| Message ID | 1472213965-4899-1-git-send-email-jun.nie@linaro.org |
|---|---|
| State | New |
| Headers | show |
2016-09-06 22:15 GMT+08:00 Linus Walleij <linus.walleij@linaro.org>: > Please always include devicetree@vger.kernel.org on subsequent > postings of the bindings. > > Also include Heiko Stübner and Doug Andersson who are also > interested in hierarchical pin controllers on subsequent postings. > > On Fri, Aug 26, 2016 at 2:19 PM, Jun Nie <jun.nie@linaro.org> wrote: > >> +The pins controlled by ZX pin controller are organized in banks, >> +number of pins in each bank may vary. Each pin has different multiplexing >> +functions. There are two type of pins, normal ones and AON ones. > > I understand so far. Spell out what the acronym AON means. Does > it mean "always-on?" > >> + AON >> +pins control high level multiplex and normal pins may require multiplex >> +configuration of parent AON pins. > > I don't understand this at all. > > What is "high level multiplex"? > > Since you mention parents I suspect that what you are referring to is > that the pins are hierarchical, and that they are controlled by two > levels of pin controllers, such that a physical pin is connected to pin > controller A which can multiplex pins to N functions, and then the line > from A is connected to another pin controller B that can again multiplex > to M other functions? > > Please describe this hardware set-up with *lots* of detail so we have > a chance of understanding it fully. All necessary information shall go > into this DT binding document so we know where to look it up. > Here is more hardware detail. Will add it to document later. Hardware has two register regions to control pinmux, one is for normal function configuration and the other one is for always on subsystem(AON). Some pins are controlled by both normal register and AON register, while some pins are controlled only by normal register. That means some pins are hierarchical, AON register is the 1st level control for pinmux. If we need any function in normal register pin multiplexing, we need configure related AON pinmux register to non-AON function first. Then we configure normal pinmux register to get the pin function we want. For those pins that are not controlled by AON registers, we just need to configure normal pinmux register for function multiplexing. All pin configuration, such as pull up/down, is controlled by registers in AON register region, which is layouted just after AON pinmux registers. So we need access AON register region even we are configuring normal pins which has no AON pin multiplex functions. >> + As the AON pins number is not as much as >> +normal pins, some normal pins are not routed through AON pin side and are >> +under direct control by itself. > > I don't understand this. I suspect the English language may be a > problem here, I think "as much as" should be "as many as", also > subject and object is very hard to understand when the pin controller > is referred to as "itself". It's just very hard to parse, sorry. Please > elaborate and I will try to understand and help as much as I can. > >> +Required properties: >> +- compatible: >> + "zte,zx296718-pinctrl" >> + "zte,zx296718-aonpmx" >> + >> +- reg: Should contain the register physical address and length for the >> + pin controller. > > OK > >> +IO pull up/down etc configuration is supported with unified management of >> +normal pins and AON pins. The configuration registers area is just after >> +AON pinmux reg area, while normal pins regs in different area. So two dts >> +nodes are needed to provides the two reg regions. > > Again hard to understand, but why do you need two nodes > and not just two register areas regs = <a b>, <c d>;? > > I guess because one pin controller is using another one but > I'm not sure. Thanks for pointing the usage of regs = <a b>, <c d>; For normal pinmux function, we still need AON registers for pin configuration, maybe this is what you care. > >> +Below configuration are supported. Please refer to pinctrl-bindings.txt >> +in this directory for more details of the common pinctrl bindings used >> +by client devices. >> + >> +bias-pull-up - pull up the pin >> +bias-pull-down - pull down the pin >> +drive-strength - sink or source at most 7 mA >> +input-enable - enable input on pin (no effect on output) >> +power-source - select power supplies. 1: 1.8V, 0: 3.3V >> +slew-rate - set the slew rate > > OK > >> +Pin names are defined by bank sequence and pins number in the bank. For >> +example, B2 is the 3rd pin in the second bank. The AON pin has prefix >> +AON, like AONC2. > > OK > >> +Example dts nodes: >> + >> +pinctop: pinctrl@01462000 { >> + compatible = "zte,zx296718-pinctrl"; >> + reg = <0x01462000 0x1000>; >> + >> + i2c5_pins: i2c5pins { >> + pins = "G6", "G7"; >> + function = "I2C5"; >> + } >> +}; >> + >> +pmx_aon: pinctrl@00119000 { >> + compatible = "zte,zx296718-aonpmx"; >> + reg = <0x00119000 0x1000>; >> +}; > > The problem with this devicetree is that it does not express the hierarchical > nature that you describe above. And I have no idea how the driver > handles that relation. These look like two independent pin controller > but AFAICT they are not. > > These are arrangements that make more sense: > > pinctrla { > compatible = "parent-device-compat"; > (...) > pinctrlb { > compatible = "child-device-compat"; > (...) > }; > }; > > This makes the child pin controller a proper child of the parent and > make the child probe instantiate from the parent (in > Linux of_platform_default_populate() inside the parent driver) > and thus it knows the parent is always available before the child. > > Another arrangement is: > > pa: pinctrla { > compatible = "parent-device-compat"; > (...) > }; > > pb: pinctrlb { > compatible = "child-device-compat"; > pinctrl-parent = &pinctrla; > (...) > }; > > This is in case we need to have hierarchies defined this way. Yes, the two arrangements are clearer to show the parent relation. > > I don't know the best way to define hierarchical pin controllers yet > so we definately need some discussion about it. > > Yours, > Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt new file mode 100644 index 0000000..4061f51 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt @@ -0,0 +1,54 @@ +* ZTE ZX Pin Controller + +The pins controlled by ZX pin controller are organized in banks, +number of pins in each bank may vary. Each pin has different multiplexing +functions. There are two type of pins, normal ones and AON ones. AON +pins control high level multiplex and normal pins may require multiplex +configuration of parent AON pins. As the AON pins number is not as much as +normal pins, some normal pins are not routed through AON pin side and are +under direct control by itself. + +Required properties: +- compatible: + "zte,zx296718-pinctrl" + "zte,zx296718-aonpmx" + +- reg: Should contain the register physical address and length for the + pin controller. + +IO pull up/down etc configuration is supported with unified management of +normal pins and AON pins. The configuration registers area is just after +AON pinmux reg area, while normal pins regs in different area. So two dts +nodes are needed to provides the two reg regions. + +Below configuration are supported. Please refer to pinctrl-bindings.txt +in this directory for more details of the common pinctrl bindings used +by client devices. + +bias-pull-up - pull up the pin +bias-pull-down - pull down the pin +drive-strength - sink or source at most 7 mA +input-enable - enable input on pin (no effect on output) +power-source - select power supplies. 1: 1.8V, 0: 3.3V +slew-rate - set the slew rate + +Pin names are defined by bank sequence and pins number in the bank. For +example, B2 is the 3rd pin in the second bank. The AON pin has prefix +AON, like AONC2. + +Example dts nodes: + +pinctop: pinctrl@01462000 { + compatible = "zte,zx296718-pinctrl"; + reg = <0x01462000 0x1000>; + + i2c5_pins: i2c5pins { + pins = "G6", "G7"; + function = "I2C5"; + } +}; + +pmx_aon: pinctrl@00119000 { + compatible = "zte,zx296718-aonpmx"; + reg = <0x00119000 0x1000>; +};
Add initial ZTE pinctrl dts document for ZX296718 SoC. Signed-off-by: Jun Nie <jun.nie@linaro.org> --- .../devicetree/bindings/pinctrl/pinctrl-zx.txt | 54 ++++++++++++++++++++++ 1 file changed, 54 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html