@@ -154,6 +154,7 @@ Hardware Monitoring Kernel Drivers
mcp3021
menf21bmc
mlxreg-fan
+ mp2856
mp2888
mp2975
mp5023
new file mode 100644
@@ -0,0 +1,101 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2856
+====================
+
+Supported chips:
+
+ * MPS MP2856
+
+ Prefix: 'mp2856'
+
+ * MPS MP2857
+
+ Prefix: 'mp2857'
+
+Author:
+
+ Peter Yin <peter.yin@quantatw.com>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+vendor dual-loop, digital, multi-phase controller MP2856/MP2857
+
+This device:
+
+- Supports up to two power rail.
+- Supports two pages 0 and 1 for and also pages 2 for configuration.
+- Can configured VOUT readout in direct or VID format and allows
+ setting of different formats on rails 1 and 2. For VID the following
+ protocols are available: AMD SVI3 mode with 5-mV/LSB.
+
+Device supports:
+
+- SVID interface.
+- AVSBus interface.
+
+Device complaint with:
+
+- PMBus rev 1.3 interface.
+
+Device supports direct format for reading output current, output voltage,
+input and output power and temperature.
+Device supports linear format for reading input voltage and input power.
+Device supports VID and direct formats for reading output voltage.
+The below VID modes are supported: AMD SVI3.
+
+The driver provides the next attributes for the current:
+The driver exports the following attributes via the 'sysfs' files, where
+
+- indexes 1 for "iin";
+- indexes 2, 3 for "iout";
+
+**curr[1-3]_alarm**
+
+**curr[1-3]_input**
+
+**curr[1-3]_label**
+
+The driver provides the next attributes for the voltage:
+The driver exports the following attributes via the 'sysfs' files, where
+
+- indexes 1 for "vin";
+- indexes 2, 3 for "vout";
+
+**in[1-3]_crit**
+
+**in[1-3]_crit_alarm**
+
+**in[1-3]_input**
+
+**in[1-3]_label**
+
+**in[1-3]_lcrit**
+
+**in[1-3]_lcrit_alarm**
+
+The driver provides the next attributes for the power:
+The driver exports the following attributes via the 'sysfs' files, where
+
+- indexes 1 for "pin";
+- indexes 2, 3 for "pout";
+
+**power[1-3]_alarm**
+
+**power[1-3]_input**
+
+**power[1-3]_label**
+
+The driver provides the next attributes for the temperature:
+
+**temp[1-2]_crit**
+
+**temp[1-2]_crit_alarm**
+
+**temp[1-2]_input**
+
+**temp[1-2]_max**
+
+**temp[1-2]_max_alarm**
@@ -299,6 +299,15 @@ config SENSORS_MAX8688
This driver can also be built as a module. If so, the module will
be called max8688.
+config SENSORS_MP2856
+ tristate "MPS MP2856"
+ help
+ If you say yes here you get hardware monitoring support for MPS
+ MP2856 MP2857 Dual Loop Digital Multi-Phase Controller.
+
+ This driver can also be built as a module. If so, the module will
+ be called mp2856.
