@@ -20776,6 +20776,13 @@ S: Maintained
F: drivers/reset/starfive/reset-starfive-jh81*
F: include/dt-bindings/reset/starfive?jh81*.h
+STARFIVE JH8100 PINCTRL DRIVERS
+M: Alex Soo <yuklin.soo@starfivetech.com>
+S: Supported
+F: Documentation/devicetree/bindings/pinctrl/starfive,jh81*.yaml
+F: drivers/pinctrl/starfive/pinctrl-starfive-jh81*
+F: include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
+
STATIC BRANCH/CALL
M: Peter Zijlstra <peterz@infradead.org>
M: Josh Poimboeuf <jpoimboe@kernel.org>
@@ -94,3 +94,15 @@ config PINCTRL_STARFIVE_JH8100_SYS_GMAC
This also provides a syscon interface to configure the GMAC1 voltage level for RGMII(1.8V
2.5V), GMII(2.5V/3.3V), to configure the SDIO1 voltage level to support the 3.3/1.8V voltage
switching in high-speed mode, and configure the GMAC1 network interface and timing (slew rate).
+
+config PINCTRL_STARFIVE_JH8100_AON
+ tristate "Always-on pinctrl and GPIO driver for the StarFive JH8100 SoC"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JH8100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support always-on pin control on the StarFive JH8100 SoC.
+ This also provides a syscon interface to configure the GMAC0 voltage level for RGMII(1.8V
+ 2.5V), GMII(2.5V/3.3V), to configure the SDIO0 voltage level to support the 3.3/1.8V voltage
+ switching in high-speed mode, and configure the GMAC0 network interface and timing (slew rate).
@@ -10,3 +10,4 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH8100) += pinctrl-starfive-jh8100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH8100_SYS_EAST) += pinctrl-starfive-jh8100-sys-east.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH8100_SYS_WEST) += pinctrl-starfive-jh8100-sys-west.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH8100_SYS_GMAC) += pinctrl-starfive-jh8100-sys-gmac.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JH8100_AON) += pinctrl-starfive-jh8100-aon.o
new file mode 100644
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JH8100 SoC aon controller
+ *
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <linux/bits.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/pinctrl/starfive,jh8100-pinctrl.h>
+
+#include "../core.h"
+#include "../pinconf.h"
+#include "../pinmux.h"
+#include "pinctrl-starfive-jh8100.h"
+
+#define JH8100_AON_NGPIO 16
+#define JH8100_AON_GC_BASE 64
+
+/* registers */
+#define JH8100_AON_DOEN 0x00
+#define JH8100_AON_DOUT 0x10
+#define JH8100_AON_GPI 0x20
+#define JH8100_AON_GPIOIN 0x54
+
+#define JH8100_AON_GPIOEN 0x34
+#define JH8100_AON_GPIOIS 0x38
+#define JH8100_AON_GPIOIC 0x3c
+#define JH8100_AON_GPIOIBE 0x40
+#define JH8100_AON_GPIOIEV 0x44
+#define JH8100_AON_GPIOIE 0x48
+#define JH8100_AON_GPIORIS 0x4c
+#define JH8100_AON_GPIOMIS 0x50
+
+#define JH8100_AON_GPO_PDA_0_14_CFG 0x90
+
+static const struct pinctrl_pin_desc jh8100_aon_pins[] = {
+ PINCTRL_PIN(PAD_RGPIO0, "AON_RGPIO0"),
+ PINCTRL_PIN(PAD_RGPIO1, "AON_RGPIO1"),
+ PINCTRL_PIN(PAD_RGPIO2, "AON_RGPIO2"),
