| Message ID | 20231104-topic-rb2_wifi-v1-1-fd45ae535d2f@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: qcom: qrb4210-rb2: Enable MPSS and Wi-Fi | expand |
On Sat, 04 Nov 2023 21:56:35 +0100, Konrad Dybcio wrote: > Enable the remote processors and tighten up the regulators to enable > Wi-Fi functionality on the RB2. > > For reference, the hw/sw identifies as: > > qmi chip_id 0x150 chip_family 0x4002 board_id 0xff soc_id 0x40670000 > qmi fw_version 0x337302d3 fw_build_timestamp 2023-01-06 01:50 > fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.3.7.c2-00723-QCAHLSWMTPLZ-1 > wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000 > kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0 > firmware ver api 5 features wowlan,mgmt-tx-by-reference,non-bmi > crc32 b3d4b790 > htt-ver 3.114 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1 > > [...] Applied, thanks! [1/1] arm64: dts: qcom: qrb4210-rb2: Enable MPSS and Wi-Fi commit: ff753723bf3916770c1e2580fe1f34ad9d6f0283 Best regards,
diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts index 9738c0dacd58..c2d7e3998d05 100644 --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts @@ -280,6 +280,12 @@ &remoteproc_cdsp { status = "okay"; }; +&remoteproc_mpss { + firmware-name = "qcom/qrb4210/modem.mbn"; + + status = "okay"; +}; + &rpm_requests { regulators { compatible = "qcom,rpm-pm6125-regulators"; @@ -346,8 +352,8 @@ vreg_l7a_1p256: l7 { }; vreg_l8a_0p664: l8 { - regulator-min-microvolt = <400000>; - regulator-max-microvolt = <728000>; + regulator-min-microvolt = <640000>; + regulator-max-microvolt = <640000>; }; vreg_l9a_1p8: l9 { @@ -424,8 +430,8 @@ vreg_l22a_2p96: l22 { }; vreg_l23a_3p3: l23 { - regulator-min-microvolt = <3200000>; - regulator-max-microvolt = <3400000>; + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; }; vreg_l24a_2p96: l24 { @@ -535,6 +541,16 @@ &usb_qmpphy { status = "okay"; }; +&wifi { + vdd-0.8-cx-mx-supply = <&vreg_l8a_0p664>; + vdd-1.8-xo-supply = <&vreg_l16a_1p3>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l23a_3p3>; + qcom,ath10k-calibration-variant = "Thundercomm_RB2"; + + status = "okay"; +}; + &xo_board { clock-frequency = <19200000>; };
Enable the remote processors and tighten up the regulators to enable Wi-Fi functionality on the RB2. For reference, the hw/sw identifies as: qmi chip_id 0x150 chip_family 0x4002 board_id 0xff soc_id 0x40670000 qmi fw_version 0x337302d3 fw_build_timestamp 2023-01-06 01:50 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.3.7.c2-00723-QCAHLSWMTPLZ-1 wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000 kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0 firmware ver api 5 features wowlan,mgmt-tx-by-reference,non-bmi crc32 b3d4b790 htt-ver 3.114 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1 Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 24 ++++++++++++++++++++---- 1 file changed, 20 insertions(+), 4 deletions(-) --- base-commit: e27090b1413ff236ca1aec26d6b022149115de2c change-id: 20231104-topic-rb2_wifi-fa773c5f55ec Best regards,