+
config SENSORS_MP2888
tristate "MPS MP2888"
help
@@ -32,6 +32,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
+obj-$(CONFIG_SENSORS_MP2856) += mp2856.o
obj-$(CONFIG_SENSORS_MP2888) += mp2888.o
obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
obj-$(CONFIG_SENSORS_MP5023) += mp5023.o
new file mode 100644
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for MPS2856/2857
+ * Monolithic Power Systems VR Controllers
+ *
+ * Copyright (C) 2023 Quanta Computer lnc.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pmbus.h>
+#include "pmbus.h"
+
+/* Vendor specific registers. */
+#define MP2856_MFR_SLOPE_TRIM3 0x1d
+#define MP2856_MFR_VR_MULTI_CONFIG_R1 0x0d
+#define MP2856_MFR_VR_MULTI_CONFIG_R2 0x1d
+#define MP2856_MUL1_CUR_SCALE_R1 0x0b
+#define MP2856_MUL1_CUR_SCALE_R2 0x1b
+#define MP2856_MFR_DC_LOOP_CTRL 0x59
+#define MP2856_MFR_VR_CONFIG1 0x68
+#define MP2856_MFR_READ_IOUT_PK 0x90
+#define MP2856_MFR_READ_POUT_PK 0x91
+#define MP2856_MFR_PROTECT_SET 0xc5
+#define MP2856_MFR_RESO_SET 0x5e
+#define MP2856_MFR_OVP_TH_SET 0xe5
+#define MP2856_MFR_UVP_SET 0xe6
+
+#define MP2856_VID_EN BIT(11)
+#define MP2856_DRMOS_KCS GENMASK(15, 12)
+#define MP2856_VID_SCALE 5
+#define MP2856_VIN_UV_LIMIT_UNIT 8
+#define MP2856_PWR_EXPONENT_BIT GENMASK(10, 6)
+
+#define MP2856_MAX_PHASE_RAIL1 12
+#define MP2856_MAX_PHASE_RAIL2 6
+#define MP2856_PAGE_NUM 2
+
+#define MP2856_RAIL2_FUNC (PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | \
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | \
+ PMBUS_HAVE_POUT | PMBUS_HAVE_TEMP)
+
+#define MP2856_RAIL2_MAX_PHASE 4
+
+struct mp2856_data {
+ struct pmbus_driver_info info;
+ int vout_format[MP2856_PAGE_NUM];
+};
+
+#define to_mp2856_data(x) container_of(x, struct mp2856_data, info)
+
+static int
+mp2856_read_word_helper(struct i2c_client *client, int page, int phase, u8 reg,
+ u16 mask)
+{
+ int ret = pmbus_read_word_data(client, page, phase, reg);
+
+ return (ret > 0) ? ret & mask : ret;
+}
+
+static int
+mp2856_vid2linear(int val)
+{
+ return 500 + (val - 1) * 10;
+}
+
+static int mp2856_read_word_data(struct i2c_client *client, int page,
+ int phase, int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp2856_data *data = to_mp2856_data(info);
+ int ret;
+
+ switch (reg) {
+ case PMBUS_READ_VOUT:
+ ret = mp2856_read_word_helper(client, page, phase, reg,
+ GENMASK(11, 0));
+ if (ret < 0)
+ return ret;
+
+ /*
+ * READ_VOUT can be provided in VID or linear format. This
+ * provided in a linear format. In case format is VID - convert
+ * to linear.
+ */
+ if (data->vout_format[page] == vid)
+ ret = mp2856_vid2linear(ret);
+ break;
+ default:
+ return -ENODATA;
+ }
+
+ return ret;
+}
+
+static int mp2856_identify_multiphase_rail2(struct i2c_client *client)
+{
+ int ret;
+
+ /*
+ * Identify multiphase for rail 2 - could be from 0 to 1.
+ * In case phase number is zero – only page zero is supported
+ */
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ /* Identify multiphase for rail 2 - could be from 0 to 1. */
+ ret = i2c_smbus_read_word_data(client, MP2856_MFR_VR_MULTI_CONFIG_R2);
+ if (ret < 0)
+ return ret;
+
+ ret &= GENMASK(2, 0);
+ return (ret >= MP2856_RAIL2_MAX_PHASE) ? MP2856_RAIL2_MAX_PHASE : ret;
+}
+
+static int
+mp2856_identify_vid(struct i2c_client *client, struct mp2856_data *data,
+ struct pmbus_driver_info *info, u32 reg, int page,
+ u32 imvp_bit)
+{
+ int ret;
+
+ /* Identify VID mode and step selection. */
+ ret = i2c_smbus_read_word_data(client, reg);
+ if (ret < 0)
+ return ret;
+
+ if (ret & imvp_bit) {
+ info->vrm_version[page] = vr13;
+ } else {
+ //workaround for chip power scale issue
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_read_word_data(client,
+ MP2856_MUL1_CUR_SCALE_R1);
+ if (ret < 0)
+ return ret;
+
+ ret &= ~MP2856_PWR_EXPONENT_BIT;
