@@ -17,7 +17,7 @@
io-channel-names = "buttons";
keyup-threshold-microvolt = <1800000>;
- update-button {
+ button-update {
label = "update";
linux,code = <KEY_VENDOR>;
press-threshold-microvolt = <1300000>;
@@ -416,7 +416,7 @@
pinctrl-names = "default";
status = "okay";
- gd25lq128: spi-flash@0 {
+ gd25lq128: flash@0 {
compatible = "jedec,spi-nor";
#address-cells = <1>;
#size-cells = <1>;
@@ -49,6 +49,12 @@
no-map;
};
+ /* 32 MiB reserved for ARM Trusted Firmware (BL32) */
+ secmon_reserved_bl32: secmon@5300000 {
+ reg = <0x0 0x05300000 0x0 0x2000000>;
+ no-map;
+ };
+
linux,cma {
compatible = "shared-dma-pool";
reusable;
@@ -126,6 +132,7 @@
l2: l2-cache0 {
compatible = "cache";
+ cache-level = <2>;
};
};
@@ -226,7 +233,7 @@
reg = <0x14 0x10>;
};
- eth_mac: eth_mac@34 {
+ eth_mac: eth-mac@34 {
reg = <0x34 0x10>;
};
@@ -243,7 +250,7 @@
scpi_clocks: clocks {
compatible = "arm,scpi-clocks";
- scpi_dvfs: scpi_clocks@0 {
+ scpi_dvfs: clocks-0 {
compatible = "arm,scpi-dvfs-clocks";
#clock-cells = <1>;
clock-indices = <0>;
@@ -444,7 +451,7 @@
sysctrl_AO: sys-ctrl@0 {
compatible = "amlogic,meson-gx-ao-sysctrl", "simple-mfd", "syscon";
- reg = <0x0 0x0 0x0 0x100>;
+ reg = <0x0 0x0 0x0 0x100>;
clkc_AO: clock-controller {
compatible = "amlogic,meson-gx-aoclkc";
@@ -525,7 +532,7 @@
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
- hwrng: rng {
+ hwrng: rng@0 {
compatible = "amlogic,meson-rng";
reg = <0x0 0x0 0x0 0x4>;
};
@@ -596,21 +603,21 @@
sd_emmc_a: mmc@70000 {
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
reg = <0x0 0x70000 0x0 0x800>;
- interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
sd_emmc_b: mmc@72000 {
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
reg = <0x0 0x72000 0x0 0x800>;
- interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
sd_emmc_c: mmc@74000 {
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
reg = <0x0 0x74000 0x0 0x800>;
- interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
};
@@ -385,9 +385,20 @@
/* Bluetooth on AP6212 */
&uart_A {
- status = "disabled";
+ status = "okay";
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&wifi_32k>;
+ clock-names = "lpo";
+ vbat-supply = <&vddio_ao3v3>;
+ vddio-supply = <&vddio_ao18>;
+ host-wakeup-gpios = <&gpio GPIOX_21 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
+ };
};
/* 40-pin CON1 */
@@ -250,21 +250,6 @@
};
};
-&gpio_ao {
- /*
- * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
- * to be turned high in order to be detected by the USB Controller
- * This signal should be handled by a USB specific power sequence
- * in order to reset the Hub when USB bus is powered down.
- */
- hog-0 {
- gpio-hog;
- gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "usb-hub-reset";
- };
-};
-
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
@@ -414,5 +399,16 @@
};
&usb1 {
+ dr_mode = "host";
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "okay";
+
+ hub@1 {
+ /* Genesys Logic GL852G USB 2.0 hub */
+ compatible = "usb5e3,610";
+ reg = <1>;
+ vdd-supply = <&p5v0>;
+ reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+ };
};
@@ -300,8 +300,8 @@
};
&gpio_intc {
- compatible = "amlogic,meson-gpio-intc",
- "amlogic,meson-gxbb-gpio-intc";
+ compatible = "amlogic,meson-gxbb-gpio-intc",
+ "amlogic,meson-gpio-intc";
status = "okay";
};
@@ -427,6 +427,20 @@
};
};
+ spi_idle_high_pins: spi-idle-high-pins {
+ mux {
+ groups = "spi_sclk";
+ bias-pull-up;
+ };
+ };
+
+ spi_idle_low_pins: spi-idle-low-pins {
+ mux {
+ groups = "spi_sclk";
+ bias-pull-down;
+ };
+ };
+
spi_ss0_pins: spi-ss0 {
mux {
groups = "spi_ss0";
@@ -298,7 +298,7 @@
pinctrl-0 = <&nor_pins>;
pinctrl-names = "default";
- w25q32: spi-flash@0 {
+ w25q32: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
@@ -86,11 +86,11 @@
};
&efuse {
- bt_mac: bt_mac@6 {
+ bt_mac: bt-mac@6 {
reg = <0x6 0x6>;
};
- wifi_mac: wifi_mac@C {
+ wifi_mac: wifi-mac@c {
reg = <0xc 0x6>;
};
};
@@ -213,6 +213,12 @@
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
uart-has-rtscts;
