip *adc, u16 *data, u8 sdam_index)
+{
+	int ret;
+	u8 rslt[2];
+
+	ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CH_DATA0(0), rslt, 2);
+	if (ret)
+		return ret;
+
+	*data = get_unaligned_le16(rslt);
+
+	if (*data == ADC5_USR_DATA_CHECK) {
+		dev_err(adc->dev, "Invalid data:%#x\n", *data);
+		return -EINVAL;
+	}
+
+	dev_dbg(adc->dev, "voltage raw code:%#x\n", *data);
+
+	return 0;
+}
+
+static void adc5_gen3_update_dig_param(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop, u8 *data)
+{
+	/* Update calibration select and decimation ratio select*/
+	*data &= ~(ADC5_GEN3_DIG_PARAM_CAL_SEL_MASK | ADC5_GEN3_DIG_PARAM_DEC_RATIO_SEL_MASK);
+	*data |= FIELD_PREP(ADC5_GEN3_DIG_PARAM_CAL_SEL_MASK, prop->cal_method);
+	*data |= FIELD_PREP(ADC5_GEN3_DIG_PARAM_DEC_RATIO_SEL_MASK, prop->decimation);
+}
+
+# define ADC5_GEN3_READ_CONFIG_REGS 7
+
+static int adc5_gen3_configure(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop)
+{
+	u8 sdam_index = prop->sdam_index;
+	u8 conv_req = 0;
+	u8 buf[ADC5_GEN3_READ_CONFIG_REGS];
+	int ret;
+
+	/* Reserve channel 0 of first SDAM for immediate conversions */
+	if (prop->adc_tm)
+		sdam_index = 0;
+
+	ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	/* Write SID */
+	buf[0] = FIELD_PREP(ADC5_GEN3_SID_MASK, prop->sid);
+
+	/*
+	 * Use channel 0 by default for immediate conversion and
+	 * to indicate there is an actual conversion request
+	 */
+	buf[1] = ADC5_GEN3_CHAN_CONV_REQ | 0;
+
+	buf[2] = ADC5_GEN3_TIME_IMMEDIATE;
+
+	/* Digital param selection */
+	adc5_gen3_update_dig_param(adc, prop, &buf[3]);
+
+	/* Update fast average sample value */
+	buf[4] &= ~ADC5_GEN3_FAST_AVG_CTL_SAMPLES_MASK;
+	buf[4] |= prop->avg_samples | ADC5_GEN3_FAST_AVG_CTL_EN;
+
+	/* Select ADC channel */
+	buf[5] = prop->channel;
+
+	/* Select HW settle delay for channel */
+	buf[6] = FIELD_PREP(ADC5_GEN3_HW_SETTLE_DELAY_MASK, prop->hw_settle_time);
+
+	reinit_completion(&adc->complete);
+
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	conv_req = ADC5_GEN3_CONV_REQ_REQ;
+	return adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &conv_req, 1);
+}
+
+/**
+ * Worst case delay from PBS in readying handshake bit
+ * can be up to 15ms, when PBS is busy running other
+ * simultaneous transactions, while in the best case, it is
+ * already ready at this point. Assigning polling delay and
+ * retry count accordingly.
+ */
+
+#define ADC5_GEN3_HS_DELAY_MIN_US		100
+#define ADC5_GEN3_HS_DELAY_MAX_US		110
+#define ADC5_GEN3_HS_RETRY_COUNT		150
+
+static int adc5_gen3_poll_wait_hs(struct adc5_chip *adc,
+				unsigned int sdam_index)
+{
+	u8 conv_req = ADC5_GEN3_CONV_REQ_REQ;
+	u8 status = 0;
+	int ret, count;
+
+	for (count = 0; count < ADC5_GEN3_HS_RETRY_COUNT; count++) {
+		ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_HS, &status, 1);
+		if (ret)
+			return ret;
+
+		if (status == ADC5_GEN3_HS_READY) {
+			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CONV_REQ,
+					&conv_req, 1);
+			if (ret)
+				return ret;
+
+			if (!conv_req)
+				return 0;
+		}
+
+		usleep_range(ADC5_GEN3_HS_DELAY_MIN_US,
+			ADC5_GEN3_HS_DELAY_MAX_US);
+	}
+
+	dev_err(adc->dev, "Setting HS ready bit timed out, status:%#x\n", status);
+	return -ETIMEDOUT;
+}
+
+/**
+ * Worst case delay from PBS for conversion time can be
+ * up to 500ms, when PBS has timed out twice, once for
+ * the initial attempt and once for a retry of the same
+ * transaction.