+ PINCTRL_PIN(PAD_RGPIO3, "AON_RGPIO3"),
+ PINCTRL_PIN(PAD_RGPIO4, "AON_RGPIO4"),
+ PINCTRL_PIN(PAD_RGPIO5, "AON_RGPIO5"),
+ PINCTRL_PIN(PAD_RGPIO6, "AON_RGPIO6"),
+ PINCTRL_PIN(PAD_RGPIO7, "AON_RGPIO7"),
+ PINCTRL_PIN(PAD_RGPIO8, "AON_RGPIO8"),
+ PINCTRL_PIN(PAD_RGPIO9, "AON_RGPIO9"),
+ PINCTRL_PIN(PAD_RGPIO10, "AON_RGPIO10"),
+ PINCTRL_PIN(PAD_RGPIO11, "AON_RGPIO11"),
+ PINCTRL_PIN(PAD_RGPIO12, "AON_RGPIO12"),
+ PINCTRL_PIN(PAD_RGPIO13, "AON_RGPIO13"),
+ PINCTRL_PIN(PAD_RGPIO14, "AON_RGPIO14"),
+ PINCTRL_PIN(PAD_RGPIO15, "AON_RGPIO15"),
+ PINCTRL_PIN(PAD_TESTEN, "AON_TESTEN"),
+ PINCTRL_PIN(PAD_RSTN, "AON_RSTN"),
+ PINCTRL_PIN(PAD_OSCK_XIN, "AON_OSCK_XIN"),
+ PINCTRL_PIN(PAD_OSCK_XOUT, "AON_OSCK_XOUT"),
+ PINCTRL_PIN(PAD_OSCM_XIN, "AON_OSCM_XIN"),
+ PINCTRL_PIN(PAD_OSCM_XOUT, "AON_OSCM_XOUT"),
+ PINCTRL_PIN(PAD_GMAC0_MDC, "AON_GMAC0_MDC"),
+ PINCTRL_PIN(PAD_GMAC0_MDIO, "AON_GMAC0_MDIO"),
+ PINCTRL_PIN(PAD_GMAC0_RXD0, "AON_GMAC0_RXD0"),
+ PINCTRL_PIN(PAD_GMAC0_RXD1, "AON_GMAC0_RXD1"),
+ PINCTRL_PIN(PAD_GMAC0_RXD2, "AON_GMAC0_RXD2"),
+ PINCTRL_PIN(PAD_GMAC0_RXD3, "AON_GMAC0_RXD3"),
+ PINCTRL_PIN(PAD_GMAC0_RXDV, "AON_GMAC0_RXDV"),
+ PINCTRL_PIN(PAD_GMAC0_RXC, "AON_GMAC0_RXC"),
+ PINCTRL_PIN(PAD_GMAC0_TXD0, "AON_GMAC0_TXD0"),
+ PINCTRL_PIN(PAD_GMAC0_TXD1, "AON_GMAC0_TXD1"),
+ PINCTRL_PIN(PAD_GMAC0_TXD2, "AON_GMAC0_TXD2"),
+ PINCTRL_PIN(PAD_GMAC0_TXD3, "AON_GMAC0_TXD3"),
+ PINCTRL_PIN(PAD_GMAC0_TXEN, "AON_GMAC0_TXEN"),
+ PINCTRL_PIN(PAD_GMAC0_TXC, "AON_GMAC0_TXC"),
+};
+
+static int jh8100_aon_set_one_pin_mux(struct jh8100_pinctrl *sfp,
+ unsigned int pin,
+ unsigned int din, u32 dout,
+ u32 doen, u32 func)
+{
+ if (pin < sfp->gc.ngpio && func == 0)
+ jh8100_set_gpiomux(sfp, pin, din, dout, doen);
+
+ return 0;
+}
+
+static int jh8100_aon_get_padcfg_base(struct jh8100_pinctrl *sfp,
+ unsigned int pin)
+{
+ if (pin < PAD_GMAC0_MDC)
+ return JH8100_AON_GPO_PDA_0_14_CFG;
+
+ return -1;
+}
+
+static void jh8100_aon_irq_handler(struct irq_desc *desc)
+{
+ struct jh8100_pinctrl *sfp = jh8100_from_irq_desc(desc);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+ unsigned long mis;
+ unsigned int pin;
+
+ chained_irq_enter(chip, desc);
+
+ mis = readl_relaxed(sfp->base + JH8100_AON_GPIOMIS);
+ for_each_set_bit(pin, &mis, JH8100_AON_NGPIO)
+ generic_handle_domain_irq(sfp->gc.irq.domain, pin);
+
+ chained_irq_exit(chip, desc);
+}
+
+static int jh8100_aon_init_hw(struct gpio_chip *gc)
+{
+ struct jh8100_pinctrl *sfp = container_of(gc,
+ struct jh8100_pinctrl, gc);
+
+ /* mask all GPIO interrupts */
+ writel_relaxed(0, sfp->base + JH8100_AON_GPIOIE);
+ /* clear edge interrupt flags */
+ writel_relaxed(0, sfp->base + JH8100_AON_GPIOIC);
+ writel_relaxed(0x0fff, sfp->base + JH8100_AON_GPIOIC);
+ /* enable GPIO interrupts */
+ writel_relaxed(1, sfp->base + JH8100_AON_GPIOEN);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int jh8100_aon_pinctrl_suspend(struct device *dev)
+{
+ struct jh8100_pinctrl *sfp;
+ int i;
+
+ sfp = dev_get_drvdata(dev);
+ if (!sfp)
+ return -EINVAL;
