diff mbox series

[V3,3/3] ARM: dts: bcm2711: Add BCM2711 xHCI support

Message ID 20231202232217.89652-4-wahrenst@gmx.net
State Superseded
Headers show
Series ARM: dts: bcm2711: Add BCM2711 xHCI support | expand

Commit Message

Stefan Wahren Dec. 2, 2023, 11:22 p.m. UTC
The BCM2711 SoC also has a mostly generic xHCI. The USB port is
currently only usable on the Compute Module 4 (e.g. via IO board).
Because DWC2 and xHCI share the same PHY, we let the bootloader
enable it on demand.

Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
---
 arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi |  5 +++++
 arch/arm/boot/dts/broadcom/bcm2711.dtsi     | 14 ++++++++++++++
 2 files changed, 19 insertions(+)

--
2.34.1
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
index 98817a6675b9..d233a191c139 100644
--- a/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
@@ -1,6 +1,7 @@ 
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm2835-rpi.dtsi"

+#include <dt-bindings/power/raspberrypi-power.h>
 #include <dt-bindings/reset/raspberrypi,firmware-reset.h>

 / {
@@ -76,3 +77,7 @@  &v3d {
 &vchiq {
 	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 };
+
+&xhci {
+	power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm2711.dtsi b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
index 4a379a14966d..ed5ef36e08ff 100644
--- a/arch/arm/boot/dts/broadcom/bcm2711.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
@@ -604,6 +604,20 @@  genet_mdio: mdio@e14 {
 			};
 		};

+		xhci: usb@7e9c0000 {
+			compatible = "brcm,bcm2711-xhci";
+			reg = <0x0 0x7e9c0000 0x100000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+			/* DWC2 and this IP block share the same USB PHY,
+			 * enabling both at the same time results in lockups.
+			 * So keep this node disabled and let the bootloader
+			 * decide which interface should be enabled.
+			 */
+			status = "disabled";
+		};
+
 		v3d: gpu@7ec00000 {
 			compatible = "brcm,2711-v3d";
 			reg = <0x0 0x7ec00000 0x4000>,