+ */
+
+#define ADC5_GEN3_CONV_TIMEOUT_MS	501
+
+static int adc5_gen3_do_conversion(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop,
+			u16 *data_volt)
+{
+	u8 val, sdam_index = prop->sdam_index;
+	unsigned long rc;
+	int ret;
+
+	/* Reserve channel 0 of first SDAM for immediate conversions */
+	if (prop->adc_tm)
+		sdam_index = 0;
+
+	mutex_lock(&adc->lock);
+	ret = adc5_gen3_poll_wait_hs(adc, 0);
+	if (ret)
+		goto unlock;
+
+	ret = adc5_gen3_configure(adc, prop);
+	if (ret) {
+		dev_err(adc->dev, "ADC configure failed with %d\n", ret);
+		goto unlock;
+	}
+
+	/* No support for polling mode at present*/
+	rc = wait_for_completion_timeout(&adc->complete,
+					msecs_to_jiffies(ADC5_GEN3_CONV_TIMEOUT_MS));
+	if (!rc) {
+		dev_err(adc->dev, "Reading ADC channel %s timed out\n",
+			prop->label);
+		ret = -ETIMEDOUT;
+		goto unlock;
+	}
+
+	ret = adc5_gen3_read_voltage_data(adc, data_volt, sdam_index);
+	if (ret)
+		goto unlock;
+
+	val = BIT(0);
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_EOC_CLR, &val, 1);
+	if (ret)
+		goto unlock;
+
+	/* To indicate conversion request is only to clear a status */
+	val = 0;
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
+	if (ret)
+		goto unlock;
+
+	val = ADC5_GEN3_CONV_REQ_REQ;
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
+
+unlock:
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
+static int get_sdam_from_irq(struct adc5_chip *adc, int irq)
+{
+	int i;
+
+	for (i = 0; i < adc->num_sdams; i++) {
+		if (adc->base[i].irq == irq)
+			return i;
+	}
+	return -ENOENT;
+}
+
+static irqreturn_t adc5_gen3_isr(int irq, void *dev_id)
+{
+	struct adc5_chip *adc = dev_id;
+	u8 status, tm_status[2], eoc_status, val;
+	int ret, sdam_num;
+
+	sdam_num = get_sdam_from_irq(adc, irq);
+	if (sdam_num < 0) {
+		dev_err(adc->dev, "adc irq %d not associated with an sdam\n", irq);
+		return IRQ_HANDLED;
+	}
+
+	ret = adc5_gen3_read(adc, sdam_num, ADC5_GEN3_STATUS1, &status, 1);
+	if (ret) {
+		dev_err(adc->dev, "adc read status1 failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	ret = adc5_gen3_read(adc, sdam_num, ADC5_GEN3_EOC_STS, &eoc_status, 1);
+	if (ret) {
+		dev_err(adc->dev, "adc read eoc status failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	if (status & ADC5_GEN3_STATUS1_CONV_FAULT) {
+		dev_err_ratelimited(adc->dev, "Unexpected conversion fault, status:%#x, eoc_status:%#x\n",
+				status, eoc_status);
+		val = ADC5_GEN3_CONV_ERR_CLR_REQ;
+		ret = adc5_gen3_write(adc, sdam_num, ADC5_GEN3_CONV_ERR_CLR, &val, 1);
+		if (ret < 0)
+			return IRQ_HANDLED;
+
+		/* To indicate conversion request is only to clear a status */
+		val = 0;
+		ret = adc5_gen3_write(adc, sdam_num, ADC5_GEN3_PERPH_CH, &val, 1);
+		if (ret < 0)
+			return IRQ_HANDLED;
+
+		val = ADC5_GEN3_CONV_REQ_REQ;
+		ret = adc5_gen3_write(adc, sdam_num, ADC5_GEN3_CONV_REQ, &val, 1);
+
+		return IRQ_HANDLED;
+	}
+
+	/* CHAN0 is the preconfigured channel for immediate conversion */
+	if (eoc_status & ADC5_GEN3_EOC_CHAN_0)
+		complete(&adc->complete);
+
+	ret = adc5_gen3_read(adc, sdam_num, ADC5_GEN3_TM_HIGH_STS, tm_status, 2);
+	if (ret) {
+		dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	if (tm_status[0] || tm_status[1])
+		schedule_work(&adc->tm_handler_work);
+