+
+ if (device_may_wakeup(dev))
+ enable_irq_wake(sfp->wakeup_irq);
+
+ for (i = 0; i < JH8100_AON_REG_NUM; i++)
+ sfp->jh8100_aon_regs[i] = readl_relaxed(sfp->base + (i * 4));
+
+ return pinctrl_force_sleep(sfp->pctl);
+}
+
+static int jh8100_aon_pinctrl_resume(struct device *dev)
+{
+ struct jh8100_pinctrl *sfp;
+ int i;
+
+ sfp = dev_get_drvdata(dev);
+ if (!sfp)
+ return -EINVAL;
+
+ if (device_may_wakeup(dev))
+ disable_irq_wake(sfp->wakeup_irq);
+
+ for (i = 0; i < JH8100_AON_REG_NUM; i++)
+ writel_relaxed(sfp->jh8100_aon_regs[i], sfp->base + (i * 4));
+
+ return pinctrl_force_default(sfp->pctl);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(jh8100_aon_pinctrl_dev_pm_ops,
+ jh8100_aon_pinctrl_suspend,
+ jh8100_aon_pinctrl_resume);
+
+static const struct jh8100_gpio_irq_reg jh8100_aon_irq_reg = {
+ .is_reg_base = JH8100_AON_GPIOIS,
+ .ic_reg_base = JH8100_AON_GPIOIC,
+ .ibe_reg_base = JH8100_AON_GPIOIBE,
+ .iev_reg_base = JH8100_AON_GPIOIEV,
+ .ie_reg_base = JH8100_AON_GPIOIE,
+ .ris_reg_base = JH8100_AON_GPIORIS,
+ .mis_reg_base = JH8100_AON_GPIOMIS,
+};
+
+static const struct jh8100_pinctrl_soc_info jh8100_aon_pinctrl_info = {
+ .pins = jh8100_aon_pins,
+ .npins = ARRAY_SIZE(jh8100_aon_pins),
+ .ngpios = JH8100_AON_NGPIO,
+ .gc_base = JH8100_AON_GC_BASE,
+ .dout_reg_base = JH8100_AON_DOUT,
+ .dout_mask = GENMASK(4, 0),
+ .doen_reg_base = JH8100_AON_DOEN,
+ .doen_mask = GENMASK(2, 0),
+ .gpi_reg_base = JH8100_AON_GPI,
+ .gpi_mask = GENMASK(4, 0),
+ .gpioin_reg_base = JH8100_AON_GPIOIN,
+ .irq_reg = &jh8100_aon_irq_reg,
+ .jh8100_set_one_pin_mux = jh8100_aon_set_one_pin_mux,
+ .jh8100_get_padcfg_base = jh8100_aon_get_padcfg_base,
+ .jh8100_gpio_irq_handler = jh8100_aon_irq_handler,
+ .jh8100_gpio_init_hw = jh8100_aon_init_hw,
+};
+
+static const struct of_device_id jh8100_aon_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jh8100-aon-pinctrl",
+ .data = &jh8100_aon_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jh8100_aon_pinctrl_of_match);
+
+static struct platform_driver jh8100_aon_pinctrl_driver = {
+ .probe = jh8100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jh8100-aon-pinctrl",
+#ifdef CONFIG_PM_SLEEP
+ .pm = &jh8100_aon_pinctrl_dev_pm_ops,
+#endif
+ .of_match_table = jh8100_aon_pinctrl_of_match,
+ },
+};
+module_platform_driver(jh8100_aon_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for the StarFive JH8100 SoC aon controller");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL v2");
@@ -16,6 +16,7 @@
#define JH8100_SYS_WEST_REG_NUM 44
#define JH8100_SYS_EAST_REG_NUM 116
#define JH8100_SYS_GMAC_REG_NUM 19
+#define JH8100_AON_REG_NUM 65
struct jh8100_pinctrl {
struct device *dev;
@@ -30,6 +31,7 @@ struct jh8100_pinctrl {
unsigned int jh8100_sys_west_regs[JH8100_SYS_WEST_REG_NUM];
unsigned int jh8100_sys_east_regs[JH8100_SYS_EAST_REG_NUM];
unsigned int jh8100_sys_gmac_regs[JH8100_SYS_GMAC_REG_NUM];
+ unsigned int jh8100_aon_regs[JH8100_AON_REG_NUM];
/* wakeup */
int wakeup_gpio;
int wakeup_irq;