@@ -85,6 +85,8 @@
#define AES_REG_IRQ_DATA_OUT BIT(2)
#define DEFAULT_TIMEOUT (5*HZ)
+#define DEFAULT_AUTOSUSPEND_DELAY 1000
+
#define FLAGS_MODE_MASK 0x000f
#define FLAGS_ENCRYPT BIT(0)
#define FLAGS_CBC BIT(1)
@@ -238,11 +240,19 @@ static void omap_aes_write_n(struct omap_aes_dev *dd, u32 offset,
static int omap_aes_hw_init(struct omap_aes_dev *dd)
{
+ int err;
+
if (!(dd->flags & FLAGS_INIT)) {
dd->flags |= FLAGS_INIT;
dd->err = 0;
}
+ err = pm_runtime_get_sync(dd->dev);
+ if (err < 0) {
+ dev_err(dd->dev, "failed to get sync: %d\n", err);
+ return err;
+ }
+
return 0;
}
@@ -520,6 +530,9 @@ static void omap_aes_finish_req(struct omap_aes_dev *dd, int err)
pr_debug("err: %d\n", err);
crypto_finalize_request(dd->engine, req, err);
+
+ pm_runtime_mark_last_busy(dd->dev);
+ pm_runtime_put_autosuspend(dd->dev);
}
static int omap_aes_crypt_dma_stop(struct omap_aes_dev *dd)
@@ -761,23 +774,6 @@ static int omap_aes_ctr_decrypt(struct ablkcipher_request *req)
static int omap_aes_cra_init(struct crypto_tfm *tfm)
{
- struct omap_aes_dev *dd = NULL;
- int err;
-
- /* Find AES device, currently picks the first device */
- spin_lock_bh(&list_lock);
- list_for_each_entry(dd, &dev_list, list) {
- break;
- }
- spin_unlock_bh(&list_lock);
-
- err = pm_runtime_get_sync(dd->dev);
- if (err < 0) {
- dev_err(dd->dev, "%s: failed to get_sync(%d)\n",
- __func__, err);
- return err;
- }
-
tfm->crt_ablkcipher.reqsize = sizeof(struct omap_aes_reqctx);
return 0;
@@ -785,16 +781,6 @@ static int omap_aes_cra_init(struct crypto_tfm *tfm)
static void omap_aes_cra_exit(struct crypto_tfm *tfm)
{
- struct omap_aes_dev *dd = NULL;
-
- /* Find AES device, currently picks the first device */
- spin_lock_bh(&list_lock);
- list_for_each_entry(dd, &dev_list, list) {
- break;
- }
- spin_unlock_bh(&list_lock);
-
- pm_runtime_put_sync(dd->dev);
}
/* ********************** ALGS ************************************ */
@@ -1140,6 +1126,9 @@ static int omap_aes_probe(struct platform_device *pdev)
}
dd->phys_base = res.start;
+ pm_runtime_use_autosuspend(dev);
+ pm_runtime_set_autosuspend_delay(dev, DEFAULT_AUTOSUSPEND_DELAY);
+
pm_runtime_enable(dev);
err = pm_runtime_get_sync(dev);
if (err < 0) {
Calling runtime PM API at the cra_init/exit is bad for power management purposes, as the lifetime for a CRA can be very long. Instead, use pm_runtime autosuspend approach for handling the device clocks. Clocks are enabled when they are actually required, and autosuspend disables these if they have not been used for a sufficiently long time period. By default, the timeout value is 1 second. Signed-off-by: Tero Kristo <t-kristo@ti.com> --- drivers/crypto/omap-aes.c | 43 ++++++++++++++++--------------------------- 1 file changed, 16 insertions(+), 27 deletions(-) -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-crypto" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html