| Message ID | 20231014172624.75301-3-otto.pflueger@abscue.de |
|---|---|
| State | New |
| Headers | show |
| Series | ASoC: qcom: check ADSP version when setting clocks | expand |
Thanks Otto for the patch, some comments below On 14/10/2023 18:26, Otto Pflüger wrote: > There are two APIs for setting clocks: the old one that uses > AFE_PARAM_ID_INT_DIGITAL_CDC_CLK_CONFIG and AFE_PARAM_ID_LPAIF_CLK_CONFIG, > and the new one which uses AFE_PARAM_ID_CLOCK_SET. > > ADSP firmware version 2.6 only provides the old API, while newer > firmware versions only provide the new API. > > Implement LPAIF_BIT_CLK and LPAIF_DIG_CLK for both APIs so that users > don't have to care about the firmware version. Also fall back to > setting AFE_PARAM_ID_INT_DIGITAL_CDC_CLK_CONFIG in q6afe_set_lpass_clock > when setting the new Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE > clock is requested to allow specifying it in the device tree on older > platforms too. > > Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> > --- > sound/soc/qcom/qdsp6/q6afe.c | 81 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 81 insertions(+) > > diff --git a/sound/soc/qcom/qdsp6/q6afe.c b/sound/soc/qcom/qdsp6/q6afe.c > index 91d39f6ad0bd..87bdf741e5f6 100644 > --- a/sound/soc/qcom/qdsp6/q6afe.c > +++ b/sound/soc/qcom/qdsp6/q6afe.c > @@ -1111,6 +1111,32 @@ int q6afe_set_lpass_clock(struct device *dev, int clk_id, int attri, > struct q6afe *afe = dev_get_drvdata(dev->parent); > struct afe_clk_set cset = {0,}; > > + /* > + * v2 clocks specified in the device tree may not be supported by the > + * firmware. If this is the digital codec core clock, fall back to the > + * old method for setting it. > + */ > + if (q6core_get_adsp_version() < Q6_ADSP_VERSION_2_7) { > + struct q6afe_port *port; > + struct afe_digital_clk_cfg dcfg = {0,}; > + int ret; > + > + if (clk_id != Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE) > + return -EINVAL; > + <--- > + port = q6afe_port_get_from_id(dev, PRIMARY_MI2S_RX); > + if (IS_ERR(port)) > + return PTR_ERR(port); > + > + dcfg.i2s_cfg_minor_version = AFE_API_VERSION_I2S_CONFIG; > + dcfg.clk_val = freq; > + dcfg.clk_root = 5; > + ret = q6afe_set_digital_codec_core_clock(port, &dcfg); > + > + q6afe_port_put(port); ---> Could you pl explain what are we doing in this snippet? Isn't this what is exactly done in q6afe_mi2s_set_sysclk(LPAIF_DIG_CLK...) > + return ret; > + } > + > cset.clk_set_minor_version = AFE_API_VERSION_CLOCK_SET; > cset.clk_id = clk_id; > cset.clk_freq_in_hz = freq; > @@ -1124,6 +1150,41 @@ int q6afe_set_lpass_clock(struct device *dev, int clk_id, int attri, > } > EXPORT_SYMBOL_GPL(q6afe_set_lpass_clock); > ... > int q6afe_port_set_sysclk(struct q6afe_port *port, int clk_id, > int clk_src, int clk_root, > unsigned int freq, int dir) > @@ -1133,6 +1194,26 @@ int q6afe_port_set_sysclk(struct q6afe_port *port, int clk_id, > struct afe_digital_clk_cfg dcfg = {0,}; > int ret; > > + if (q6core_get_adsp_version() >= Q6_ADSP_VERSION_2_7) { > + /* Always use the new clock API on newer platforms. */ > + switch (clk_id) { > + case LPAIF_DIG_CLK: > + clk_src = Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO; > + clk_root = Q6AFE_LPASS_CLK_ROOT_DEFAULT; > + clk_id = Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE; > + break; > + case LPAIF_BIT_CLK: > + clk_src = Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO; > + clk_root = Q6AFE_LPASS_CLK_ROOT_DEFAULT; > + clk_id = q6afe_get_v2_bit_clk_id(port); > + if (clk_id < 0) > + return clk_id; > + break; > + default: > + break; > + } > + } This should be probably done in machine driver or q6afe-dai, not in q6afe. > + > switch (clk_id) { > case LPAIF_DIG_CLK: > dcfg.i2s_cfg_minor_version = AFE_API_VERSION_I2S_CONFIG;