+
+ bluetooth {
+ compatible = "realtek,rtl8822cs-bt";
+ enable-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ host-wake-gpios = <&gpio GPIOX_18 GPIO_ACTIVE_HIGH>;
+ };
};
&uart_C {
@@ -233,7 +239,7 @@
pinctrl-names = "default";
pinctrl-0 = <&i2c_b_pins>;
- pcf8563: pcf8563@51 {
+ pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
status = "okay";
@@ -140,7 +140,6 @@
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
- clock-frequency = <32768>;
clock-output-names = "xin32k";
};
};
@@ -218,20 +217,7 @@
};
&sd_emmc_a {
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-&uart_A {
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
- max-speed = <2000000>;
- clocks = <&wifi32k>;
- clock-names = "lpo";
- };
+ max-frequency = <100000000>;
};
/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */
@@ -284,7 +284,7 @@
pinctrl-0 = <&nor_pins>;
pinctrl-names = "default";
- nor_4u1: spi-flash@0 {
+ nor_4u1: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
@@ -305,7 +305,6 @@
};
&usb2_phy0 {
- pinctrl-names = "default";
phy-supply = <&vcc5v>;
};
@@ -7,11 +7,19 @@
/dts-v1/;
#include "meson-gxl-s905x-p212.dtsi"
+#include <dt-bindings/sound/meson-aiu.h>
/ {
compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl";
model = "Amlogic Meson GXL (S905X) P212 Development Board";
+ dio2133: analog-amplifier {
+ compatible = "simple-audio-amplifier";
+ sound-name-prefix = "AU2";
+ VCC-supply = <&hdmi_5v>;
+ enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ };
+
cvbs-connector {
compatible = "composite-video-connector";
@@ -32,6 +40,66 @@
};
};
};
+
+ sound {
+ compatible = "amlogic,gx-sound-card";
+ model = "S905X-P212";
+ audio-aux-devs = <&dio2133>;
+ audio-widgets = "Line", "Lineout";
+ audio-routing = "AU2 INL", "ACODEC LOLN",
+ "AU2 INR", "ACODEC LORN",
+ "Lineout", "AU2 OUTL",
+ "Lineout", "AU2 OUTR";
+ assigned-clocks = <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>,
+ <&clkc CLKID_MPLL2>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ dai-link-0 {
+ sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+ dai-format = "i2s";
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+ };
+
+ codec-1 {
+ sound-dai = <&aiu AIU_ACODEC CTRL_I2S>;
+ };
+ };
+
+ dai-link-2 {
+ sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+ codec-0 {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+
+ dai-link-3 {
+ sound-dai = <&aiu AIU_ACODEC CTRL_OUT>;
+
+ codec-0 {
+ sound-dai = <&acodec>;
+ };
+ };
+ };
+};
+
+&acodec {
+ AVDD-supply = <&vddio_ao18>;
+ status = "okay";
+};
+
+&aiu {
+ status = "okay";
};
&cec_AO {
@@ -97,6 +97,14 @@
pinctrl-names = "default";
};
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
&saradc {
status = "okay";
vref-supply = <&vddio_ao18>;
@@ -125,6 +133,11 @@
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
};
/* SD card */
@@ -165,14 +178,6 @@
vqmmc-supply = <&vddio_boot>;
};
-&pwm_ef {
- status = "okay";
- pinctrl-0 = <&pwm_e_pins>;
- pinctrl-names = "default";
- clocks = <&clkc CLKID_FCLK_DIV4>;
- clock-names = "clkin0";
-};
-
/* This is connected to the Bluetooth module: */
&uart_A {
status = "okay";
@@ -312,8 +312,8 @@
};
&gpio_intc {
- compatible = "amlogic,meson-gpio-intc",
- "amlogic,meson-gxl-gpio-intc";
+ compatible = "amlogic,meson-gxl-gpio-intc",
+ "amlogic,meson-gpio-intc";
status = "okay";
};
@@ -429,6 +429,20 @@
};
};
+ spi_idle_high_pins: spi-idle-high-pins {
+ mux {
+ groups = "spi_sclk";
+ bias-pull-up;
+ };
+ };
+
+ spi_idle_low_pins: spi-idle-low-pins {
+ mux {
+ groups = "spi_sclk";
+ bias-pull-down;
+ };
+ };
+
spi_ss0_pins: spi-ss0 {
mux {
groups = "spi_ss0";
@@ -759,16 +773,23 @@
};
};
- eth-phy-mux {
- compatible = "mdio-mux-mmioreg", "mdio-mux";
+ eth_phy_mux: mdio@558 {
+ reg = <0x0 0x558 0x0 0xc>;
+ compatible = "amlogic,gxl-mdio-mux";
#address-cells = <1>;
#size-cells = <0>;
- reg = <0x0 0x55c 0x0 0x4>;
- mux-mask = <0xffffffff>;
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "ref";
mdio-parent-bus = <&mdio0>;
- internal_mdio: mdio@e40908ff {