+	dev_dbg(adc->dev, "Interrupt status:%#x, EOC status:%#x, high:%#x, low:%#x\n",
+			status, eoc_status, tm_status[0], tm_status[1]);
+
+	return IRQ_HANDLED;
+}
+
+static void tm_handler_work(struct work_struct *work)
+{
+	struct adc5_chip *adc = container_of(work, struct adc5_chip, tm_handler_work);
+	struct adc5_channel_prop *chan_prop;
+	u8 tm_status[2] = {0};
+	u8 buf[16] = {0};
+	u8 val;
+	int ret, i, sdam_index = -1;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		bool upper_set = false, lower_set = false;
+		int temp, offset;
+		u16 code = 0;
+
+		chan_prop = &adc->chan_props[i];
+		offset = chan_prop->tm_chan_index;
+
+		if (!chan_prop->adc_tm)
+			continue;
+
+		mutex_lock(&adc->lock);
+		if (chan_prop->sdam_index != sdam_index) {
+			sdam_index = chan_prop->sdam_index;
+			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS,
+					tm_status, 2);
+			if (ret) {
+				dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
+				goto out;
+			}
+
+			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS_CLR,
+					tm_status, 2);
+			if (ret) {
+				dev_err(adc->dev, "adc write TM status failed with %d\n", ret);
+				goto out;
+			}
+
+			/* To indicate conversion request is only to clear a status */
+			val = 0;
+			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
+			if (ret) {
+				dev_err(adc->dev, "adc write status clear conv_req failed with %d\n",
+						ret);
+				goto out;
+			}
+
+			val = ADC5_GEN3_CONV_REQ_REQ;
+			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
+			if (ret) {
+				dev_err(adc->dev, "adc write conv_req failed with %d\n", ret);
+				goto out;
+			}
+
+			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CH_DATA0(0), buf,
+					sizeof(buf));
+			if (ret < 0) {
+				dev_err(adc->dev, "adc read data failed with %d\n", ret);
+				goto out;
+			}
+		}
+
+		if ((tm_status[0] & BIT(offset)) && (chan_prop->high_thr_en))
+			upper_set = true;
+
+		if ((tm_status[1] & BIT(offset)) && (chan_prop->low_thr_en))
+			lower_set = true;
+
+		mutex_unlock(&adc->lock);
+
+		if (!(upper_set || lower_set))
+			continue;
+
+		code = get_unaligned_le16(&buf[2 * offset]);
+		pr_debug("ADC_TM threshold code:%#x\n", code);
+
+		ret = qcom_adc5_hw_scale(chan_prop->scale_fn_type,
+			chan_prop->prescale, adc->data, code, &temp);
+		if (ret) {
+			dev_err(adc->dev, "Invalid temperature reading, ret = %d, code=%#x\n",
+					ret, code);
+			continue;
+		}
+
+		chan_prop->last_temp = temp;
+		chan_prop->last_temp_set = true;
+		thermal_zone_device_update(chan_prop->tzd, THERMAL_TRIP_VIOLATED);
+	}
+
+	return;
+
+out:
+	mutex_unlock(&adc->lock);
+}
+
+static int adc5_gen3_fwnode_xlate(struct iio_dev *indio_dev,
+				const struct fwnode_reference_args *iiospec)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	int i, v_channel;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		v_channel = V_CHAN(adc->chan_props[i]);
+		if (v_channel == iiospec->args[0])
+			return i;
+	}
+
+	return -ENOENT;
+}
+
+static int adc5_gen3_read_raw(struct iio_dev *indio_dev,
+			 struct iio_chan_spec const *chan, int *val, int *val2,
+			 long mask)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	struct adc5_channel_prop *prop;
+	u16 adc_code_volt;
+	int ret;
+
+	prop = &adc->chan_props[chan->address];
