@@ -176,6 +176,7 @@
#define AT8030_PHY_ID_MASK 0xffffffef
#define QCA8081_PHY_ID 0x004dd101
+#define QCA8084_PHY_ID 0x004dd180
#define QCA8327_A_PHY_ID 0x004dd033
#define QCA8327_B_PHY_ID 0x004dd034
@@ -1760,6 +1761,9 @@ static bool qca808x_is_prefer_master(struct phy_device *phydev)
static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
{
+ if (phydev_id_compare(phydev, QCA8084_PHY_ID))
+ return false;
+
return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
}
@@ -1824,6 +1828,21 @@ static int qca808x_read_status(struct phy_device *phydev)
return ret;
if (phydev->link) {
+ /* There are two PCSs available for QCA8084, which support the following
+ * interface modes.
+ *
+ * 1. PHY_INTERFACE_MODE_10G_QXGMII utilizes PCS1 for all available 4 ports,
+ * which is for all link speeds.
+ *
+ * 2. PHY_INTERFACE_MODE_2500BASEX utilizes PCS0 for the fourth port,
+ * which is only for the link speed 2500M same as QCA8081.
+ *
+ * 3. PHY_INTERFACE_MODE_SGMII utilizes PCS0 for the fourth port,
+ * which is for the link speed 10M, 100M and 1000M same as QCA8081.
+ */
+ if (phydev->interface == PHY_INTERFACE_MODE_10G_QXGMII)
+ return 0;
+
if (phydev->speed == SPEED_2500)
phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
else
@@ -1958,6 +1977,14 @@ static int qca808x_cable_test_start(struct phy_device *phydev)
phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
+ if (phydev_id_compare(phydev, QCA8084_PHY_ID)) {
+ /* Adjust the positive and negative pulse thereshold of CDT */
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8075, 0xa060);
+
+ /* Disable the near echo bypass */
+ phy_modify_mmd(phydev, MDIO_MMD_PCS, 0x807f, BIT(15), 0);
+ }
+
return 0;
}
@@ -2227,6 +2254,26 @@ static struct phy_driver at803x_driver[] = {
.cable_test_start = qca808x_cable_test_start,
.cable_test_get_status = qca808x_cable_test_get_status,
.link_change_notify = qca808x_link_change_notify,
+}, {
+ /* Qualcomm QCA8084 */
+ PHY_ID_MATCH_MODEL(QCA8084_PHY_ID),
+ .name = "Qualcomm QCA8084",
+ .flags = PHY_POLL_CABLE_TEST,
+ .probe = at803x_probe,
+ .config_intr = at803x_config_intr,
+ .handle_interrupt = at803x_handle_interrupt,
+ .get_tunable = at803x_get_tunable,
+ .set_tunable = at803x_set_tunable,
+ .set_wol = at803x_set_wol,
+ .get_wol = at803x_get_wol,
+ .get_features = qca808x_get_features,
+ .config_aneg = at803x_config_aneg,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .read_status = qca808x_read_status,
+ .soft_reset = qca808x_soft_reset,
+ .cable_test_start = qca808x_cable_test_start,
+ .cable_test_get_status = qca808x_cable_test_get_status,
}, };
module_phy_driver(at803x_driver);
@@ -2242,6 +2289,7 @@ static struct mdio_device_id __maybe_unused atheros_tbl[] = {
{ PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) },
{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
{ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
+ { PHY_ID_MATCH_MODEL(QCA8084_PHY_ID) },
{ }
};
Add qca8084 PHY support, which is four-port PHY with maximum link capability 2.5G, the features of each port is almost same as QCA8081 and slave seed config is not needed. Three kind of interface modes supported by qca8084. PHY_INTERFACE_MODE_10G_QXGMII, PHY_INTERFACE_MODE_2500BASEX and PHY_INTERFACE_MODE_SGMII. The PCS(serdes) and clock are also needed to be configured to bringup qca8084 PHY, which will be added in the pcs driver. The additional CDT configurations used for qca8084. Signed-off-by: Luo Jie <quic_luoj@quicinc.com> --- drivers/net/phy/at803x.c | 48 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+)