+ ret = i2c_smbus_write_word_data(client,
+ MP2856_MUL1_CUR_SCALE_R1, ret);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_read_word_data(client,
+ MP2856_MUL1_CUR_SCALE_R2);
+ if (ret < 0)
+ return ret;
+
+ ret &= ~MP2856_PWR_EXPONENT_BIT;
+ ret = i2c_smbus_write_word_data(client,
+ MP2856_MUL1_CUR_SCALE_R2, ret);
+ if (ret < 0)
+ return ret;
+ }
+ return 0;
+}
+
+static int
+mp2856_identify_rails_vid(struct i2c_client *client, struct mp2856_data *data,
+ struct pmbus_driver_info *info)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 1. */
+ ret = mp2856_identify_vid(client, data, info,
+ MP2856_MFR_RESO_SET, 0,
+ MP2856_VID_EN);
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 2, if connected. */
+ if (info->phases[1])
+ ret = mp2856_identify_vid(client, data, info,
+ MP2856_MFR_RESO_SET, 1,
+ MP2856_VID_EN);
+ return ret;
+}
+
+static int
+mp2856_identify_vout_format(struct i2c_client *client,
+ struct mp2856_data *data, int page)
+{
+ int ret;
+ int val;
+
+ ret = i2c_smbus_read_word_data(client, MP2856_MFR_RESO_SET);
+ if (ret < 0)
+ return ret;
+
+ val = (ret & GENMASK(11, 11)) >> 11;
+ switch (val) {
+ case 0:
+ data->vout_format[page] = vid;
+ break;
+ default:
+ data->vout_format[page] = linear;
+ break;
+ }
+ return 0;
+}
+
+static int
+mp2856_vout_per_rail_config_get(struct i2c_client *client,
+ struct mp2856_data *data,
+ struct pmbus_driver_info *info)
+{
+ int i, ret;
+
+ for (i = 0; i < data->info.pages; i++) {
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, i);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Get VOUT format for READ_VOUT command : VID or direct.
+ * Pages on same device can be configured with different
+ * formats.
+ */
+ ret = mp2856_identify_vout_format(client, data, i);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct pmbus_driver_info mp2856_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_POUT |
+ PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT,
+ .read_word_data = mp2856_read_word_data,
+};
+
+static int mp2856_probe(struct i2c_client *client)
+{
+ struct pmbus_driver_info *info;
+ struct mp2856_data *data;
+ int ret;
+
+ /*
+ * MP2856/MP2857 devices may not stay in page 0 during device
+ * probe which leads to probe failure (read status word failed).
+ * So let's set the device to page 0 at the beginning.
+ */
+ i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
+
+ data = devm_kzalloc(&client->dev, sizeof(struct mp2856_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ memcpy(&data->info, &mp2856_info, sizeof(*info));
+ info = &data->info;
+
+ /* Identify multiphase configuration for rail 2. */
+ ret = mp2856_identify_multiphase_rail2(client);
+ if (ret < 0)
+ return ret;
+
+ if (ret) {
+ /* Two rails are connected. */
+ data->info.pages = MP2856_PAGE_NUM;
+ data->info.phases[1] = ret;
+ data->info.func[1] = MP2856_RAIL2_FUNC;
+ }
+
+ ret = mp2856_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
+
+ /* Obtain offsets, maximum and format for vout. */
+ ret = mp2856_vout_per_rail_config_get(client, data, info);
+ if (ret)
+ return ret;
+
+ return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2856_id[] = {
+ {"mp2856", 0},
+ {"mp2857", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2856_id);
+
+static const struct of_device_id __maybe_unused mp2856_of_match[] = {
+ {.compatible = "mps,mp2856"},
+ {.compatible = "mps,mp2857"},
+ {}
+};
+MODULE_DEVICE_TABLE(of, mp2856_of_match);
+
+static struct i2c_driver mp2856_driver = {
+ .driver = {
+ .name = "mp2856",
+ .of_match_table = mp2856_of_match,
+ },
+ .probe = mp2856_probe,
+ .id_table = mp2856_id,
+};
+
+module_i2c_driver(mp2856_driver);
+
+MODULE_AUTHOR("Peter Yin <peter.yin@quantatw.com>");
+MODULE_DESCRIPTION("PMBus driver for MPS MP2856/MP2857 device");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PMBUS);