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = adc5_gen3_do_conversion(adc, prop,
+					&adc_code_volt);
+		if (ret)
+			return ret;
+
+		ret = qcom_adc5_hw_scale(prop->scale_fn_type,
+			prop->prescale, adc->data,
+			adc_code_volt, val);
+		if (ret)
+			return ret;
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_RAW:
+		ret = adc5_gen3_do_conversion(adc, prop,
+					&adc_code_volt);
+		if (ret)
+			return ret;
+		*val = (int)adc_code_volt;
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int adc5_gen3_read_label(struct iio_dev *indio_dev,
+			const struct iio_chan_spec *chan, char *label)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	struct adc5_channel_prop *prop;
+
+	prop = &adc->chan_props[chan->address];
+	return sprintf(label, "%s\n", prop->label);
+}
+
+static const struct iio_info adc5_gen3_info = {
+	.read_raw = adc5_gen3_read_raw,
+	.read_label = adc5_gen3_read_label,
+	.fwnode_xlate = adc5_gen3_fwnode_xlate,
+};
+
+static int adc_tm_gen3_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+	struct adc5_channel_prop *prop = tz->devdata;
+	struct adc5_chip *adc;
+	u16 adc_code_volt;
+	int ret;
+
+	if (!prop || !prop->chip)
+		return -EINVAL;
+
+	adc = prop->chip;
+
+	if (prop->last_temp_set) {
+		pr_debug("last_temp: %d\n", prop->last_temp);
+		prop->last_temp_set = false;
+		*temp = prop->last_temp;
+		return 0;
+	}
+
+	ret = adc5_gen3_do_conversion(adc, prop, &adc_code_volt);
+	if (ret < 0)
+		return ret;
+
+	return qcom_adc5_hw_scale(prop->scale_fn_type,
+		prop->prescale, adc->data,
+		adc_code_volt, temp);
+}
+
+static int _adc_tm5_gen3_disable_channel(struct adc5_channel_prop *prop)
+{
+	struct adc5_chip *adc = prop->chip;
+	int ret;
+	u8 val;
+
+	prop->high_thr_en = false;
+	prop->low_thr_en = false;
+
+	val = MEAS_INT_DISABLE;
+	ret = adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_TIMER_SEL, &val, 1);
+	if (ret)
+		return ret;
+
+	/* To indicate there is an actual conversion request */
+	val = ADC5_GEN3_CHAN_CONV_REQ | prop->tm_chan_index;
+	ret = adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
+	if (ret)
+		return ret;
+
+	val = ADC5_GEN3_CONV_REQ_REQ;
+	return adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
+}
+
+static int adc_tm5_gen3_disable_channel(struct adc5_channel_prop *prop)
+{
+	return _adc_tm5_gen3_disable_channel(prop);
+}
+
+# define ADC_TM5_GEN3_CONFIG_REGS 12
+
+static int adc_tm5_gen3_configure(struct adc5_channel_prop *prop,
+					int low_temp, int high_temp)
+{
+	struct adc5_chip *adc = prop->chip;
+	u8 conv_req = 0, buf[ADC_TM5_GEN3_CONFIG_REGS];
+	u16 adc_code;
+	int ret;
+
+	ret = adc5_gen3_poll_wait_hs(adc, prop->sdam_index);
+	if (ret < 0)
+		return ret;
+
+	ret = adc5_gen3_read(adc, prop->sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	/* Write SID */
+	buf[0] = FIELD_PREP(ADC5_GEN3_SID_MASK, prop->sid);
+
+	/*
+	 * Select TM channel and indicate there is an actual
+	 * conversion request
+	 */
+	buf[1] = ADC5_GEN3_CHAN_CONV_REQ | prop->tm_chan_index;
+
+	buf[2] = prop->timer;
+
+	/* Digital param selection */
+	adc5_gen3_update_dig_param(adc, prop, &buf[3]);
+
+	/* Update fast average sample value */
+	buf[4] &= ~ADC5_GEN3_FAST_AVG_CTL_SAMPLES_MASK;
+	buf[4] |= prop->avg_samples | ADC5_GEN3_FAST_AVG_CTL_EN;
+
+	/* Select ADC channel */