- reg = <0xe40908ff>;
+ external_mdio: mdio@0 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ internal_mdio: mdio@1 {
+ reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
@@ -779,12 +800,6 @@
max-speed = <100>;
};
};
-
- external_mdio: mdio@2009087f {
- reg = <0x2009087f>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
};
};
@@ -52,10 +52,11 @@
gpios = <&gpio GPIODV_14 GPIO_ACTIVE_HIGH
&gpio GPIODV_15 GPIO_ACTIVE_HIGH>;
/* Dummy RPM values since fan is optional */
- gpio-fan,speed-map = <0 0
- 1 1
- 2 2
- 3 3>;
+ gpio-fan,speed-map =
+ <0 0>,
+ <1 1>,
+ <2 2>,
+ <3 3>;
#cooling-cells = <2>;
};
@@ -270,7 +271,6 @@
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
- clock-frequency = <32768>;
clock-output-names = "xin32k";
};
};
@@ -307,7 +307,8 @@
#size-cells = <0>;
bus-width = <4>;
- max-frequency = <60000000>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
non-removable;
disable-wp;
@@ -373,7 +374,7 @@
pinctrl-0 = <&nor_pins>;
pinctrl-names = "default";
- w25q32: spi-flash@0 {
+ w25q32: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "winbond,w25q16", "jedec,spi-nor";
@@ -45,8 +45,6 @@
gpio-keys-polled {
compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
poll-interval = <100>;
button-power {
@@ -46,7 +46,7 @@ CONFIG_PHY_REALTEK=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -54,7 +54,7 @@ CONFIG_PHY_MESON_GXL=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -51,7 +51,7 @@ CONFIG_PHY_REALTEK=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -45,7 +45,7 @@ CONFIG_PHY_MESON_GXL=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -57,7 +57,7 @@ CONFIG_PHY_MESON_GXL=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -44,7 +44,7 @@ CONFIG_PHY_MESON_GXL=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -52,7 +52,7 @@ CONFIG_PHY_MESON_GXL=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_PHY=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
@@ -53,7 +53,7 @@ CONFIG_PHY_REALTEK=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -52,7 +52,7 @@ CONFIG_PHY_REALTEK=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -40,7 +40,7 @@ CONFIG_PHY_MESON_GXL=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
@@ -46,7 +46,7 @@ CONFIG_PHY_REALTEK=y
CONFIG_DM_MDIO=y
CONFIG_DM_MDIO_MUX=y
CONFIG_ETH_DESIGNWARE_MESON8B=y
-CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MDIO_MUX_MESON_GXL=y
CONFIG_MESON_GXL_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_GXL=y
Sync Amlogic GXBB, GXL & GXM DTs from Linux v6.4, and also switch to GXL MDIO MUX driver to adapt to DT change, Most of the changes are only cosmetic or doesn't concern U-Boot, the most important change for U-Boot is the GXL mdio mux compatible switch to amlogic,gxl-mdio-mux. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- arch/arm/dts/meson-gx-libretech-pc.dtsi | 4 +- arch/arm/dts/meson-gx.dtsi | 21 ++++--- arch/arm/dts/meson-gxbb-nanopi-k2.dts | 13 ++++- arch/arm/dts/meson-gxbb-odroidc2.dts | 26 ++++----- arch/arm/dts/meson-gxbb.dtsi | 18 +++++- arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 2 +- .../arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts | 12 +++- arch/arm/dts/meson-gxl-s905x-khadas-vim.dts | 16 +---- arch/arm/dts/meson-gxl-s905x-libretech-cc-v2.dts | 3 +- arch/arm/dts/meson-gxl-s905x-p212.dts | 68 ++++++++++++++++++++++ arch/arm/dts/meson-gxl-s905x-p212.dtsi | 21 ++++--- arch/arm/dts/meson-gxl.dtsi | 43 +++++++++----- arch/arm/dts/meson-gxm-khadas-vim2.dts | 15 ++--- arch/arm/dts/meson-gxm-wetek-core2.dts | 2 - configs/beelink-gt1-ultimate_defconfig | 2 +- configs/jethub_j80_defconfig | 2 +- configs/khadas-vim2_defconfig | 2 +- configs/khadas-vim_defconfig | 2 +- configs/libretech-ac_defconfig | 2 +- configs/libretech-cc_defconfig | 2 +- configs/libretech-cc_v2_defconfig | 2 +- configs/libretech-s905d-pc_defconfig | 2 +- configs/libretech-s912-pc_defconfig | 2 +- configs/p212_defconfig | 2 +- configs/wetek-core2_defconfig | 2 +- 25 files changed, 196 insertions(+), 90 deletions(-)