diff mbox series

[v6,02/10] scsi: ufs: ufs-qcom: No need to set hs_rate after ufshcd_init_host_param()

Message ID 1701246516-11626-3-git-send-email-quic_cang@quicinc.com
State New
Headers show
Series Enable HS-G5 support on SM8550 | expand

Commit Message

Can Guo Nov. 29, 2023, 8:28 a.m. UTC
In ufs_qcom_pwr_change_notify(), host_params.hs_rate has been set to
PA_HS_MODE_B by ufshcd_init_host_param(), hence remove the duplicated line
of work. Meanwhile, removed the macro UFS_QCOM_LIMIT_HS_RATE as it is only
used here.

Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
---
 drivers/ufs/host/ufs-qcom.c | 1 -
 drivers/ufs/host/ufs-qcom.h | 2 --
 2 files changed, 3 deletions(-)

Comments

Andrew Halaney Nov. 29, 2023, 8:48 p.m. UTC | #1
On Wed, Nov 29, 2023 at 12:28:27AM -0800, Can Guo wrote:
> In ufs_qcom_pwr_change_notify(), host_params.hs_rate has been set to
> PA_HS_MODE_B by ufshcd_init_host_param(), hence remove the duplicated line
> of work. Meanwhile, removed the macro UFS_QCOM_LIMIT_HS_RATE as it is only
> used here.
> 
> Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Signed-off-by: Can Guo <quic_cang@quicinc.com>

Reviewed-by: Andrew Halaney <ahalaney@redhat.com>

> ---
>  drivers/ufs/host/ufs-qcom.c | 1 -
>  drivers/ufs/host/ufs-qcom.h | 2 --
>  2 files changed, 3 deletions(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 197c5a5..c21ff2c 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -909,7 +909,6 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>  	switch (status) {
>  	case PRE_CHANGE:
>  		ufshcd_init_host_params(&host_params);
> -		host_params.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
>  
>  		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
>  		host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
> diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
> index 9950a00..82cd143 100644
> --- a/drivers/ufs/host/ufs-qcom.h
> +++ b/drivers/ufs/host/ufs-qcom.h
> @@ -27,8 +27,6 @@
>  #define SLOW 1
>  #define FAST 2
>  
> -#define UFS_QCOM_LIMIT_HS_RATE		PA_HS_MODE_B
> -
>  /* QCOM UFS host controller vendor specific registers */
>  enum {
>  	REG_UFS_SYS1CLK_1US                 = 0xC0,
> -- 
> 2.7.4
> 
>
diff mbox series

Patch

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 197c5a5..c21ff2c 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -909,7 +909,6 @@  static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 	switch (status) {
 	case PRE_CHANGE:
 		ufshcd_init_host_params(&host_params);
-		host_params.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
 
 		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
 		host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
index 9950a00..82cd143 100644
--- a/drivers/ufs/host/ufs-qcom.h
+++ b/drivers/ufs/host/ufs-qcom.h
@@ -27,8 +27,6 @@ 
 #define SLOW 1
 #define FAST 2
 
-#define UFS_QCOM_LIMIT_HS_RATE		PA_HS_MODE_B
-
 /* QCOM UFS host controller vendor specific registers */
 enum {
 	REG_UFS_SYS1CLK_1US                 = 0xC0,