+	buf[5] = prop->channel;
+
+	/* Select HW settle delay for channel */
+	buf[6] = FIELD_PREP(ADC5_GEN3_HW_SETTLE_DELAY_MASK, prop->hw_settle_time);
+
+	/* High temperature corresponds to low voltage threshold */
+	if (high_temp != INT_MAX) {
+		prop->low_thr_en = true;
+		adc_code = qcom_adc_tm5_gen2_temp_res_scale(high_temp);
+		put_unaligned_le16(adc_code, &buf[8]);
+	} else {
+		prop->low_thr_en = false;
+	}
+
+	/* Low temperature corresponds to high voltage threshold */
+	if (low_temp != -INT_MAX) {
+		prop->high_thr_en = true;
+		adc_code = qcom_adc_tm5_gen2_temp_res_scale(low_temp);
+		put_unaligned_le16(adc_code, &buf[10]);
+	} else {
+		prop->high_thr_en = false;
+	}
+
+	buf[7] = 0;
+	if (prop->high_thr_en)
+		buf[7] |= ADC5_GEN3_HIGH_THR_INT_EN;
+	if (prop->low_thr_en)
+		buf[7] |= ADC5_GEN3_LOW_THR_INT_EN;
+
+	ret = adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	conv_req = ADC5_GEN3_CONV_REQ_REQ;
+	return adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_CONV_REQ, &conv_req, 1);
+}
+
+static int adc_tm5_gen3_set_trip_temp(struct thermal_zone_device *tz,
+					int low_temp, int high_temp)
+{
+	struct adc5_channel_prop *prop = tz->devdata;
+	struct adc5_chip *adc;
+	int ret;
+
+	if (!prop || !prop->chip)
+		return -EINVAL;
+
+	adc = prop->chip;
+
+	dev_dbg(adc->dev, "channel:%s, low_temp(mdegC):%d, high_temp(mdegC):%d\n",
+		prop->label, low_temp, high_temp);
+
+	mutex_lock(&adc->lock);
+	if (high_temp == INT_MAX && low_temp <= -INT_MAX)
+		ret = adc_tm5_gen3_disable_channel(prop);
+	else
+		ret = adc_tm5_gen3_configure(prop, low_temp, high_temp);
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
+static const struct thermal_zone_device_ops adc_tm_ops = {
+	.get_temp = adc_tm_gen3_get_temp,
+	.set_trips = adc_tm5_gen3_set_trip_temp,
+};
+
+static int adc_tm_register_tzd(struct adc5_chip *adc)
+{
+	unsigned int i, channel;
+	struct thermal_zone_device *tzd;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		channel = V_CHAN(adc->chan_props[i]);
+
+		if (!adc->chan_props[i].adc_tm)
+			continue;
+		tzd = devm_thermal_of_zone_register(adc->dev, channel,
+			&adc->chan_props[i], &adc_tm_ops);
+
+		if (IS_ERR(tzd)) {
+			if (PTR_ERR(tzd) == -ENODEV) {
+				dev_warn(adc->dev, "thermal sensor on channel %d is not used\n",
+					 channel);
+				continue;
+			}
+
+			dev_err(adc->dev, "Error registering TZ zone:%ld for channel:%d\n",
+				PTR_ERR(tzd), adc->chan_props[i].channel);
+			return PTR_ERR(tzd);
+		}
+		adc->chan_props[i].tzd = tzd;
+	}
+
+	return 0;
+}
+
+static void adc5_gen3_disable(void *data)
+{
+	struct adc5_chip *adc = data;
+	int i;
+
+	if (adc->n_tm_channels)
+		cancel_work_sync(&adc->tm_handler_work);
+
+	for (i = 0; i < adc->num_sdams; i++)
+		free_irq(adc->base[i].irq, adc);
+
+	mutex_lock(&adc->lock);
+	/* Disable all available TM channels */
+	for (i = 0; i < adc->nchannels; i++) {
+		if (!adc->chan_props[i].adc_tm)
+			continue;
+		adc5_gen3_poll_wait_hs(adc, adc->chan_props[i].sdam_index);
+		_adc_tm5_gen3_disable_channel(&adc->chan_props[i]);
+	}
+
+	mutex_unlock(&adc->lock);
+}
+
+struct adc5_channels {
+	unsigned int prescale_index;
+	enum iio_chan_type type;
+	long info_mask;
+	enum vadc_scale_fn_type scale_fn_type;
+};
+