[...] > > <--- > > + port = q6afe_port_get_from_id(dev, PRIMARY_MI2S_RX); > > + if (IS_ERR(port)) > > + return PTR_ERR(port); > > + > > + dcfg.i2s_cfg_minor_version = AFE_API_VERSION_I2S_CONFIG; > > + dcfg.clk_val = freq; > > + dcfg.clk_root = 5; > > + ret = q6afe_set_digital_codec_core_clock(port, &dcfg); > > + > > + q6afe_port_put(port); > ---> > > Could you pl explain what are we doing in this snippet? > > Isn't this what is exactly done in q6afe_mi2s_set_sysclk(LPAIF_DIG_CLK...) > > Yes, this is the same, except that q6afe_mi2s_set_sysclk is in q6afe-dai.c and relies on being part of the DAI, while this is called from q6afe-clocks.c in a context which doesn't necessarily require a DAI to be present, e.g. if q6afe-clocks is used as a simple clock controller without any DAIs defined in the device tree. Setting the digital codec clock always requires a port, but it isn't relevant which port is used here because there is usually only one codec clock. > > > > + return ret; > > + } > > + > > cset.clk_set_minor_version = AFE_API_VERSION_CLOCK_SET; > > cset.clk_id = clk_id; > > cset.clk_freq_in_hz = freq; > > @@ -1124,6 +1150,41 @@ int q6afe_set_lpass_clock(struct device *dev, int clk_id, int attri, > > } > > EXPORT_SYMBOL_GPL(q6afe_set_lpass_clock); > ... > > > int q6afe_port_set_sysclk(struct q6afe_port *port, int clk_id, > > int clk_src, int clk_root, > > unsigned int freq, int dir) > > @@ -1133,6 +1194,26 @@ int q6afe_port_set_sysclk(struct q6afe_port *port, int clk_id, > > struct afe_digital_clk_cfg dcfg = {0,}; > > int ret; > > + if (q6core_get_adsp_version() >= Q6_ADSP_VERSION_2_7) { > > + /* Always use the new clock API on newer platforms. */ > > + switch (clk_id) { > > + case LPAIF_DIG_CLK: > > + clk_src = Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO; > > + clk_root = Q6AFE_LPASS_CLK_ROOT_DEFAULT; > > + clk_id = Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE; > > + break; > > + case LPAIF_BIT_CLK: > > + clk_src = Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO; > > + clk_root = Q6AFE_LPASS_CLK_ROOT_DEFAULT; > > + clk_id = q6afe_get_v2_bit_clk_id(port); > > + if (clk_id < 0) > > + return clk_id; > > + break; > > + default: > > + break; > > + } > > + } > > This should be probably done in machine driver or q6afe-dai, not in q6afe. > I'll put it in q6afe-dai since this fits nicely into the switch statement in q6afe_mi2s_set_sysclk. As stated in the cover letter, I don't think adding this to the machine driver is the best option. The LPAIF_* clocks look simple and generic enough to be usable by different drivers, and making those drivers care about different clock versions in the firmware doesn't seem right. > > > + > > switch (clk_id) { > > case LPAIF_DIG_CLK: > > dcfg.i2s_cfg_minor_version = AFE_API_VERSION_I2S_CONFIG;
diff --git a/sound/soc/qcom/qdsp6/q6afe.c b/sound/soc/qcom/qdsp6/q6afe.c index 91d39f6ad0bd..87bdf741e5f6 100644 --- a/sound/soc/qcom/qdsp6/q6afe.c +++ b/sound/soc/qcom/qdsp6/q6afe.c @@ -1111,6 +1111,32 @@ int q6afe_set_lpass_clock(struct device *dev, int clk_id, int attri, struct q6afe *afe = dev_get_drvdata(dev->parent); struct afe_clk_set cset = {0,}; + /* + * v2 clocks specified in the device tree may not be supported by the + * firmware. If this is the digital codec core clock, fall back to the + * old method for setting it. + */ + if (q6core_get_adsp_version() < Q6_ADSP_VERSION_2_7) { + struct q6afe_port *port; + struct afe_digital_clk_cfg dcfg = {0,}; + int ret; + + if (clk_id != Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE) + return -EINVAL; + + port = q6afe_port_get_from_id(dev, PRIMARY_MI2S_RX); + if (IS_ERR(port)) + return PTR_ERR(port); + + dcfg.i2s_cfg_minor_version = AFE_API_VERSION_I2S_CONFIG; + dcfg.clk_val = freq; + dcfg.clk_root = 5; + ret = q6afe_set_digital_codec_core_clock(port, &dcfg); + + q6afe_port_put(port); + return ret; + } + cset.clk_set_minor_version = AFE_API_VERSION_CLOCK_SET; cset.clk_id = clk_id; cset.clk_freq_in_hz = freq; @@ -1124,6 +1150,41 @@ int q6afe_set_lpass_clock(struct device *dev, int clk_id, int attri, } EXPORT_SYMBOL_GPL(q6afe_set_lpass_clock); +static int q6afe_get_v2_bit_clk_id(struct q6afe_port *port) +{ + switch (port->id) { + case AFE_PORT_ID_PRIMARY_MI2S_RX: + case AFE_PORT_ID_PRIMARY_MI2S_TX: + return Q6AFE_LPASS_CLK_ID_PRI_MI2S_IBIT; + case AFE_PORT_ID_SECONDARY_MI2S_RX: + case AFE_PORT_ID_SECONDARY_MI2S_TX: + return Q6AFE_LPASS_CLK_ID_SEC_MI2S_IBIT; + case AFE_PORT_ID_TERTIARY_MI2S_RX: + case AFE_PORT_ID_TERTIARY_MI2S_TX: + return Q6AFE_LPASS_CLK_ID_TER_MI2S_IBIT; + case AFE_PORT_ID_QUATERNARY_MI2S_RX: + case AFE_PORT_ID_QUATERNARY_MI2S_TX: + return Q6AFE_LPASS_CLK_ID_TER_MI2S_IBIT; + case AFE_PORT_ID_QUINARY_MI2S_RX: + case AFE_PORT_ID_QUINARY_MI2S_TX: + return Q6AFE_LPASS_CLK_ID_QUI_MI2S_IBIT; + + case AFE_PORT_ID_PRIMARY_TDM_RX ... AFE_PORT_ID_PRIMARY_TDM_TX_7: + return Q6AFE_LPASS_CLK_ID_PRI_TDM_IBIT; + case AFE_PORT_ID_SECONDARY_TDM_RX ... AFE_PORT_ID_SECONDARY_TDM_TX_7: + return Q6AFE_LPASS_CLK_ID_SEC_TDM_IBIT; + case AFE_PORT_ID_TERTIARY_TDM_RX ... AFE_PORT_ID_TERTIARY_TDM_TX_7: + return Q6AFE_LPASS_CLK_ID_TER_TDM_IBIT; + case AFE_PORT_ID_QUATERNARY_TDM_RX ... AFE_PORT_ID_QUATERNARY_TDM_TX_7: + return Q6AFE_LPASS_CLK_ID_QUAD_TDM_IBIT; + case AFE_PORT_ID_QUINARY_TDM_RX ... AFE_PORT_ID_QUINARY_TDM_TX_7: + return Q6AFE_LPASS_CLK_ID_QUIN_TDM_IBIT; + + default: + return -EINVAL; + } +} + int q6afe_port_set_sysclk(struct q6afe_port *port, int clk_id, int clk_src, int clk_root, unsigned int freq, int dir) @@ -1133,6 +1194,26 @@ int q6afe_port_set_sysclk(struct q6afe_port *port, int clk_id, struct afe_digital_clk_cfg dcfg = {0,}; int ret; + if (q6core_get_adsp_version() >= Q6_ADSP_VERSION_2_7) { + /* Always use the new clock API on newer platforms. */ + switch (clk_id) { + case LPAIF_DIG_CLK: + clk_src = Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO; + clk_root = Q6AFE_LPASS_CLK_ROOT_DEFAULT; + clk_id = Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE; + break; + case LPAIF_BIT_CLK: + clk_src = Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO; + clk_root = Q6AFE_LPASS_CLK_ROOT_DEFAULT; + clk_id = q6afe_get_v2_bit_clk_id(port); + if (clk_id < 0) + return clk_id; + break; + default: + break; + } + } + switch (clk_id) { case LPAIF_DIG_CLK: dcfg.i2s_cfg_minor_version = AFE_API_VERSION_I2S_CONFIG;
There are two APIs for setting clocks: the old one that uses AFE_PARAM_ID_INT_DIGITAL_CDC_CLK_CONFIG and AFE_PARAM_ID_LPAIF_CLK_CONFIG, and the new one which uses AFE_PARAM_ID_CLOCK_SET. ADSP firmware version 2.6 only provides the old API, while newer firmware versions only provide the new API. Implement LPAIF_BIT_CLK and LPAIF_DIG_CLK for both APIs so that users don't have to care about the firmware version. Also fall back to setting AFE_PARAM_ID_INT_DIGITAL_CDC_CLK_CONFIG in q6afe_set_lpass_clock when setting the new Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE clock is requested to allow specifying it in the device tree on older platforms too. Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> --- sound/soc/qcom/qdsp6/q6afe.c | 81 ++++++++++++++++++++++++++++++++++++ 1 file changed, 81 insertions(+)