+/* In these definitions, _pre refers to an index into adc5_prescale_ratios. */
+#define ADC5_CHAN(_type, _mask, _pre, _scale)	\
+	{						\
+		.prescale_index = _pre,			\
+		.type = _type,				\
+		.info_mask = _mask,			\
+		.scale_fn_type = _scale,		\
+	},						\
+
+#define ADC5_CHAN_TEMP(_pre, _scale)		\
+	ADC5_CHAN(IIO_TEMP, BIT(IIO_CHAN_INFO_PROCESSED), _pre, _scale)	\
+
+#define ADC5_CHAN_VOLT(_pre, _scale)		\
+	ADC5_CHAN(IIO_VOLTAGE, BIT(IIO_CHAN_INFO_PROCESSED), _pre, _scale)	\
+
+#define ADC5_CHAN_CUR(_pre, _scale)		\
+	ADC5_CHAN(IIO_CURRENT, BIT(IIO_CHAN_INFO_PROCESSED), _pre, _scale)	\
+
+static const struct adc5_channels adc5_gen3_chans_pmic[ADC5_MAX_CHANNEL] = {
+	[ADC5_GEN3_REF_GND]		= ADC5_CHAN_VOLT(0, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_1P25VREF]		= ADC5_CHAN_VOLT(0, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_VPH_PWR]		= ADC5_CHAN_VOLT(1, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_VBAT_SNS_QBG]	= ADC5_CHAN_VOLT(1, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_USB_SNS_V_16]	= ADC5_CHAN_TEMP(8, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_VIN_DIV16_MUX]	= ADC5_CHAN_TEMP(8, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_DIE_TEMP]		= ADC5_CHAN_TEMP(0,
+						SCALE_HW_CALIB_PMIC_THERM_PM7)
+	[ADC5_GEN3_TEMP_ALARM_LITE]	= ADC5_CHAN_TEMP(0,
+						SCALE_HW_CALIB_PMIC_THERM_PM7)
+	[ADC5_GEN3_AMUX1_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX2_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX3_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX4_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX5_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX6_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX1_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX2_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX3_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX4_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+};
+
+static int adc5_gen3_get_fw_channel_data(struct adc5_chip *adc,
+				    struct adc5_channel_prop *prop,
+				    struct fwnode_handle *fwnode,
+				    const struct adc5_data *data)
+{
+	const char *name = fwnode_get_name(fwnode);
+	const char *channel_name;
+	struct device *dev = adc->dev;
+	u32 chan, value, varr[2], sid = 0;
+	int ret, val;
+
+	ret = fwnode_property_read_u32(fwnode, "reg", &chan);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "invalid channel number %s\n", name);
+
+	/*
+	 * Value read from "reg" is virtual channel number
+	 * virtual channel number = sid << 8 | channel number
+	 */
+
+	sid = FIELD_GET(ADC5_GEN3_VIRTUAL_SID_MASK, chan);
+	chan = FIELD_GET(ADC5_GEN3_CHANNEL_MASK, chan);
+
+	if (chan > ADC5_GEN3_OFFSET_EXT2)
+		return dev_err_probe(dev, -EINVAL, "%s invalid channel number %d\n", name, chan);
+
+	prop->channel = chan;
+	prop->sid = sid;
+
+	ret = fwnode_property_read_string(fwnode, "label", &channel_name);
+	if (ret)
+		channel_name = name;
+	prop->label = channel_name;
+
+	prop->decimation = ADC5_DECIMATION_DEFAULT;
+	ret = fwnode_property_read_u32(fwnode, "qcom,decimation", &value);
+	if (!ret) {
+		ret = qcom_adc5_decimation_from_dt(value, data->decimation);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid decimation %d\n",
+				chan, value);
+		prop->decimation = ret;
+	}
+
+	prop->prescale = adc->data->adc_chans[prop->channel].prescale_index;
+	ret = fwnode_property_read_u32_array(fwnode, "qcom,pre-scaling", varr, 2);
+	if (!ret) {
+		ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid pre-scaling <%d %d>\n",
+				chan, varr[0], varr[1]);
+		prop->prescale = ret;
+	}
+
+	prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
+	ret = fwnode_property_read_u32(fwnode, "qcom,hw-settle-time", &value);
+	if (!ret) {
+		ret = qcom_adc5_hw_settle_time_from_dt(value,
+						data->hw_settle_1);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid hw-settle-time %d us\n",
+				chan, value);
+		prop->hw_settle_time = ret;
+	}
+
+	prop->avg_samples = VADC_DEF_AVG_SAMPLES;
+	ret = fwnode_property_read_u32(fwnode, "qcom,avg-samples", &value);
+	if (!ret) {
+		ret = qcom_adc5_avg_samples_from_dt(value);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid avg-samples %d\n",
+				chan, value);
+		prop->avg_samples = ret;
+	}
+
+	if (fwnode_property_read_bool(fwnode, "qcom,ratiometric"))
+		prop->cal_method = ADC5_RATIOMETRIC_CAL;
+	else
+		prop->cal_method = ADC5_ABSOLUTE_CAL;
+
+	prop->timer = MEAS_INT_IMMEDIATE;
+
+	prop->adc_tm = fwnode_property_read_bool(fwnode, "qcom,adc-tm");
+
+	if (prop->adc_tm) {
+		adc->n_tm_channels++;
+		if (adc->n_tm_channels > ((adc->num_sdams * 8) - 1))
+			return dev_err_probe(adc->dev, -EINVAL,
+				"Number of TM nodes %u greater than channels supported:%u\n",
+				adc->n_tm_channels, (adc->num_sdams * 8) - 1);
+
+		val = adc->n_tm_channels / 8;
+		prop->sdam_index = val;
+		prop->tm_chan_index = adc->n_tm_channels - (8*val);
+
+		prop->timer = MEAS_INT_1S;
+	}
+
+	return 0;
+}
+
+static const struct adc5_data adc5_gen3_data_pmic = {
+	.full_scale_code_volt = 0x70e4,
+	.adc_chans = adc5_gen3_chans_pmic,
+	.info = &adc5_gen3_info,
+	.decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
+				{85, 340, 1360},
+	.hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
+				{15, 100, 200, 300, 400, 500, 600, 700,
+				1000, 2000, 4000, 8000, 16000, 32000,
+				64000, 128000},
+};
+
+static const struct of_device_id adc5_match_table[] = {
+	{
+		.compatible = "qcom,spmi-adc5-gen3",
+		.data = &adc5_gen3_data_pmic,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, adc5_match_table);
+
+static int adc5_get_fw_data(struct adc5_chip *adc)
+{
+	const struct adc5_channels *adc_chan;
+	struct iio_chan_spec *iio_chan;
+	struct adc5_channel_prop *chan_props;
+	struct fwnode_handle *child;
+	unsigned int index = 0;
+	int ret;
+
+	adc->nchannels = device_get_child_node_count(adc->dev);
+	if (!adc->nchannels)
+		return -EINVAL;
+
+	adc->iio_chans = devm_kcalloc(adc->dev, adc->nchannels,
+				       sizeof(*adc->iio_chans), GFP_KERNEL);
+	if (!adc->iio_chans)
+		return -ENOMEM;
+
+	adc->chan_props = devm_kcalloc(adc->dev, adc->nchannels,
+					sizeof(*adc->chan_props), GFP_KERNEL);
+	if (!adc->chan_props)
+		return -ENOMEM;
+
+	chan_props = adc->chan_props;
+	adc->n_tm_channels = 0;
+	iio_chan = adc->iio_chans;
+	adc->data = device_get_match_data(adc->dev);
+	if (!adc->data)
+		adc->data = &adc5_gen3_data_pmic;
+
+	device_for_each_child_node(adc->dev, child) {
+		ret = adc5_gen3_get_fw_channel_data(adc, chan_props, child, adc->data);
+		if (ret < 0) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		chan_props->chip = adc;
+		chan_props->scale_fn_type =
+			adc->data->adc_chans[chan_props->channel].scale_fn_type;
+		adc_chan = &adc->data->adc_chans[chan_props->channel];
+		iio_chan->channel = V_CHAN(*chan_props);
+		iio_chan->info_mask_separate = adc_chan->info_mask;
+		iio_chan->type = adc_chan->type;
+		iio_chan->address = index;
+		iio_chan->indexed = 1;
+		iio_chan++;
+		chan_props++;
+		index++;
+	}
+
+	return 0;
+}
+
+static int adc5_gen3_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct iio_dev *indio_dev;
+	struct adc5_chip *adc;
+	struct regmap *regmap;
+	int ret, i;
+	u32 *reg;
+
+	regmap = dev_get_regmap(dev->parent, NULL);
+	if (!regmap)
+		return -ENODEV;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	adc = iio_priv(indio_dev);
+	adc->regmap = regmap;
+	adc->dev = dev;
+
+	ret = device_property_count_u32(dev, "reg");
+	if (ret < 0)
+		return ret;
+
+	adc->num_sdams = ret;
+
+	reg = kcalloc(adc->num_sdams, sizeof(u32), GFP_KERNEL);
+	if (!reg)
+		return -ENOMEM;
+
+	ret = device_property_read_u32_array(dev, "reg", reg, adc->num_sdams);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to read reg property, ret = %d\n", ret);
+
+	adc->base = devm_kcalloc(dev, adc->num_sdams, sizeof(*adc->base), GFP_KERNEL);
+	if (!adc->base)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, indio_dev);
+	init_completion(&adc->complete);
+	mutex_init(&adc->lock);
+
+	for (i = 0; i < adc->num_sdams; i++) {
+		adc->base[i].base_addr = reg[i];
+
+		adc->base[i].irq_name = devm_kasprintf(dev, GFP_KERNEL, "adc-sdam%d", i);
+		if (!adc->base[i].irq_name) {
+			kfree(reg);
+			ret = -ENOMEM;
+			goto err_irq;
+		}
+
+		ret = platform_get_irq_byname(pdev, adc->base[i].irq_name);
+		if (ret < 0) {
+			kfree(reg);
+			dev_err(dev, "Getting IRQ %d by name failed, ret = %d\n",
+					adc->base[i].irq, ret);
+			goto err_irq;
+		}
+		adc->base[i].irq = ret;
+
+		ret = request_irq(adc->base[i].irq, adc5_gen3_isr, 0, adc->base[i].irq_name, adc);
+		if (ret < 0) {
+			kfree(reg);
+			dev_err(dev, "Failed to request SDAM%d irq, ret = %d\n", i, ret);
+			goto err_irq;
+		}
+	}
+	kfree(reg);
+
+	ret = devm_add_action(dev, adc5_gen3_disable, adc);
+	if (ret < 0) {
+		dev_err(dev, "failed to register adc disablement devm action, %d\n", ret);
+		goto err_irq;
+	}
+
+	ret = adc5_get_fw_data(adc);
+	if (ret < 0) {
+		dev_err(dev, "adc get dt data failed, ret = %d\n", ret);
+		goto err_irq;
+	}
+
+	ret = adc_tm_register_tzd(adc);
+	if (ret < 0)
+		goto err_irq;
+
+	if (adc->n_tm_channels)
+		INIT_WORK(&adc->tm_handler_work, tm_handler_work);
+
+	indio_dev->name = pdev->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &adc5_gen3_info;
+	indio_dev->channels = adc->iio_chans;
+	indio_dev->num_channels = adc->nchannels;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (!ret)
+		return 0;
+
+err_irq:
+	for (i = 0; i < adc->num_sdams; i++)
+		free_irq(adc->base[i].irq, adc);
+
+	return ret;
+}
+
+static struct platform_driver adc5_gen3_driver = {
+	.driver = {
+		.name = "qcom-spmi-adc5-gen3",
+		.of_match_table = adc5_match_table,
+	},
+	.probe = adc5_gen3_probe,
+};
+module_platform_driver(adc5_gen3_driver);
+
+MODULE_DESCRIPTION("Qualcomm Technologies Inc. PMIC5 Gen3 ADC driver");
+MODULE_LICENSE("GPL");